深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. C-3L_V1.0 C-3L specification (WiFi &BLE module) product model ：C-3L document number ：XZX_RD_SP_C-3L V1.0 hardware version ：V1.0 Revision No ：V1.0 commencement date ：2020-08-19 文件含（C-CHIP)机密文件，未经许可，不可外传 File include (C-CHIP) confidential documents, without permission, can not be disclosed 地址：深圳市宝安区沙井东环工业区 A3 栋 公司网址：WWW.C-CHIP.COM.
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. C-3L_V1.0 变更记录 Change History： versions V1.0 变更记录 revise contents page / Make first revision date 2020-08-19 reviser verifier pingzhou contact information Website：WWW.C-CHIP.COM.CN phone：0755-29179480 /81 /82 fax：0755-84736169 address：Building A3, Shajing Donghuan Industrial Zone, Baoan District, Shenzhen 地址：深圳市宝安区沙井东环工业区 A3 栋 公司网址：WWW.C-CHIP.COM.
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. C-3L_V1.0 目录 1 2 3 4 5 6 7 8 Summary................................................................................................................................................................. 4 Features................................................................................................................................................................... 4 Application Field..........................................................
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. 1 C-3L_V1.0 Summary C-3L is integrated with WIFI&,ARM9 32-bit MCU core,120MHz master frequency, 256Kbram built-in, Bluetooth BLE dual-mode module, C-chip CC8000_QFN32-- integrated MCU/WLAN MAC/ Baseband/RF integrated single-chip solution。 Support 802.11b /g/n WiFi standard. • Support 802.11b/g/n standard, HT-20 • Supports Station, Soft AP, Station+Soft AP Maximum transmission rate of 72.
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. C-3L_V1.0 4 Module block diagram 5 Performance Parameter 5.1 Module parameters WLAN STANDARD ANTENNA frequency range Module parameters WIFI 802.11b/g/n, 1T1R PCB antenna 2.4G WIFI: 2412-2462 MHz BLE: 2402-2480 MHz Type of wireless network IEEE802.11b <17 dBm IEEE802.11g 14 dBm IEEE802.
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. authentication information C-3L_V1.0 in authentication 5.2 Recommended working conditions opereating range operating temperature range VCC I/O power supply (VDD_PIO) AIO input frequency range Min -40 Typical - Max +125 Unit °C +3.1 3.1 0 2400 +3.3 +3.3 - +3.6 +3.6 +3.6 2484 V V V MHz 5.3 limit range opereating range storage temperature VCC operating voltage I/O power supply Min Max -40 0 0 Unit +125 +3.6 +3.6 °C V V 5.
深圳市芯中芯科技有限公司 C-3L_V1.0 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. 5.5 RF Parameter Parameter operating frequency transmitted power receive sensitivity Model IEEE802.11b Min 2412 - typical 17 14 13 6 - Max 2484 -90 IEEE802.11g IEEE802.11n BLE - - -73 -71 -95 IEEE802.11b IEEE802.11g IEEE802.11n BLE unit MHz dBm dBm dBm dBm dBm dBm dBm dBm annotation：The above test results were at room temperature of 25 degrees and 3.3V power supply mode 5.
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. electrostatic discharge machine mode 6 condition HBM ,TAMB=25°C parameter +/-200 C-3L_V1.0 unit V Mechanical Size and Pin Definition 6.1 Module size drawing 6.2 Module Pin Definition Diagram 地址：深圳市宝安区沙井东环工业区 A3 栋 公司网址：WWW.C-CHIP.COM.
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. C-3L_V1.0 6.3 Pin function description Pin Type I I/O I Description Pin Name 1 2 3 RST P23_ADC/TDO EN 4 P14 I/O P14 5 6 7 8 9 10 11 12 13 14 15 16 PWM5 PWM4 PWM0 3V3 GND PWM3 UART2 P16 PWM2 PWM1 1RX 1TX I/O I/O I/O P G I/O I/O I/O I/O I/O I/O I/O PWM5 PWM4 PWM0 Power input(3.3V-3.6V) GND PWM3 UART2 P16 PWM2 PWM1 1RX 1TX reset, active low P23 or ADC or JTAG TDO Chip enable, active high Notes: 1. I：Input 2. O：Output 3. P：Power 4.
深圳市芯中芯科技有限公司 SHENZHENSHI XINZHONGXIN TECHNOLOGY CO., LTD. C-3L_V1.0 C. Pcb cloth board: because the metal will weaken the function of the antenna, when the module cloth board, it is forbidden to lay the ground and walk the line under the module antenna, if it can be hollowed out better. D.
FCC regulatory compliance statement §15.19 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. §15.21 Information to user Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Antennas This module is tested with PCB antenna, and the Max. antenna gain is 0dBi. If you desire to increase antenna gain and either change antenna type or use same antenna type certified, a Class II permissive change application is required to be filed by us, or you (host manufacturer) can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application.
Additional testing, Part 15 Subpart B disclaimer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer in any case shall ensure host product which is installed and operating with the module is in compliant with Part 15B requirements.
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
