Installation & User Manual May 2000 © Copyright 2000, EXI Wireless Systems Inc. All rights reserved. Revision 1.
EXI ECO-Lite User Manual 980-000004-000 Table of Contents 1. Limited Warranty.................................................................................................................................. 3 2. Record of Changes................................................................................................................................ 4 3. FCC Regulations .................................................................................................................................
EXI ECO-Lite User Manual 980-000004-000 1. Limited Warranty EXI Wireless Systems Inc.
EXI ECO-Lite User Manual 980-000004-000 2. Record of Changes May 2000 EXI Wireless Systems Revision 1.0 Initial Release 4 May 2000 Revision 1.
EXI ECO-Lite User Manual 980-000004-000 3. FCC Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. EXI Wireless Systems CANADA Model No.: ECO-Lite Controller FCC ID: HE7 ELC * This device complies with Part 15 of the FCC Rules.
EXI ECO-Lite User Manual 980-000004-000 4. Introduction ECO-Lite is a long range proximity detection device usually used as a departure alarm. ECO-Lite detects the presence of EXI wrist or asset transponders within a prescribed detection zone. ECO-Lite may be used to: • Alert if people of property at risk are near an egress or danger zone. • Automatically open doors or activate equipment when a tag is present. • Indicate proximity of any "tagged" item or person.
EXI ECO-Lite User Manual 980-000004-000 5. Initializing the ECO-Lite System Before using the ECO-Lite System, the wireless keypad must be configured to communicate with the controller. The following procedure follows: 1. 2. 3. 4. 5. 6. 7. 8. 9. Plug in the 24V AC adapter into the controller power jack. Preset the rotary switch SW100 on the controller to match the keypad (position 0-7). Type Master password (9876- Factory Default) on keypad and then press the ‘Enter’ key.
EXI ECO-Lite User Manual 980-000004-000 6. ECO-Lite Controller The ECO-Lite has 3 lights to indicate status: Green Yellow Red (Standby) (Bypass) (Alarm) Front View • • • “GREEN LIGHT” indicates the power is on and the system is on standby. “RED LIGHT” FLASHING indicates an alarm is in progress (tag detected in range). “YELLOW LIGHT” & “RED LIGHT” alternately FLASHING indicates the system is in BYPASS Mode. Back View 8 Position rotary switch use to set the ID address between the keypad and controller.
EXI ECO-Lite User Manual 980-000004-000 7. Wireless Keypad The Wireless Keypad has 2 lights to indicate its status: LITHIUM BATTERY 8 POSITION ROTARY SWITCH BYPASS (Green) BATTERY LOW (Red) Back View Front View • BYPASS (Green) Light will flash when the bypass code is entered. • BATTERY LOW (Red) Light will flash once every 6 seconds when the battery is low on the keypad. Battery has an operating life of 5 years with an average of 100 keypad entries per day.
EXI ECO-Lite User Manual 980-000004-000 10. Password Management There are two types of passwords: Master password and User password. Master password is used to assign or delete User password. User passwords are used to bypass the system. There is only one Master password and 2 user passwords. All passwords are 4 digit numbers. 10.1. Master Password This password is used to change or delete User password or to change itself (Master password). To change Master Password: 1. Enter existing Master password 2.
EXI ECO-Lite User Manual 980-000004-000 11. Operational Mode Change To change the operation mode: 1. Enter Master Password 2. Press ‘ENTER’ key 3. Enter code for mode of operation: • “51” Test Mode • “52” Normal Mode with Unlimited Alarm Duration • “53’ Normal Mode with Fixed Alarm Duration 4.
EXI ECO-Lite User Manual 980-000004-000 13. Assigning the Keypad to the Controller The Keypad can only communicate to the Controller if they both have the same ID number. Each Keypad and Controller comes with 8-position rotary switch, which is used to set this ID number. Multiple Controllers could be programmed to respond to the same Keypad or multiple Keypads could be used to send commands to the same Controller (their ID settings should be the same).
EXI ECO-Lite User Manual 980-000004-000 17. Controller Enclosure The best position for this Controller is to be installed above the door (best field coverage). The controller is mounted to the wall by two mounting tabs. 18. Wireless Keypad Enclosure The base plate of the keypad is mounted to the wall with 4 screws and the keypad face plate simply snaps onto this base plate. The best position to mount the keypad is usually 8’-12’ away from the protected doorway.