Installation Instructions

ManualsBrandsXiamen Tenia Lighting & Electrical ManualsElectronicsSmart Switch

Smart Switch Installation

Instructions Manual

Model No. SNA042CLR3-ZB-1X600-

Rated Voltage 120-277V～

Rated Frequency 60Hz

Operating Voltage

120V～ 277V～

Load Range

Incand. 5A 3A

LED/CFL 5A 3A

Res 5A 3A

Motor 1/6 HP 1/6 HP

Communication

module

ZigBee

Operating

Environment

Temperature： 0℃ - 40℃

Humidity：10% R.H. - 90% R.H.

Usage Environment

Indoor use only

Model Size 105 mm×44 mm×33mm (L×W×H)

Model No. SNA042CLR3-ZB-1X1200-

Rated Voltage

120-277V～

Rated Frequency

60Hz

Operating Voltage

120V～ 277V～

Load Range

Incand. 10A/1200VA 8A/ VA

LED/CFL 10A/1200VA

Res 10A/1200VA

Motor 1/2 HP 1 HP

Communication

module

ZigBee

Operating

Environment

Temperature： 0℃ - 40℃

Humidity：10% R.H. - 90% R.H.

Usage Environment Indoor use only

Model Size 105 mm×44 mm×33mm (L×W×H)

△

WARNINGSAND CAUTIONS

 To protect against the dangers of fire and electric shock, a

product has to be installed according to electrical codes and

standards.

 This product should be use together with an upstream

air-switch.

 Turn power off at circuit breaker or fuse and test that power is

off before installing.

 If you are unsure about any part of these instructions, consult a

licensed electrician.

RF EXPOSURE STATEMENT

This equipment complies with the FCC RF radiation exposure limits

set forth for an uncontrolled environment. This equipment should be

installed and operated with a minimum distance of 20cm between the

radiator and any part of your body.

This equipment meets the exemption from the routine evaluation

limits in section 2.5 of RSS-102. It should be installed and operated

with a minimum distance of 20cm between the radiator and any part

of your body.

Cet équipement est conforme à l'exemption des limites d'évaluation

habituelle de la section 2.5 de la norme RSS-102. Il doit être installé

et utilisé à une distance minimale de 20 cm entre le radiateur et toute

partie de votre corps.

IC Information

This device contains licence-exempt transmitter(s) that comply with

Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two

conditions:(1) This device may not cause interference.and (2) This

device must accept any interference, including interference that may

cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent

appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes:

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d’en compromettre le fonctionnement.

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

This device may not cause harmful interference, and (2) This device

must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

FCC CAUTION

Any changes or modifications to this unit not expressly approved

by the manufacture could void the user's authority to operate the

equipment.

Function Parts Information

RESET

Short press: Within 0.5s .

Long press: Over 5s.

Status Indicator

 Indicator lights red: OFF status.

 Indicator lights green: ON status.

 Green Indicator flashing: enter distribution network mode.

ON/OFF

 Load power ON: When the load is powered off, press the ON

button once.

 Load power OFF: When the load is powered on, press the OFF

button once.

 Network mode: when the light is on, Long press ON or OFF for

5 seconds. After the status indicator blinks quickly, the phone

can be connected to the smart switch. (if it is not connected, exit

the network mode after 3 minutes).

Self-reset Switch

 Network mode: when the light is on, Long press the reset switch

for 3 seconds. After the status indicator blinks quickly, the

phone can be connected to the smart switch. (if it is not

connected, exit the network mode after 3 minutes).

Power Cut -off Button

 Put in the power cut-off button to connect the power.

 Put out the power cut-off button to cut off the power.

Parts Information

RESET

Smart Switch

（1pc）

Jumper Wire(1pc)

Mounting

Frame(1pc)

Panel(1pc)

P3 Wire

connectors(6pcs)

Mounting

screw(2pcs)

Tools needed to install your smart switch

Φ3mm Slotted

Screwdriver

Φ5mm Philips

Screwdriver

Electrical

Tape

Cutters

Pliers Test Pencil Ruler

Installation and testing

Step 1

△

WARNING: To avoid fire and electrical shock,TURN

OFF POWER at circuit breaker or fuse and test that power is off

before wiring.

Step 2 Removing existing switch: Remove existing wall plate and

switch mounting screws. Carefully pull switch from wall box, identify

and take out the wires attached to the switch, then remove the switch.

DO NOT remove wires which are taken out from the switch at this

time.(If new configuration is without this step)

Step 3 Identifying your wiring application

NOTE:If the wiring in the wall box does not resemble any of

these configurations, consult an electrician.

②

①

③

④

②

①

②

③

④

⑤

②

Single-Pole

①Line (Hot)

②Neutral

③Ground

④Load

3-Way

①Line or Load

(See note below)

②Neutral

③Ground

④Traveler 1

⑤Traveler 2

Self-reset switch

Status Indicator

Power Cut -off Button

OFF

2216

8A/ VA

2216

8A/ VA

2216

Summary of content (3 pages)

PAGE 1
Smart Switch Installation generates, uses and can radiate radio frequency energy and, if not ! WARNINGSAND CAUTIONS △  Instructions Manual   harmful interference to radio communications. However, there is no To protect against the dangers of fire and electric shock, a guarantee that interference will not occur in a particular installation. If product has to be installed according to electrical codes and this equipment does cause harmful interference to radio or television standards.
PAGE 2
Please note that for 3-way application,there have a power cord from Location 1 the original switch be a different color (Black) or marked Common. Screw 1 Tagged Wire and 3-way junction box and marking as common (live or load). Ground (Green or Bare Copper) Location 1 wiring: Neutral and Live wire for better compatibility.
PAGE 3
Table2 3 - way Function table 3-way Function smart switch Operation Way smart Switch switch or Toggle Operation Switch  Mobile app operation Step 1 Download the ‘Smart Life’ App APP Operation  Use your mobile device to scan the QR code below or search  for "Smart Life" in the App Store or Google play to download Make sure the App control indicator LED1 is blinking, click Step 5 Use the phone App to control smart switch Confirm the indicator is blinking…,click  Click switch.