i-800 Product Information Guide
This guide contains helpful information that enables you to enjoy all of the features of your phone.
Introduction Thank you for purchasing the color DECT BT phone. Your new DECT (Digital Enhanced Cordless Telecommunications) can connect to an iPhone with Bluetooth function, which enables you to make calls through cell phone lines and landline. Enjoy these additional features, as well: Large displays and accessible menus. Color display - Customizable with wallpapers and brightness. iPhone charger - Charge an iPhone using a port on your new phone.
Technical Specifications Frequency Range 1.92~1.93GHz Channels 60 Duplex channels RF Carrier Power <100mW Modulation GFSK Frequency Stability <± Charging time 15 hours Ambient temperature Normal: 15℃ ~ 35℃Extreme:-20℃ ~50 ℃ Humidity 0%~90% Size (mm) Base: 255 x 74 x 67; Handset: 178.5 x 47 x 13 Power supply Base input: 7.5V, 2A; Handset input: Li-ion 1000mAh 50 KHz ? Design and specifications are subject to change without notice.
Contents Chapter 1: Getting Started 7 Features List Symptom Solution The handset can only receive calls. The keypad locked. Press and hold The phone doesn't work properly with some special services or if it is connected to an exchange extension (PABX). Check the Flash time and set it properly. The battery charge level is very low. Clean the charging pins, and if the problem is still not solved, replace the batteries. Logical malfunctioning in the handset or base unit.
Chapter 10: Additional Information 30 Last Number Redial Troubleshooting 30 Using a Pause Symptom The handset doesn't turn on. Solution Try charging the handset for a few minutes, then remove it from the base. If it still doesn't turn on, check the battery installation. If these efforts are unsuccessful, try replacing the batteries. Contact an authorized service center.
46 Editing or Deleting Contacts Handset 47 Download Phonebook from the iPhone PIN code Register Chapter 7: Settings 48 Changing the Handset & Base PIN Select base 50 Selecting a Base Reset handset 51 Resetting the Handset or the Base Auto answer 52 Auto Answer 53 Auto-Lock Auto-Lock 53 Language Language 54 Version Information Version Info 54 Flash Time Base Chapter 8: Date and Time PIN: (0000) 55 Date Format Flash time Dial mode 55 Time Format 56 Alarm Release handset 57 Sleep Mode
Chapter 9: Menu Structure Features List Bluetooth Add device Device list Display Brightness Wallpaper Handset name Sound Cell ringtone PSTN ringtone INT ringtone Key tone Power off tone Charging tone Call logs Incoming calls Dialed calls Contacts Home Cell 1 Cell 2 58 Chapter 1: Getting Started Color DECT BT Phone 1.8G/1.9G and 2.
Auto answering (selectable) 4 selectable wallpapers Call duration display Internal calling Password protection Mute function Real clock (12-hour or 24-hour) Keypad lock Redial, Flash, Pause Preparation dialing Sleep mode selection Alarm Landline FSK/DTMF Caller ID Incoming call indicator Private/Out of area notification Message waiting notification Selectable dialing mode Selectable Flash time 8 Sleep Mode This feature enables you to not be disturbed by the ring tone at night.
Alarm Phone Layout You can set an alarm to ring once or ring in regular intervals about every 10 minutes. Handset Power on /off button Activating the Alarm Feature Earpiece Charging indicator 1 Press 2 Press 3 Press beneath Menu to display the main menu items. Date and time to choose , then press beneath Select. beneath Select to choose Alarm. 4 Press Up or Down beneath Select. to choose "ON", and then press Navigation keys LCD Screen (2.
Key Functions Press to enter # or to switch between upper case and lower case letters in the English mode. Decrease the treble volume during music playing. Press and hold to turn on the keypad lock function. Decrease the bass volume during music playing. Increase the bass volume during music playing. Increase the treble volume during music playing. Select keys: Press to perform the function listed above the key. Chapter 8: Date and Time Date Format If you have set the date, you can choose the date format.
Version Information Select Keys 1 Press Press the left or right shown above it, on the display. 2 Press beneath Menu to display the main menu items. Handset to choose , then press button to initiate the function beneath Select. 3 Press Up or Down to choose Version Info, then press beneath Select. The current Handset model number, Hardware version, HS EMC code and Software version information appear.
Handset Screen Auto-Lock The screen shows various icons. When you have activated this feature, some time (about 25 seconds) later if no operation is taken, the keypad will be autolocked. Then you need to press the power on button on the top of the handset to unlock it. Signal strength. The greater the number of bars, the stronger the signal. The landline is engaged. 1 Press 0-9 Handset 2 Press The cellphone line is engaged. az or AZ beneath Menu to display the main menu items.
Resetting the Base 1 Press Package Contents beneath Menu to display the main menu items. Base 2 Press to choose , then press beneath Select. Once you have unpacked your phone, make sure that you have all of these parts. If any component is missing or broken, please call your dealer. 3 The handset prompts you to enter the current base PIN code (the default PIN is 0000). Use the numeric keys to enter the beneath OK. PIN, and then press 4 Press Up or Down beneath Select.
Connecting Resetting the Handset or the Base 1 Connect the plug of the power supply to the power jack of the base, and then plug the power supply into a standard AC wall outlet. If you reset the handset or the base, all of the user-selectable features restore to the factory settings: When resetting the handset, the incoming and outgoing lists will be erased, but the Contacts and Flash time do not reset.
Selecting a Base Notes: Your handset can be used with up to 4 base units, provided that it has been registered with them. This menu option enables you to select which base you want to use: 1 Press Do not insert or take out the battery when there is power supply connected. Replace battery if it doesn't recover its full storage capacity after recharging. beneath Menu to display the main menu items. Handset 2 Press to choose 3 Press Up or Down beneath Select. press or Down 4 Press Up beneath Select.
Base PIN Turning On or Off the Phone When you place the handset (DECT phone) on the base, it automatically turns on. To turn on the handset (when it's off), press the Power on/off button on the top of the handset. To turn off the handset, press and hold this button until Power off? appears. Then press OK to confirm, Goodbye! appears. 1 Press 2 Press beneath Menu to display the main menu items.
Chapter 7: Settings Changing the Handset & Base PIN Base and handset PINs are required to protect your phone against unauthorized use. They are set to 0000 at the factory. You can change the PINs as follows: beneath Select to confirm. The display asks you 6 Press to enter the AC (the authentication code is 0000). Enter this beneath Select. code and press 7 If the registration is successful, a confirm tone occurs and the new handset shows the handset number (e.g. 1).
Choosing the Dialing Mode 3 Press Your phone can be set to pulse dialing (rotary), or tone dialing (DTMF). To change the dialing mode: or Down to choose the desired option: 4 Press Up Edit - allows you to edit the selected entry. Delete - deletes the selected entry. Delete all - deletes all of the contact entries. 1 Press 2 Press beneath Menu to display the main menu items. beneath Select to display the option menus. Base to choose , then press beneath Select.
Speed Dial Notes: You can store up to 9 speed dial numbers on the numeric keypad (1~9), so you can easily dial the numbers by pressing and holding the associated numeric key. Storing Speed Dial Numbers 1 Press beneath Menu to display the main menu items. Contacts 2 Press beneath Select to choose beneath Select to choose Home. or Down 3 Press Up beneath Select. , then press to choose Speed dial, then press or Down to select the desired 4 Repeatedly press Up beneath Modify.
Chapter 2: Bluetooth and Remote Control Reviewing or Dialing a Number in Contacts Pairing with an iPhone You can search stored contacts by entering the first characters of their names (alphabetic search). You can also scroll through the entire list without accessing the Contacts menu. To use an iPhone with your DECT phone, you must first pair and connect the iPhone with the DECT phone. 1 Turn on the Bluetooth feature of your iPhone.
Method 2: In Standby Mode Method 2: Using the DECT Phone Menu 1 Enter a phone number, then press 1 Press beneath Save. beneath Menu to display the main menu items. Bluetooth 2 Complete storage by starting from Step 4 in the last paragraph of Method 1. 2 Press Character Map 4 The display shows all devices that have been paired before. Press Up or Down to choose the desired device, press beneath Select.
Disconnecting an iPhone 1 Press 2 Press Chapter 6: Contacts beneath Menu to display the main menu items. Bluetooth to choose 3 Press Down Select. , then press beneath Select. to choose Device list, press beneath 4 The display shows all devices that have been paired before. Press Up or Down to choose the desired device, press beneath Select. 5 Press beneath Select to choose Disconnect. Then a prompt tone occurs and Not Connected appears to the right of i-800 on the iPhone screen.
Dialed Calls List Removing a Paired iPhone The last 20 dialed calls are stored in the Dialed Calls list. You can review, redial, delete and save these numbers. If you already have the maximum of seven paired iPhones in the Device list and you want to add another iPhone, you must first delete a paired iPhone. 1 Press 2 Press beneath Menu to display the main menu items. Call logs to choose , then press beneath Select. or Down to choose Dialed calls, then press 3 Press Up beneath Select.
Remote Control for Music Notes: This feature allows you to control iPhone music playing via your handset or base. Method 1: Using the Handset 1 Insert your iPhone on the charging cradle of the base, then use it to play music. 2 Press beneath Menu to display the main menu items. Remote to choose , then press 3 Press to enter the following interface. At step 3, if the list is empty, "No record." appears. When "Missed calls xx" appears, you can press the OK key to access the Incoming Calls list.
Chapter 5: Call Logs Method 2: Using the Base Incoming Calls Insert your iPhone on the charging cradle of the base, then use it to play music. When you receive a call and you subscribe to your network provider’s caller ID service, if the caller's information is transmitted from the network on which the call was made (and the caller doesn't hide it), the caller's phone number is displayed. Additionally, you miss calls "Missed calls" followed by the number of missed calls (01, 02, etc.
Chapter 3: Basic Functions Charging Tone Making a Call When you dial, up to 25 digits appear on the screen. Every time you place the handset on the base, a tone occurs. This tone confirms that the handset is charging. You can switch the tone ON or OFF. You can place your calls in two ways: 1 Press beneath Menu to display the main menu items. Sound 2 Press Traditional Mode 1 Pick up the handset and press hear a dial tone, and appears. to engage the line. You 2 Dial a telephone number.
Key Tone Call Switching between the DECT Phone and an iPhone Every time that you press a key, your handset acknowledges it with a key tone. You can disable the key tones. During a call, you can switch between your DECT phone and your iPhone. 1 Press 2 Press beneath Menu to display the main menu items. Sound to choose 3 Press Up or Down beneath Select. , then press beneath Select.
Receiving a Call Ring Setting When a call is received, the phone rings and "Incoming Call" appears on the screen. indicates a landline call or indicates a cellphone line call. If the incoming call can be identified (i.e. The caller's information is transmitted) you also see the caller's number. You can select unique cell, landline and internal call ring tones and volumes. There are 15 ringtones, and four volume levels. You can also turn off the ringer.
Handset Name 1 Press 2 Press Using the Speakerphone beneath Menu to display the main menu items. Display to choose , then press beneath Select. 3 Press Up or Down to choose Handset name, then beneath Select. press 4 Press Up Select. or Down to choose "ON", press To turn on the speakerphone, press appears. during a call. beneath To turn off the speakerphone, press 5 Enter the name, up to 11 characters long that you want to beneath Save.
Last Number Redial Chapter 4: Display and Sound Your phone allows you to quickly redial the last dialed number. Brightness Pick up the handset and press to engage the line. Then press beneath Redial to dial the last-dialed number. This adjustment enables you to optimize the visibility of the display by changing its brightness according to environmental conditions. 1 Press 2 Press If your phone service includes call waiting or conference call services, you can use to initiate these functions.
Three-way Conference Calling Out of Range Indicator When you have an external call and an intercom call in progress, you can set up a three-way conference call, like this: The bars to the right of show the signal strength received from the base. If you are too far from the base, the radio signal might become too weak for the phone to access the telephone line. In these conditions you can't make or receive phone calls, and turns red and "Searching..." appears.
Paging Intercom You can page the handset from the base by making the handset ring with a special ring. It's useful to locate a lost handset or call the user who currently has the handset. If you connected more than one handset to a base (you can connect up to 5 handsets to the same base), you can have a conversation between two people using two different handsets. To send the paging signal, briefly press , located on the base. All handsets registered with the base ring for 15 seconds. .
Important Waring: and, if not installed and used in accordance with the FCC Caution: instructions, may cause harmful interference to radio Any Changes or modifications not expressly approved by the party communications. However, there is no guarantee that responsible for compliance could void the user's interference will not occur in a particular installation. If this authority to operate the equipment.
the applicable FCC Part 68 rules and requirements adopted by TEL: +630-654-9200 the ACTA. A compliant telephone cord and modular plug is FAX: +630-654-9219 provided with this product. It is designed to be connected to a If the equipment is causing harm to the telephone network, compatible modular jack that is also compliant. See the telephone company may request that you disconnect the installation instructions for details. 3.
d) Service Order Codes ("SOC") [9.0Y] This product meets the applicable Industry Canada technical specifications. / e) The FCC Registration Number [US: 6NYW400BI800] L e pré sent maté riel est conforme aux specifications techniques applicables 10. The REN is used to determine the number of devices that may be d'Industrie Canada. connected to a telephone. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call.