Introduction Thank you for purchasing PUXING Series Radio. The Series radios provide cost effective communica- tions for businesses, they are the perfect communications solution for all of todays fast-paced industries. Please read this guide carefully so you know how to properly operate the radio before use.
1.CONTENTS i Cautions…………………………………………. 1 Beep setting………………………………… 10 Check equipment………………………………… 2 Channel annunciation……………………… Battery pack……………………………………… 3 Time out timer……………………………… 11 Charging…………………………………………... 4 CTCSS / DCS…………………………………... 11 Maintenance……………………………………… 5 Wide/narrow band………………………….. 11 Start……………………………………………….. 6-8 Emergency call……………………………….
02.CHECK EQUIPMENT CHECK EQUIPMENT Welcome to use our transceiver. Please check if any damage to the packing box before use. Carefully unpacks the transceiver. We recommend that you identify the items listed in the following table. If any items are missing or have been damaged during shipment, please inform the seller. SUPPLIED ACCESSORIES POW ANTENNA ADAPTOR 03.
04.CHARGING Charging Operation 04 If CHARGING the transceiver indicator displays , it means the battery pack is out of power , please charge it. Please always use the original charger. The charger’s indicator shows the charging status below. Please charge the battery pack as follow: ■Put the DC plug of the transformer into the DC socket of the charger unit. ■Connected the supplied transformer to the AC jack ■Slide the battery or the transceiver with a battery pack into the charger.
06.START INSTALL/REMOVE BATTERY The average use time of the battery pack is 10 hours. It calculated as 5% TX time, 5% RX time and 90% standby time. Don't short circuit the battery charger contacts or threw the battery into fire. case of the battery. MatchDon't the disassemble top of thethe battery pack with the corresponding grooves on the radio. Push the battery onto the bottom of the radio, buckle the safety lock. 07.
08. START INSTALL SPEAKER/MICROPHONE Insert the speaker/microphone plugs into the speaker/microphone jack. Note: The radio is not entirely waterproof when use the speaker/microphone INSTALL THE COVER OVER THE SPEAKER/MICROPHONE JACKS MIC If not use a speaker/microphone, please use the screw to install the cover over the speaker/microphone jack. 09.
10.OPERATIONS AND SETTINGS BUSY 10 CHANNEL LOCKOUT This function can prevent other two way radio from disturbing.There are two choices for customer to select in the programming software. ◆CARRIER: It is not allowed to transmit or make other operation while the radio is receiving. receiving signal, the radio is not allowed to transmit when the CTCSS/DCS different; and it is allowed to transmit if both carrier and CTCSS/DCS are the same.
12. OPERATIONS AND SETTINGS BATTERY SAVE This function can decrease power consumption when no signal is received. and no operation is perfo- rmed. You can use programming software to open or close this function. END ROGER It's prompting signal transmit finshed. You can use programming software to open or close this function. SQUELCH TALL ELIMINATION It can elimianate the end roger beep. For wearing headphone users, tail elimination is very clearly.
14. OPERATIONS AND SETTINGS side key 2 and side key 3 can be programmable. 14 OPERATIONS AND SETTINGS 1) NONE ◆No function to be set 2) MONITOR ◆If press the monitor key, it can detect if the channel is busy, it can ignore all the interference codes temporarily and receive weak signal. 3) SCAN ON/OFF ◆Scan ON: The radio will scan from the current channel. ◆Scan OFF: To press the side key again.You can exit. 4) HIGH/ LOW POWER ◆Press the key to switch High/Low Power Switch.
16. OPERATIONS AND SETTINGS Caution: 1) When use VOX by earpiece, press the PTT key to exit. 2) If use PTT/VOX earpiece, It is not allowed to switch to VOX directly during PTT call. Because it will transmit without ending. Please switch to PTT to return to normal. 17.TROUBLESHOOTING Solution Problem No Power pi Battery power dies shortly after charging ◆The battery pack may be dead.Recharge or replace it. 17 ◆The battery pack may not be installed correctly. Remove it and install it again.
18. Main technology data Main technology data Frequency Range 138-174MHz, 400-500MHz Operating Temperature -20ºC+ 55ºC Number Of Channel 16 Channel Spacing 12.5kHz Operating Voltage 7.4V DC Size 110mmX50mmX35mm(without antenna) Weight About 226.7g(with battery) Output Power <5W Modulation Distortion <=5% Spurious Radiation <=7.
interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IC Waring This device complies with Industry Canada licence-exempt RSS standard(s).
Operating Instructions: Transmit no more than the rated duty factor of 50% of the time. Push-To-Talk (PTT) button. To transmit (talk), push the To receive calls, release the PTT button. Transmitting 50% of the time, orless, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance).