Thermal Receipt Printer User Manual
Catalogue I. PRODUCT INTRODUCTION .........................................................................................2 1.1 Warnings: ......................................................................................................................2 1.2 Notice ............................................................................................................................2 II. SUMMARY ........................................................................................................
I. PRODUCT INTRODUCTION 80 series printer is a POS direct thermal receipt printer with easy operation and high cost effective, which is widely used in supermarket, hospital, restaurant, bank, oil station, turnpike etc. Safety Notice Please read carefully and strict compliance with use of following instructions before operating the printer. 1.1 Warnings: Warning: Do not touch the cutter of printer.
(9) In order to ensure the printing quality and extend the life of printer, please use the recommendatory thermal paper or the one which has the same quality. (10) Please make sure the power of printer is off when plugging the connecting line. (11) Please keep the user manual for reference when needed. II.
USB Serial Ethernet Cash Drawer Power Supply Cash Drawer Control：6 lines RJ-11 socket，output: DC24V/1A ● Character ASCII code character set：12×24 dots，1.25（W）×3.00（H）mm Chinese character：24×24 dots，3.00（W）×3.00（H）mm International Code page: 10 types of international language--- PC437、 Katakana、PC850、PC860、PC863、PC865、WPC1252、 PC866、PC852、 PC858 and so on. Printing Barcode：Supports 9 types of barcode printing, UPC-A、UPC-E、 EAN(JAN)13、EAN(JAN)8、CODE39、CODABAR、ITF、CODE93、 CODE128 and so on.
(5) Please pay attention to the temperature, humidity and illumination of the storage for thermal paper. The paper would fade if the storage temperature is over 70 centigrade. 6 ● （MCBFM）Mechanical reliability: 6×10 lines ● Emulation: ESC/POS Print Font：Support ANK. The font could be magnified, bolded or underlined and the user also could adjust the character spacing before printing.
Paper roll CD Communication cable 4.2 Printer Connection (1) To ensure the printer and PC is powered off and then insert the matched data connection lines to the interfaces (USB/Parallel/Serial) of the printer, the other ends are to the PC. (2) If the user fit out the electric opened cash drawer for the printer that could insert the RJ-11 connection line of it to the corresponding interface of the printer. (PS: The specification of cash drawer should be accorded with the driver requirement of printer).
(4) Do not pull the power soft wire when unplugging. If the user does it by force, it may result in the breakdown of the printer and power adapter. 4.3 Load the Paper Roll Model: 80 printers, with easy paper loading, uses 80mm width thermal paper. The loading instruction is listed as below: (1) Open the top cover of printer. Open Button (2) Load the thermal paper into printer as the following picture. (3) Pull a part of paper out and then close the top cover.
(4) Use the cutter of printer to tear off the extra paper V. Power Switch, Keystroke and Indicator Light 5.1 Power Switch Switch is for turning on/off the power supply of printer which is located on the left. When pressing “-”, the printer turns on and when pressing “O”, it turns off. Notice: Do not turn on the switch unless the user connects the power supply. 5.
Light appears under following condition: Paperless, paper jam, print head overheat, print head error or other situations. PAPER Key（Red） ： Light appears when paperless. 5.3 Self-checking Self-checking can test whether the printer is working well or not, if it can print The test list correctly, that means the printer is good enough (which is excluding the problem with the connected interface to PC); otherwise, it needs repair.
VII. Printer Maintenance 7.1 Print Head Maintenance When the printer has following circumstances, the user should clean the print head: (1) Printing is not clear; (2) Some longitudinal columns on the printing page is vague; (3) Loud noise when feeding. Procedure of maintaining the print head is listed below: (1) Turn off the power supply and open the top cover. Remove the paper if necessary. (2) Please wait for the cooling of print head if it just finishes printing.
Procedure of maintaining the print roll is listed below: (1) Turn off the power supply and open the top cover. (2) Use the cotton cloth and dip it in the absolute ethyl alcohol to clean the surface of print roll. (3) When the absolute ethyl alcohol is completely volatilized, please close the top cover. Notice: (1) The power supply of printer should be turned off when the routine maintenance.
IX. Fault treatment When the printer appears faults, please fix them correspondingly referring to this section. If it still can’t work, please contact the distributor or manufacturer. 9.1 When indicators light on the control board is out Check whether the power wire inserts the printer, power adaptor or power socket correctly. Check whether the power switch is on or off. 9.2 The indicator light is on, while the printer can’t work Do the self-checking to check whether the printer can work normally.
FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
