User Manual

• Observe temperature and humidity restrictions—Refer to the
Specifi cations table.
• Leave slack in the cable—Leave at least 10 ft. (3 m) of slack in
the communication and power cable to allow for adjustments in
the location of the Exciter.
• No user adjustments to internal circuitry—Tampering may
cause component or system failure, or both, and will void the
warranty.
Important Reference Documents
• Hugs Installation Manual (p/n 805I0301)
• Hugs System Manual (p/n 805U1601)
• Exciter Tester Sheet (p/n 806U6301)
Specifi cations
Materials Required
• Exciter. Includes door contact, L-bracket, adhesive mount, cable
ties, and bumpons.
• Facility fl oor plan indicating Exciter position and installation
orientation, and network wiring path.
• 105 Ω network terminator (p/n 805A2401) required to terminate
network. Two provided with each Controller (p/n 805A2201) or
Laptop Controller (p/n 805A2202).
• Mounting hardware, all installations:
• 4 Hollow wall anchors, for No. 10 wood screws
• 4 No. 10 x 1” stainless steel wood screws
• Additional mounting hardware, L-bracket installations:
• 4 No. 10 - 3/32” x 3/4” Philips/Pan head screws
• 4 Stainless steel hex nuts
• 4 No. 10 stainless steel fl at washers
• Optional: Passive infrared sensor for open doorways where door
contact cannot be used. Refer to Chapter 2 of the Hugs Instal-
lation Manual (p/n 805I0301) for important limitations on
using PIR sensors.
Installation Considerations
• Avoid metal—Do not install the Exciter behind or within 2
inches (50 mm) of metal objects, including metal doors. These
objects block the detection area of the Exciter.
• Use door contacts—Door contacts are required to minimize
nuisance alarms.
• Confi gure nearby Exciters as slaves—Exciters installed within
30 feet (9 m) of each other must be confi gured as master and
slave. Up to four slaves may be connected to one master.
Materials Required
Specifi cations
Installation Considerations
Important Reference Documents
Warranty
VeriChip’s products are warranted against defects in materials and work-
manship and shall perform in accordance with published specifi cations
for a period of one year. VeriChip reserves the right to change specifi ca-
tions without notice.
Limitation of Liability
This Product has been designed for use to assist in the prevention of
infant abduction and/or mother/infant mismatching.
The range, accuracy, function and performance of this Product may
vary from the published specifi cations due to many factors, including,
without limitation, site impairments from structural effects, metal objects
in the vicinity, placement of the receiver and transmitter, interference
from other electrical devices, atmospheric effects, installation, and
maintenance. There may be other factors, which also affect performance
of this Product.
VeriChip does not guarantee that this Product will detect 100% of infant
abductions and/or mother/infant mismatches. VeriChip does not guar-
antee that this Product will not return false reports of infant abductions
and/or mother/infant mismatches.
Monthly testing and maintenance of this Product, as described in the
Product documentation, is essential to verify the system is operating
correctly and to ensure that the probability of detecting an alarm and/or
locating the transmitter are maximized.
The failure to undertake regular testing and maintenance will increase
the risk of system failure and failure to detect infant abductions and/or
mother/infant mismatches. The failure to undertake regular testing and
maintenance will increase the risk of false reports of infant abductions
and/or mother/infant mismatches.
VeriChip hereby disclaims all warranties, express or implied, arising out
of or in connection with any of its Products of the use or performance
thereof, including but not limited to, where allowable by law, all other
implied warranties or conditions of merchantable quality and fi tness for
a particular purpose and those arising by statute or otherwise in law or
from a course of dealing or usage of trade.
VeriChip’s liability to you or anyone claiming through or on behalf of
you with respect to any claim or loss arising out of the use or misuse of
VeriChip’s Product, defective products or materials, improper installa-
tion or maintenance of VeriChip’s Product or products or the system
in which they are incorporated, or alleged to have resulted from an act
or omission of VeriChip or any person, negligent or otherwise, shall be
limited to:
a) the repair or replacement of defective Product or materials supplied
by VeriChip during the warranty period as set out in the Product
documentation; or, at the option of VeriChip,
b) refund of the purchase price of the Product supplied by VeriChip.
In no event shall VeriChip be liable for general, specifi c, indirect, con-
sequential, incidental, exemplary or punitive damages or any losses or
expenses suffered by you or anyone else, whether or not VeriChip, or
its employees, offi cers, agents, resellers or installers has been informed
of the risk of such loss or expense and whether or not such losses or
expenses were foreseeable.
Statements
United States—Federal Communication Commission (FCC)
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at his own expense.
Warning: Changes or modifi cations not expressly approved by VeriChip
could void the user’s authority to operate the equipment.
Canada—Industry Canada
The term “IC:” before the certifi cation/registration number only signifi es
that Industry Canada technical specifi cations were met.
European Union—CE declaration
VeriChip hereby declares that this radio frequency receiver is in compli-
ance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Service and Status Lights
The Exciter has a service light and status light, which may be used to
help diagnose problems in its operation. The service light is located
beside the wire terminals, and the status light is located on the
outside of the Exciter.
Service Light
Off Normal operation.
Momentary on Service Pin pressed.
Flashing every 0.5
seconds
Unconfi gured Exciter. Run Auto Confi gure.
On Hardware failure. Download fi rmware to the Exciter
from the LonWorks Device Installation dialog box.
Status Light
Red Alarm or Device Error.
Check for alarms and clear when security measures
have been implemented. If condition persists,
check operation of Exciter. Check the Exciter each
time before moving to the next step.
1 Press the Service Pin located on the front panel
of the Exciter. An alarm should appear in the
software. If not, check the wiring between the
Exciter and the Controller PC.
2 Click on the Test button in the LonWorks Devices
Installation dialog box. This checks the commu-
nications between the Exciter and the Controller.
If a warning message appears, continue with the
following steps.
3 Download fi rmware to the Exciter from the Lon-
Works Device Installation dialog box.
4 Reconfi gure the Exciter. Run Auto Confi gure in
the LonWorks Device Installation dialog box.
5 Reset the Exciter. Select the Exciter in the Lon-
Works Device Installation dialog box and click
the Reset button.
6 Use the Download Neuron command to update
the fi rmware.
If the above procedures do not fi x the Exciter,
replace it and check the replacement for coverage.
Green Armed.
Yellow • Sign In / Sign Out in progress
• Exciter permanently bypassed by the Controller
PC. These Exciterss do not activate alarms but do
send a message to the Controller PC indicating a
tag is within its detection area.
Flashing steady for
1 second, off for two
seconds repeatedly
(any color)
Wink command currently operating. The Controller
PC is in the process of identifying this Exciter on the
LonWorks network.
Frequency 125 kHz
Supply Voltage 12-30 VDC
Current Draw 200 mA @ 24 VDC, 500 mA maximum
Relay Outputs (2) 30 VDC, 1 A, NO or NC
Detection Radius Adjustable, up to 8.5 ft. (2.6 m)
Communications LonWorks two wire
Temperature Operating: 32°F to 120°F (0°C to 49°C)
Storage: -40°F to 176°F (-40°C to 80°C)
Humidity 0-85% RH @ 70°F (21°C), non-condensing
Dimensions Approximately 14.2 x 4.9 x 2 in. (360 x 124 x 50 mm)
Weight Approximately 18.7 oz. (530 g)
Part Number 806A6101
Exciter Installation Guide
Have
you:
• Pulled network and power cable?
• Resolved power supply requirements?
• Selected the location for the Exciter?
If you answered, “No,” to any of these questions, refer to the Hugs
Installation Manual before installing.
Read these instructions thoroughly
before installing the Exciter. Faulty installation can
lead to system failure.
© 2005 VeriChip Corporation. All Rights Reserved. Hugs and the Hugs logo are registered
trademarks of VeriChip Corporation Inc. in North America. VeriChip and the VeriChip log are
trademarks of VeriChip Corporation . All other company and product names may be trademarks of
their respective companies. Printed in Canada. August 2005 . 806U6101 Rev 01.
309 Legget Drive, Ottawa, ON K2K 3A3, Canada
Telephone: [phone] International: [phone] Facsimile: 1-613-592-4296
Web Site: www.verichipcorp.com
Certifi ed to the ISO 9001 Quality Standard