User Manual
Table Of Contents
®
XIAOKOA
UHF Wireless Microphone
User manual
(Headset)
The device has applied UHF wireless technology
with low energy, long standby for 6 hours.It can
be transmitted 50m maximum under laboratory
data and without direction limitation .
3.5 mm Microphone
audio output jack
Working status indicator
Working status
indicator
Mic
Power
switch
Charging jack
Charging jack
Charging status
indicator
Figure1
(Wireless Transmitter)
Volume
Features
Product Overview
1.How to set up on amplifier
Headset and receiver connection method
3 4
Long press“vol+”for
3 seconds, the blue
light flashes quickly
and then loosens.
1 2
MIC
1.
.
Note:
Please follow above the order of 1-4, if the receiver
is flashing for more than 10 seconds, please turn
off the receiver and then turn it back on.
Note: Please follow this step to set up, or it
will not work.
2.How to use multiple UHF devices
If you use more than 2 UHF devices within 80 m,
please follow this step to set up.
1
2
3
4
How to dissemble
Step 2: Use 2 thumb to press
down the headset holder
at the same time.
Step 1
Step 3
After remove it, the
headphone will
separate out.
:
Step 4
When wan to assemble,
there will be a joint and
allign it by using 2 thumb to
push it up.
:
How to Assemble
Introduction
Thank you for purchasing this wireless
microphone, please read this user manual
carefully.
Tips
The product must be set up on windows first and
secondly turning on the recording software.
Specification
Sampling Frequency
Modulation Method
The Speaker size
RF Transmission power
Transmission Distance
RX Sensitivity
S/N Ratio
16KS/s
GFSK
3 inch
10dbm
40m
-88dbm
≥65db
Warranty
Customer Service
@XIAOKOA
support@xiaokoa.com
http://www.xiaokoa.com
At XIAOKOA we believe in our products. That’s
why we back them all with 1 years warranty and
provide friendly, easy-to-reach support.
Please feel free to contact us if you
encounter any problem that you cannot solve!
PLS CONTACT US DIRECTLY WITH ANY
QUESTION OR ISSUE WE ARE ALWAYS HERE TO
ASSIST YOU, THANKS!
No sound
can't work/
the blue light
flashing
quickly
Problem
Low voice
Solution Way
Check whether the connection between the transmitter
and receiver is successful. (If successful, the blue light
stop flashing.)
Make microphone more close to your mouth,
pressing the “+” button on the transmitter to
increases the volume.
Adjust volume of voice amplifier
Can't listening when recording,it can be can listen
after finished。
Transmitter or receiver low battery,need charging soon.
Can't connect
successfully
1. Turn off the receiver and transmitter
2. Turn on the transmitter,press and hold the "+" button
on the transmisster for 3s, blue light will flashing
3. Turn on the receiver and wait for the connection
4. The blue lights of the transmitter and receiver stop
flashing, mean connect successfully.
How to reset
Firstly.turn off the transmitter and receiver.
Secondly,press volume"+" button of transmitter and
don't loose,turn on the switch at the same time,the blue
light will blinking several times,
Finally,loose the volume"+" button,reset finished.
®
XIAOKOA
ワイヤレスマイク
取扱説明書
( ヘッドセット式)
UHF 12
この度は弊社の製品を買い上げいただきありがとうございまし
た。ご使用前には、必ずこの取り扱い説明書をお読みのうえ、
正しくお使えいください。
ヘッドセット式マイクは2.4G技術を採用して、省エネ
の同時に約6時間の作業が実現する。本品は各方向で
送信ができる。理想な転送距離は50メートル以下であ
り、作業効果がより良い。
機 能
3.5 mm
出力ジャック
作業インジケータ
Mic
無線送信機
音量ボタン
各部の名称
充電ジャック
充電
インジケータ
電源
スイッチ
充電ジャック
電源
スイッチ
充電
インジケータ
作業インジケータ
無線受信機
6.35 mm
出力ジャック
拡声器の接続例
3
4
送信機の「VOL+」ボタンを
約3秒に押す、青い が
点灯して作業開始。
ライプ
1
2
MIC
注意:1~4の順番で操作してください。受信が10秒以上
点滅している場合は、受信器の電源を切り直してください。
1.
送信機の電源スイッチを
押す。
受信機も同じ方法で開く、青
いライプが点灯して自動的に
接続する、完了信号はライプ
の点滅が止まる。
受信機を増幅器のMICポート
に挿入する。(ジャックのPA
機器を使用する場合、まず受
信機を6.35mm出力ジャック
挿入する。)
注意:この手順で設定してください。
複数のUHFデバイスの使用方法
80メートル以内にUHFデバイスを2台以上使用する場合
は、この手順に従って設定してください。
1
2
3
4
上の「拡声器の接続例」の手順を参照すると、設備が自動
的にマッチングする
製品は記憶の機能があるので、初めて接続した後次回に直
接に使える。
接続する時、設備が別の電子製品の信号やノイズによって
妨害されていないことを確保する。てなくと、もう一度接
続するしかない(step2に繰り返す)。
第二台目の送信機の「VOL-」ボタンを約3秒に押すと、別
の周波数に切り替える。同様、青いライプが点灯して自動
的に接続する、完了信号はライプの点滅が止まる。
バラメータ
サンプリング周波数
16KS/s
GFSK
10dBm
30~50m
-88dbm
≥65db
4~6時間
変調方式
RF送信電力
理想送信距離
作業時間
RX感度
S/ N比
▲作業時間と送信距離は環境によって変わる。
取り付け
親指でクリップを押して開く、
ヘッドセットを取り外す。
Step 1
それを取り除いた後に、
ヘッドホンは分離します。
組立 場合
親
が必要な はコネクター
を 指で押して位置合わせすれ
ばいい。
Step 2
組み立てる方法
Step 4
Step 3
組み立てる状態
よくある質問と解決方法
こんな時
解決方法
声が小さい
送信機と受信機の接続が成功したことを確認する。
(成功すれば青い の点滅が止まる。)ライプ
録音の時、声が
出ない
この製品は録音している時、自分の声を聞こえない。
録音終了後再生ことができる。
初期設定を戻す
送信機上の「+」ボタンを押しながら、電源スイッチ
押す。青い 約5秒点滅すると、マイクは初期設
定を戻す。「+」ボタンを放す、設定完了。
ライプ
接続成功できな
い
送信機と受信機の電源を切る。送信機の「+」ボタン
を約3秒に押す、青い が点灯して作業開始。
送信機の電源スイッチ押す、青いライプが点灯して
自動的に接続する、完了信号は両者もライプの点滅
が止まる。
ライプ
作業できない/
マイクは作業な
がら青い
が高速点滅して
る
ライプ
送信機上の「+」ボタンを押す、音量が大きくなる。
拡声器などの再生機器の音量を調整する。
送信機或いは受信機の電池状態不足。できれば早く
充電する。
@XIAOKOA
お問い合わせ
support@xiaokoa.com
http://www.xiaokoa.com
品質管理には万全の注意をはらって おります、製品の保証期間は
一年です。このうちに、何か問題が あればぜひご連絡ください。
保証期間
95*130mm