XT4970D Series User Guide Model: XT4970D FCC ID: GKM-XT4970D IC: 10281A-XT4970D Version 1.
Table of Contents Document Change History .......................................................................................... 3 1 Introduction ............................................................................................................ 4 1.1 Feature Matrix ................................................................................................................................................................................. 4 2 Hardware Description ............................
Document Change History Revision Date 1.0 11/25/2015 Author Changes Johnny Chen Document Creation based off XT4970D Series User Guide v3.
1 Introduction The XT4970D is a solar energy harvesting cellular and GPS tracking device supporting long term, remote deployments without the need to replace the rechargeable battery. This user guide describes the physical hardware, associated parts, the different mounting options available, and a quick start-up procedure. 1.
2 Hardware Description Below is a depiction of key interfaces of the XT4970D: Wake-up/ ZigBee Pairing Button Zigb Device/FCC Label Solar Panel LED Indicators 8-Pin Bayonet Connector The Associated Cable Harness that interfaces with the unit is shown below: 5
2.1 Hardware Specifications Cellular Technology Options LTE GSM GPS Specification Receiver 50 channels Receiver tracking Sensitivity Accuracy Cold Start Hot Start Power Requirements D.C. Power Current Consumption (4V Supply internal Battery) Max.
2.2 Cable Harness Description Pin # Wire Color 1 Blue 2 Brown 3 4 Yellow Black 5 Pin Name VBATT GND Functional Description Port Characteristic Ignition Sense Ground 8v to 24v, Internally pulled low 2.4 to 24V, < 0.
3 Device Mounting Options 3.1 Screw Mounting The XT4970D has two flanges (two holes per) at each end of the housing for screw mounting the device to the mounting surface. 3.
3.3 Trailer Cradle Mounting An optional trailer mounting cradle can be purchased for easy device mounting for the XT4970D. The cradle will need to be screw-mounted or VHB Tape mounted to the position desired. The XT4970D can be easily fastened into the cradle via a Phillips head screw. The angled edged of the cradle is designed to withstand the impact of snow scrapers that may come in contact to the cradle if mounted on the top of a typical trailer. 3.
3.5 Device Mounting Guidelines The XT4970D Series devices leverage solar energy to replenish the charge of its battery. Please consider the device mounting guidelines to maximize device solar charging. Also, the XT4970D series uses cellular and GPS technologies whose signal reception quality is depending on mounting location and style. Adhering to these guidelines will optimize the field performance of the XT4970D: If possible, have the solar panel facing directly towards the noon sun.
4 Quick Start Guide 4.1 Device Wakeup To start up the device, simply hold the black button located near the circular connector on the side panel of the device for 3 seconds. You should see the blue “C” LED light up and then fade out. The blue LED will blink when the device is successfully connected to the network. Refer to table in section 2.3 for LED behavior. Wake up Button Note: The factory default settings are configured to have the device to sleep within 2 minutes of wake.
4.2 Configuring the Device via SMS 1) 2) 3) 4) 5) 6) 7) 8) Ensure your device is active on your cellular account. Awaken device from sleep XT4970D via the “wake-up” button. If the device needs more power, then supply 12V DC via the red wire of the cable harness. Ensure device cellular LED is blinking based on LED definition in this document.
6) You can now configure the device by sending the XT commands listed in the protocol document of this device. a. Command +XT:1010 configures network settings b. Command +XT:3017 configures the sleep/wake mode for the device. i. The factory defaults for this device is to operate in the sleep timer mode and have a minute of wake time max. You may need to temporarily disable sleep in order to configure the unit uninterrupted by sleep. c.
FCC/IC: REGULATORY COMPLIANCE INFORMATION This equipment with FCC-ID: GKM-XT4970D and IC-ID: 10281A-XT4970D, HVIN: XT4970D is subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with license exempt Radio Standard Specifications of Industry Canada.