300 Series Printer User Manual
Xiamen Rongta Technology Co., Ltd. Catalog I Notice...................................................................................................................................... 3 1.1 Safety Notice ................................................................................................................... 3 1.2 Usage Notice.................................................................................................................... 3 1.3 Storage Notice .................................
Xiamen Rongta Technology Co., Ltd. www.rongtatech.
Xiamen Rongta Technology Co., Ltd. I Notice Please read the following information carefully before using the printer! 1.1 Safety Notice (1) This printer can only use battery and power adapter provided by our company, or it may cause damage to the printer, battery leakage, fire or explosion. (2) Do not put the battery into the fire, not make it short circuit, break up or heating, otherwise it may cause the battery leakage, fire or explosion.
Xiamen Rongta Technology Co., Ltd. (5) The printer could work stably from -10°C to 50°C, but the higher temperature (>/=45°C) or lower temperature (/=85%) or lower humidity (
Xiamen Rongta Technology Co., Ltd. voltage and bring unusual chemistry reaction, then cause the overheating, burning and/ or explosion of it. (2) Do not use or place the battery near burner or high temperature environment. Overheating may cause the damage to the resin shell and/or heat insulation material, and bring the short circuit in the battery then lead the overheating, burning and/ or explosion of it. (3) Please use dedicated charger when charging.
Xiamen Rongta Technology Co., Ltd. (9) Do not throw the battery or make it damaged. If the safety device in it is burned out, any charging of it would bring abnormal current and/or voltage, bring unusual chemistry reaction, then may lead to overheating, burning and/or explosion of it. II Product Introduction 2.1 Printer outer design 8 7 2 1 6 3 4 5 9 10 11 12 1. Feed Key 2. Status Indicator www.rongtatech.
Xiamen Rongta Technology Co., Ltd. 3. Battery indicator 4. Error indicator 5. Power Key 6. Body 7. cover opening button 8. transparent cover 9. Printer Top Cover 10. Power supply interface 11. USB interface 12. Battery Cover 2.2 Accessories Standard Accessories Battery CD-ROM Optional Accessories Leather Sheath www.rongtatech.
Xiamen Rongta Technology Co., Ltd. III Performance 3.1 Print Performance Printing way: Direct thermal print Paper width: 79.5±0.5mm Printing width: 72mm Resolution: 8dots/mm (203dpi) Dot/line: 576dots Printing speed: 60mm/s (Max) Paper thickness: 60-80μm Printing Contents: Support all GB18030 Chinese character, PC437,Katakana,PC850,PC860,PC863,PC865,WPC1252,PC866,PC852,PC858; Barcode:CODE39,EAN-13,EAN-8,CODABAR,CODE93,ITF; QR CODE, PDF417. 3.
Xiamen Rongta Technology Co., Ltd. Power: 2000mAH rechargeable li-ion battery Power alarm: battery indicator light will be out and Error indicator light (Red) will be on when printer will run out of power. Adapter to recharge: battery can be filled in with 5 hours. Notice: The battery can’t recharge by using Adapter and USB at the same time. A charging time available: Normally, the battery could be used for printing 200 meters or 6 hours.
Xiamen Rongta Technology Co., Ltd. Transparency cover Pinch both sides Rubber roll Usage Method 1. Poke up the key of opening cover or use fingers to keep pressing the sides of cover then open it. 2. As shown in picture, please put the paper roll in and do not put it in wrong direction, otherwise it would lead the printer unable to work. 3. As shown in picture, pull out part of paper; please make sure to pull the paper out of the paper roll compartment. 4.
Xiamen Rongta Technology Co., Ltd. 4.2 Basic Function 4.2.1 Power On Under power off status, keep pressing "POWER" key for two seconds, printer will be powered on and on working status, then power indicator (green light) lights. Note: If printer power indicator (blue light) goes out and the error indicator (red light) lights, it means the printer is going to power off, please change the battery or charge it. Charging method please refer to (4.2.5 charging). 4.2.
Xiamen Rongta Technology Co., Ltd. light) will keep flashing from left to right repeatedly till the charging is finished and the charge indicator is keep lighting. 4.3 Printer Connecting and Printing 4.3.1 USB Interface Connecting Printer's optional accessories contain USB Wire, Connect to PC and install the USB driver. 4.3.2 WI-FI Communication User could use wireless network technology to connect with your equipment for date communication.
Xiamen Rongta Technology Co., Ltd. 4. If the encryption type for route is “WEP”, the setting of wifitool should fit to the route. 5. After connecting printer with computer by virtual serial connection via USB port and finish all the wifi parameter, please choose the relevant serial port in wifitool, for example COM8, and set up the default baud rate of printer as “19200”(if customers set up baud rate through dial switch, input the right one),then apply it. 4.3.
Xiamen Rongta Technology Co., Ltd. serial port, and you want to drive the RPP300 portable mini printer, please consult your PC supplier. 4.4 Indicator Light and Buzzer Signal Description Printer has a buzzer and two indicators light that used to prompt the user the status of the printer, the light is used to represent the current status of the printer, and buzzer used to prompt the printer status changes. Two indicator lights are respectively function indicator light and charge indicator.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.