Instruction Manual

1.
a.
b.
c.
2.
a.
b.
c.
*
Made in China
INSTRUCTIONS:
Connect the provided Micro-USB cable to
the USB plug adapter.
Connect the Micro-USB tip to the input port
on the charging pad.
Insert corresponding charging cable into
the Charging Pad USB port.
Charging Mobile Devices:
Ensure that your phone or tablet supports
wireless charging. It will be listed in the
the last page of this manual).
Place the enabled device on the surface
of the wireless charging pad. The device
should display charging indicator.
When completely charged, remove the
device from the charging pad.
Note: To charge devices, use only the
accessory cable or the cable included with
your own device by the manufacturer.
Bora Wooden Wireless
Charging Pad
Instruction Manual
XO-9549
FCC ID:2ADK3XO-9549
1 x Wireless Charging Pad
1 x USB to Micro-USB Charging Cable
1 x Instruction Manual
Input power: 5V/1A
Output power: 5V/750mA
While device is charging LED will illuminate
RED.
1.
2.
3.
•
•
•
Micro-USB Input Port
LED Indicator
Charging Pad Surface
What’s included:
Function:
LED Indications
***
KEEP OUT OF REACH OF CHILDREN***
SAFETY PRECAUTIONS:
FCC Statement:
WARNING-When using this product, basic
precautions should always be followed:
Read all the instructions before use.
Never store or use this product in
temperatures below 32°F (0°C) or above
115°F (45°C).
Do not overcharge your phone. The
unit may become hot under excessive
use. Remove your phone once it is fully
charged. Never charge your phone for
more than 7 hours at a time.
To reduce the risk of injury, close
supervision is required when the product is
used near children.
•
1.
2.
3.
4.
5.
Do not expose the device to moisture.
Read all the instructions before using the
product.
6.
7.
8.
9.
10.
11.
12.
Do not use the device in excess of its
output rating. Overload outputs above the
Do not use the device if damaged or
explosion or risk of injury.
Do not disassemble the device. For repairs,
Incorrect reassembly may result in a risk of
or temperatures above 104°F (40°C) may
result in explosion.
To ensure product safety, ensure that
identical replacement parts.
Attachments on the back of your phone can
impede the effectiveness of the wireless
charger, and lead to overheating. Please
remove attachments from the phone before
charging on this device.
SIZE:89*165mm
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help
Changes or modifications not expressly approved
by the party responsible for compliance
could void the user's authority to operate the
equipment.
This device complies with Part
15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
RF Exposure Warning Statements:
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.This equipment shall be installed
and operated with minimum distance 20cm
between the radiator & body.