ZETA Dry Contact Sensor ZETA Dry Contact Sensor 1
ZETA Dry Contact Sensor Copyright Statement ZiFiSense owns the copyright on this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of ZiFiSense. Disclaimer This specification is preliminary and is subject to change at any time without prior notice. ZiFiSense assumes no responsibility for any errors contained herein. ZiFiSense is not responsible for any patent infringement of third party on its use or as a result of its uses.
ZETA Dry Contact Sensor Table of Contents 1. Product Description........................................................................................ 4 2. Applications..................................................................................................... 4 3. Appearance...................................................................................................... 4 4. Features............................................................................................................
ZETA Dry Contact Sensor 1. Product Description ZETA Dry Contact Sensor uses electrodes to detect the dry contact signal and generates alarm. Otherwise it remains in standby mode with ultra-low power consumption when there is no such signal triggered. 2. Applications Building property and industry where dry contact sinals are need to be detected. 3. Appearance 4.
ZETA Dry Contact Sensor 5. Specifications Product No. Wireless Features Electrical Features Physical Features Working Environment OCZ1ZT92 Transmission protocol Frequency band Output power Power supply Battery capacity Stand-by current Working current Size Enclosure material Waterproof level Antenna Operating temperature Storage temperature 6.
ZETA Dry Contact Sensor 7. Installation There are three installation methods: Screw, 3M Adhesive and cable ties. 7.1. Screw 7.1.1.Auxiliary material No. 1 2 3 4 Materials self tapping screw (M3*20) #4 expanded plastic pipe Percussion drill，#4 drill bit，hammer slotted screwdriver, cross screwdriver 7.1.2.Installation instructions Quantity 2/device 2 1 1 Open the device case Use a slotted screwdriver to open the top cover from the bottom edge.
ZETA Dry Contact Sensor Use the self-tapping screws to secure the device in the mounting position. mounting hole mounting hole Power on Insert the power plug into the upper power socket, install two 14505 batteries (remove the insulation sheet for the existing battery), and close the upper cover.
ZETA Dry Contact Sensor 7.2. Adhesive 3M 7.2.1.Auxiliary material No. 1 2 Materials 3M seamless thickened double-sided adhesive Slotted screwdriver, utility knife Quantity 5CM 2 7.2.2.Installation instructions Installation position Select a flat mounting position, and clean it up. Open the device case Use a slotted screwdriver to open the top cover from the bottom edge.
ZETA Dry Contact Sensor power socket Adhesive device Take the appropriate amount of 3M adhesive, attach it to the back of the sensor, remove the protective film of the 3M adhesive, and install the device to the specified position. 7.3. Cable Ties 7.3.1.Auxiliary material No. 1 2 Materials Metal cable ties（5*300mm) Slotted screwdriver, utility knife Quantity 2 7.3.2.Installation instructions Open the device case Use a slotted screwdriver to open the top cover from the bottom edge.
ZETA Dry Contact Sensor opening Fixation Pass the 2 cable ties through the device and secure to the installation rod Installation position 10
ZETA Dry Contact Sensor Power on Insert the power plug into the upper power socket, install two 14505 batteries (remove the insulation sheet for the existing battery), and close the upper cover.
ZETA Dry Contact Sensor 8. Use of Device 8.1. Steps for usage Place the device within the coverage of the ZETA network Install the battery, and wait for the device to go online. After the device is online, the current device status is reported. According to the usage scenario, set the policy configuration such as heartbeat reporting cycle. Daily maintenance and data viewing. 8.2. Support function Version number: Report the software version number of the sensor only once after power-on.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ZETA Dry Contact Sensor 13
