XIAMEN RONGTA TECHNOLOGY CO., LTD.
Catalogue Manual information .................................................................................................................. 1 Safety Instruction....................................................................................................................... 3 1. Product introduction ........................................................................................................... 5 1.1 Box list ...............................................................................
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Manual information This manual includes product user, installation, etc. Please refer to the below details for all kinds of technical issues and territory. 1. Manual for driver and program. This manual includes information such as windows instruction for driver and program and main function. 2. Printer practical tools manual This manual includes usage method of option of product function, amendment of operating conditions, etc. 3. Program Manual This manual includes information of command of label printer.
Safety Instruction Please read the following precautions to avoid personal injury or equipment damage before installing and using the printer. 1. Safety warning Warning: The print head is heating component, during printing and immediately after printing; do not touch the print head and peripheral components. Warning: Do not touch the print head and the connection plug, so as to avoid electrostatic damage to the print head. 2. Safety Precautions 1. Do not plug several products in one multi-outlet 2.
to use same power socket with large electrical machine or other can cause the power supply voltage fluctuation device. 14. Please disconnect the power of the printer power adapter, If a long time do not use the printer. 15. In order to keep good quality of printing and long life of the product, suggest to use recommended by the same quality of paper. 16. Plug or disconnect each interface, must turn off the power, Otherwise it may cause the printer control electrical damage of the road. 17.
2.1 Specification Project Printing Storage Barcode Printing method Thermal Transfer/Direct Thermal Resolution 203dpi Max printing width 104mm Printing speed 5inch/s 127mm/s (hoisting speed 150mm realizable 150mm) Interface USB 2.
paper tray(optional) Reliable data TPH lifespan 50km Software Operation System XP/Win7/Win8/Win10 3. Installation 3.1 Power connection 1. PLS take attention to make confirmation if the printer power button on “off” position. 2. Connect adaptor plug with printer outlet at second step. 3. Adaptor pin plug contact with power socket. 4. PLS connect the other side of the power cable to the power plug socket.
damaging the printer. If do not using printer for an extended period, PLS disconnect it from power. 3.2 How to connect printer and PC PLS follow up below step for connecting. 1. PLS make sure the printer is off. 2. PLS contact PC and printer with communication cable like as USB/Serial/Parallel. 3.3 Install paper roll 3.3.
1. Open fixing seat, put in paper roll with printed face above. 2. Make paper front through paper guide, pull paper exceed rubber roller, adjust paper guide to fix the paper according to the paper width. 3. Close printer cover, press down to hear “ka” to lock.
3.3.2 Outside 1. Make paper front through paper-feeding slot on the back of printer, confirm the printed face on above. 2. Open fixing seat, push up the L seat to lock. 3.
adjust paper guide to fix the paper according to the paper width. 4. Close printer cover, press down to hear “ka” to lock. 3.
3.4.1 The operational method of FEED printer status Operation of FEED standby press standby Press(3 seconds) Power off Open the cover Continuous printing Print pause Function Feed in a blank paper automatically Enter into the learn mode of cover sheet Hold （release after power on) Print out self test page Press 10 seconds Factory Reset press Print pause press Resume Printing 3.
please check other devices or software. Self-testing function is working independently with other devices and software. Self-test page printing methods as follow: 1. Make sure printer is power linked, and paper roll installed properly. 2. Make sure is power off, and the cover is closed properly. 3. Hold the paper feed button, then press the power button; when printer is power on please loosen the feed button. 3.5.2 Use Windows Driver Programs to Print 1.
the waste of paper. 4. Clean the printer Dust, foreign matter, sticky substance or other blocking contaminants within the printer head or within the printer may lower the print quality. Follow the following methods to clean the printer head when it is dirty. ※ Note Turn off the power before cleaning the printer The printer head will be hot after printing. PLS turn off the printer and wait for 2 to 3 minutes before cleaning the printer head.
the printer head is completely dry before using the printer. ※ Clean the parts when the print quality or paper detection performance descends. 5. Troubleshooting 5.1 FAQ The contents of the table below are common problems and problem-solving methods for general operators. If you are already in accordance with our easy way to troubleshooting, but the printer still not work normally, PLS contact the manufacturer's customer service department in order to get more help.
printing the self-test page, and PLS check the driver port setting is the same as the printer; c. 3.42 reference manual printer various states of LED indicator, confirm whether the printer in the standby state (green light normally on); Incorrect positioning a. No label locating a. Do label locating learning(take learning; reference of Point 3.6); b. Seam mark detection b. PLS open the cover to check sensor components the seam mark detection position offset; components position offset. c.
printing density and adjust the printer printing speed; density and speed. Setting tool c. Printer head/rubber adjusting concentration for roller has dust or coarse adjustment, drive to glue; adjust concentration for fine- d. Printer head tuning; damaged; c. Cleaning printer head/rubber roller(take reference of Point 4.1 cleaning printer head/Point 4.2 cleaning sensor, rubber roller and paper path); d.
