Manual

ManualsBrandsXodus Innovations ManualsElectronicsBattery Powered Wireless Security Alarm with Key Entry, White

INSTRUCTION GUIDE

Key Pad Entry Alarm – HS4317D

ENCLOSED YOU WILL FIND:

• Key Pad Entry Alarm

• Magnet

• Double-sided tape

• Optional screws

TOOLS NEEDED:

• Small Phillips head screwdriver

BATTERIES NEEDED (not included):

• Three “AAA” alkaline batteries

INSTALLATION

For indoor use only. You must mount the alarm and magnet so the magnet rests

with its arrow pointing toward one of the alarm’s markings for proper alignment.

Choose a location that lets you install the magnet on a door or window and the

alarm next to it on the frame or vice versa. The distance between the alarm and

the magnet must be no more than 5/16 inch. Use the supplied screws or the

supplied adhesive tape and follow these steps to mount the alarm and magnet.

1. Remove the screw on the bottom of the alarm and remove the back cover.

2. Use two screws or two of the pieces of supplied adhesive tape to mount the

back cover. If using tape, make sure mounting surfaces are free of dust, oil and

other substances that could affect adhesion.

3. Install 3 “AAA” alkaline batteries onto appropriate terminals.

4. Slide the alarm onto the back cover.

5. Replace the screw on the bottom of the alarm.

6. Use the two remaining screws or the other piece of the supplied adhesive tape

to mount the magnet so the arrow points toward one of the markings on either

side of the alarm.

SETTING THE SECURITY CODE

You can set your own four-digit alarm security code.

• Your alarm’s security code is preset to 1234 at the factory. Be sure you use a

different security code.

• You must enter all four numbers within 10 seconds, or the red indicator turns off

and the alarm exits the procedure and resets to the previous security code.

• If you remove the battery, the security code resets to 1234.

Follow these steps to set your own security code.

1. Press keys 3 and 4 at the same time. The red indicator lights.

2. Enter the current security code. The yellow indicator flashes.

Note: If this is the first time you are setting the code, enter 1234.

3. Enter the desired four-digit code. The yellow indicator will flash once and a short

beep will sound to indicate a security code change.

ARMING/DISARMING

When the unit is powered up, two beeps will sound and then the unit will be in the

off mode. The unit can be turned on by pressing the keys 1 and 2 at the same

time. A beep will sound indicating the unit is armed. The unit can be turned off by

pressing the keys 1 and 2 at the same time. Two beeps will sound indicating the

unit is disarmed. To change between chime and alarm mode, the unit has to be

turned off first and set to the desired mode. Then turn on the unit.

1. Chime Mode

Simply set the mode switch to ”chime” and turn on the unit. The electronic chimes

sound when someone opens the door. If not, readjust the position of the magnet.

2. Alarm Mode

Set the alarm’s mode switch to ”instant” or “delay” and turn on the unit. Then close

the door. A beep will sound to indicate the unit is armed.

Note: If you don’t close the door within about 30 seconds, a continuous beeping

sound will alert you that the door is not closed. You can only turn off the beeping

sound by closing the door.

Summary of content (2 pages)

PAGE 1
INSTRUCTION GUIDE Key Pad Entry Alarm – HS4317D ENCLOSED YOU WILL FIND: • Key Pad Entry Alarm • Magnet • Double-sided tape • Optional screws TOOLS NEEDED: • Small Phillips head screwdriver BATTERIES NEEDED (not included): • Three “AAA” alkaline batteries INSTALLATION For indoor use only. You must mount the alarm and magnet so the magnet rests with its arrow pointing toward one of the alarm’s markings for proper alignment.
PAGE 2
The alarm sounds when someone opens the door. In delay mode, you will have about 10 seconds to enter the security code before the alarm sounds. In instant mode, the alarm will sound instantly for about 60 seconds or until you enter the security code. Note: After about 60 seconds, the alarm automatically shuts off and is armed again. The green indicator will flash to indicate there was an intrusion. Note: You cannot silence the alarm by pressing the keys 1 and 2 at the same time.