XT6264 User Guide XT6264 User Guide Revised July 19, 2019 This user guide contains supplemental information about the XT6264.
XT6264 User Guide 1 CONTENTS 1 Contents ................................................................................................................................................ 2 2 Installation Procedure ........................................................................................................................... 3 3 2.1 Terminology .................................................................................................................................. 3 2.
XT6264 User Guide 2 INSTALLATION PROCEDURE 2.1 TERMINOLOGY Term Description Unit Xirgo XT6264 Asset Customer product that the XT6264 is mounted to. 2.2 INSTALLATION Figure 1: Hole Location Figure 2: Size of hole – 19mm 1. Install the unit bracket. 2. Secure the unused high voltage communication connector into unit bracket. 3. Install the unit into the bracket. a. Push the unit into the bracket b. Secure the two torx screws c. Push the ON/OFF switch 4.
XT6264 User Guide Figure 3: Ribbon Harness 6. Attach the TK bracket to the unit. 7. Fit the unit with the bracket TK controller and tighten the upper screws. 8. Connect the Power Cable Harness X1 RED wire to the Transformer X1 tap, and X2 BLACK wire (with ground terminal) to the Controller Chassis.
XT6264 User Guide Figure 5: X1 red to X1 tap Figure 6: X2 Black to ground chassis 9. Connect the 7 pin from the unit ribbon harness to the unit. 10. Bundle the cable by using cable ties and fix them to the unit. 11. Close the asset door.
XT6264 User Guide P a g e 6 | 14 CONFIDENTIAL AND PROPRIETARY Disclosure, storage and use subject to non-disclosure agreement
XT6264 User Guide 2.3 TESTING AFTER INSTALLATION 1. Connect the power plug to the power source. 2. Put the unit into install mode (ON/OFF button) – see Enter Install Mode for further description. 3. Observe installer LED for green pass – see observe Install LED below for further description. NOTE: if installer LED fails, refer to the trouble shooting guide and fix the issue. 4. Take the unit out of installer mode. 5. Close the controller door. NOTE: at this time, installation should be completed.
XT6264 User Guide 3 LED BEHAVIOR 3.1 TEST MODE When the device is in Active mode (i.e., not in ship mode or low power sleep mode), a push and release of the button when the green LEDs start blinking will cause the device to display status using LEDS as described below. LEDs will stay off in the normal device operation. NOTES: • • • 3.1.1 The push and release of the button when blue LEDs start blinking will put the device in INSTALL mode.
XT6264 User Guide LED Status Description GPS Lock Left-most LED ON means GPS is locked GPS Number Each LED following the left most LED represents three GPS satellites. Satellite numbers in between groups of three will be rounded up; e.g., four or five satellites in view will be represented with two LEDs.
XT6264 User Guide Battery Status (Yellow) • All five yellow LEDs will flash yellow for two seconds to indicate the device will provide battery status. • From left to right the backup battery value is indicated using solid yellow LEDs, which are held for five seconds. LED Voltage Left most LED (blinking) Volt < 2.9 One LED 2.9 < Volt < 3.2 Two LEDs 3.2 < Volt < 3.5 Three LEDs 3.5 < Volt < 3.8 Four LEDs 3.8 < Volt < 4.0 Five LEDs 4.
XT6264 User Guide 3.2 INSTALL MODE 3.2.1 Entering Install Mode The device must be active, i.e., either on battery hold off period or external power. This is not applicable during battery profile wakes (periodic, listen, motion start/stop). Press and hold the button until the blue LED is blinking; release the button. The device will reboot into install mode indicated by the fast blinking green LED. 3.2.
XT6264 User Guide 4 REGULATORY STATEMENTS 4.1 FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause Changes or modifications made to this equipment not expressly approved by Xirgo Technology may void the FCC authorization to operate this equipment.
XT6264 User Guide (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le onctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
XT6264 User Guide 2G/GSM LTE Antenna Specifications Parameter Band 5 Channel Frequency (MHz) Uplink Downlink Uplink Downlink 880-915 925-960 1710.2-1785.2 1804.8-1879.8 <2 <-5.9 <3.7 <2.