E-bidet USER MANUAL
SAVE THESE INSTRUCTIONS
Contents Before use Installation and use Safety notes 1 Use precautions 4 Component description 5 Installation steps 6 Product description 10 Function introduction 11 Cleaning and maintenance 14 Other matters Faults and solutions Product dimension drawing Product technical specification Warranty Card 16 18 19 20
Safety notes Read the safety instructions carefully before use so as to properly use the product. Note the following warnings relevant to the safety. Warning Prohibition Compulsory observance Note Failure to operate pursuant to the above-mentioned warning signs may result in injury or life-threatening risk. People (including children) who are deficient in body, perception, intellectual capacity, or experience and common sense (including children) are cognized.
Safety notes Do not disassemble, repair and modify products by without authorization. May result in fire or electric shock. Please unplug the power supply when cleaning the product. May result in electric shock. 3 Please don't keep the lighted cigarette or other combustion items near the product Do not bend or twist the water supply hose. May result in water leakage. May result in fire. Do not place heavy objects on the toilet seat or the toilet cover May result product damage. Do not invert product.
Use precautions Do not place this product in direct sunlight. It may cause product discoloration and failure of seat heating function. 4 Please not use substandard power supply. Do not shower urine on the bidet body and nozzle. May cause product failure. May result in blockage. Do not lean against the toilet lid when in use May cause damage to the toilet lid. Pull off the power plug when lightning strikes. May result in product failure or damage.
Component description 1.Cover plate 2. Installation template 3.Fixation part Connecting bolt (2) Adjustment sheet (2) Plastic TAB(2) 5 Fixing plate 4.T-junction Rubber bushing(2) 5. Water inlet hose Butterfly nut(2) 6. User manual User manual Filter screen 7.Remote control 8.
6
Installation steps 4.To ensure the normal use of the product, please press reset key before installation; Note Press to maximum stroke and hold for 2 seconds 5.Slightly push the cover into fixing plate until you heard "click" , indicating that the cover has been installed in place. K CLIC 6.Close the water valve; 7.
Installation steps 8.Installation tee; inlet valve inlet valve 4 tee hose hose hose 2 hose tee angle valve Normally,the tee is installed on the angle valve 9.Open the angle vavle to check for water leakage; angle valve if the angle valve and wall is too close,you can installed the tee under the inlet valve 10.Turn on the knob to check whether the nozzle is protruding; 8 11.
Installation and pairing of remote control 1.Remote control installation Installation location: The figure shows the recommended installation location for the remote control. The installation location can be selected according to the actual use at home. Remote control bracket About 35.
Product description Toilet cover Toilet seat Nozzle Knob 10 Water supply hose joint Power socket Drain plug Disassembly button (Reset button)
11 Note
12
Cleaning and maintenance Manual cleaning of spray tube - Gently pull out the nozzle and dip the neutral detergent with a soft cloth, sponge or small brush. - Gently support the nozzle, wipe the spray tube and nozzle. Clean filter screen 2 Braided hose 14 A A Filter screen Tips: - Make sure that the corner valve close and the power off before you clean the filter screen; - Clean the filter screen when the water flow is less than normal hours.
Function description - Instructions for remote control Dryer STOP DRYER Washing mode STRENGTH MASSAGE Set light Press this key to set the lighting mode in a loop STRENGTH CHILDREN SOS LIGHT STOP Children's model*1 Press this button, star Children's mode Child lock*2 Hold this botton to lock all the remote control, hold it again can release SOS Turn on SOS.Products continuous alarm, press stop button can stop alarm Set dryer temp. Knob light on Toilet light on Set water temp.
Cleaning and maintenance Product maintenance in winter When the temperature of toilet below 0℃: -Pull out the power plug. -Remove water inlet hose from the angle valve to the toilet end, and empty the water in the water inlet hose; -Remove the bottom nut,and drain internal water. Not use in a long time When this product is not used for a long time, drain the water in the product and cut off the power supply: - Pull out the power plug. - Close angle valve and stop the water inlet.
Faults and solutions Common fault diagnosis When you think it is a fault, try some of the following processing methods. If the product is still not working properly, contact your local repair center or call the service hotline. Check power supply Check water supply 1.If power supply is under normal state. 2.Mannual reset thermostat(Istallation step4) 1.If water supply is under normal state. 2.If corner valve is closed. Note: When water leakage occurs, close the angle valve and cut off the power supply.
Faults and solutions Failure analysis of seat Phenomenon The seat is cold Possible cause The seat heating is turned off The product started the Temperature drops low temperature scald When rinsing prevention function Solution Turn on the heating function in advance After cleaning, the setting temperature will rise again Failure analysis of light Phenomenon Solution Possible cause Night light is not ON.
Product dimension drawing Product dimension drawing 18
Radio frequency specification of remote control This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.