USER MANUAL RP410
Catalogue Manual information .................................................................................................................. 1 Safety Instruction....................................................................................................................... 3 1. Product introduction ........................................................................................................... 5 1.1 Box list ...............................................................................
Manual information This manual includes product user, installation, etc. Please refer to the below details for all kinds of technical issues and territory. 1. Manual for driver and program. This manual includes information such as windows instruction for driver and program and main function. 2. Printer practical tools manual This manual includes usage method of option of product function, amendment of operating conditions, etc. 3. Program Manual This manual includes information of command of label printer.
FCC Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Safety Instruction Please read the following precautions to avoid personal injury or equipment damage before installing and using the printer. 1. Safety warning Warning: The print head is heating component, during printing and immediately after printing; do not touch the print head and peripheral components. Warning: Do not touch the print head and the connection plug, so as to avoid electrostatic damage to the print head. 2. Safety Precautions 1. Do not plug several products in one multi-outlet 2.
to use same power socket with large electrical machine or other can cause the power supply voltage fluctuation device. 14. Please disconnect the power of the printer power adapter, If a long time do not use the printer. 15. In order to keep good quality of printing and long life of the product, suggest to use recommended by the same quality of paper. 16. Plug or disconnect each interface, must turn off the power, Otherwise it may cause the printer control electrical damage of the road. 17.
1. Product introduction 1.1 Box list Caution： 1. open the printer packaging, keep the packaging materials, to facilitate the future of packaging and transportation 2.
1.
2. Product Specification 2.1 Specification Project Printing Storage Barcode type Detecting Function Parameters Printing method Thermal Transfer/Direct Thermal Resolution 203dpi Max printing width 104mm Printing speed 5inch/s 127mm/s (hoisting speed 150mm realizable 150mm) Interface USB 2.
Adaptor、USB cable、Power cable、CD、 Accessories user manual、Warranty Car、Certificate,、 paper tray(optional) Reliable data TPH lifespan 50km Software Operation System XP/Win7/Win8/Win10 3. Installation 3.1 Power connection 1. PLS take attention to make confirmation if the printer power button on “off” position. 2. Connect adaptor plug with printer outlet at second step. 3. Adaptor pin plug contact with power socket. 4. PLS connect the other side of the power cable to the power plug socket.
Caution： PLS make sure use our original compatible power adaptor to avoid damaging the printer. If do not using printer for an extended period, PLS disconnect it from power. 3.2 How to connect printer and PC PLS follow up below step for connecting. 1. PLS make sure the printer is off. 2. PLS contact PC and printer with communication cable like as USB/Serial/Parallel.
3.3 Install paper roll 3.3.1 Inside 1. Open fixing seat, put in paper roll with printed face above. 2. Make paper front through paper guide, pull paper exceed rubber roller, adjust paper guide to fix the paper according to the paper width.
3. Close printer cover, press down to hear “ka” to lock. 3.3.2 Outside 1. Make paper front through paper-feeding slot on the back of printer, confirm the printed face on above. 2. Open fixing seat, push up the L seat to lock.
3. Make paper front through paper guide, pull paper exceed rubber roller, adjust paper guide to fix the paper according to the paper width. 4. Close printer cover, press down to hear “ka” to lock.
3.4 The operator panel 3.4.1 The operational method of FEED printer status Operation of FEED standby press standby Press(3 seconds) Power off Open the cover Continuous printing Print pause Function Feed in a blank paper automatically Enter into the learn mode of cover sheet Hold （release after power on) Print out self test page Press 10 seconds Factory Reset press Print pause press Resume Printing 3.
3.5 Printing Test 3.5.1 Print Self-test Page When initially install printer or any problems happen to printer, you can make a self-test page to check status of firmware version, printer parameter setting, printing quality and related setting information of external equipments etc. Once you confirm printer does not have any problems after self-testing, please check other devices or software. Self-testing function is working independently with other devices and software.
Under the printer ready state, long press paper feed 3s, after the status lights (blue one) flash 2 times, release feed button. But if the printer is studying under continuous feed mode, this study will be invalid Users can also make the study from the printer tool software (see "printer setup tool instructions"). Cautions: After the completion of the study, please open the cover, roll back the blank label paper for real printing, to avoid the waste of paper. 4.
4.2 Clean the sensor, the rubber roller and paper path 1. Open the printer cover and remove the paper roll. 2. Use a dry cloth or cotton swab to wipe off dust or foreign matter. 3. Place cloth or cotton swab dipped in alcohol for medical. And use it to remove adhesive foreign substances or other contaminants. 4. DO NOT use the printer immediately after cleaning the parts.
interface; c. Printer status error; b 3.42 reference manual printer various states of LED indicator, confirm whether the printer in the standby state (green light normally on); Incorrect positioning a. No label locating a. Do label locating learning(take learning; reference of Point 3.6); b. Seam mark detection b. PLS open the cover to check sensor components the seam mark detection position offset; components position offset. c.
consistent with the paper loaded in the printer, it can be changed by setting tool; Poor print quality a. Incorrect paper a. Reloading paper(take reference loading; of Point 3.3 loading the media); b. Improper setting of b. Use setting tool or software to printing density and adjust the printer printing speed; density and speed. Setting tool c. Printer head/rubber adjusting concentration for roller has dust or coarse adjustment, drive to glue; adjust concentration for fine- d.
Bluetooth communication RP 410 printers can provide dual mode Bluetooth 4.0（SPP+BLE），it can communicate with apple 4S, ipad3, ipad4 later models. Effective communication distance less or equal 10m。 Bluetooth default pairing password: 0000, it can be setting up with parameter settings.
