Installation Instructions

ManualsBrandsXiamen Beeprt Technology ManualsComputers & AccessoriesThermal Printer

Content

Preface

Packing List

Appearance and components

Printer charging

Roll paper installation

Folding paper installation

Basic functions

Connect to the Bluetooth

Troubleshooting

Maintenance

Preface

About this manual

This manual contains information about the product and

installation. Before using the printer, please read this

manual carefully and observe the use.

International practice

Warning

For your convenience, the following symbols (icons) and

conventions are used in this manual:

This is a Class A product. In the living environment, this

product may cause radio interference. In this case, it may

be necessary for users to take practical measures against

interference.

This symbol warns that improper use may cause

property damage, serious injury or death.

This symbol indicates attention, improper use

may cause personal injury or property damage.

This mark indicates a remark, and the listed

information allows you to use this product better

or extension of lifespan.

Packing List

After unpacking the box, please check whether the

appearance of the product is intact and check all the

accessories. If there is any defect, please contact the

dealer!

Printer Manual

USB Cable

Printer Stand

Charger

Basic Function

After long pressing the power button to turn it on, short

press the menu button to enter the menu mode. In the

menu mode, short press the menu button to switch the

menu, and short press the setting button to change the

current menu item.

1、Print a test page

In the "Print yourself" menu item, short press the setting

button, the printer will print test pages by category.

2、Print density

In the “Density” menu item, you can see the current

printing density, short press the setting key, you can

switch the printing density [1-8], 1 is the lightest, 8 is the

darkest.

3、Print speed

Under the "Speed" menu item, you can see the current

printing speed, short press the setting key, you can switch

the print quality [L, M, H], L is low speed, M is medium

speed, and H is high speed.

4、Paper type

In the “Paper Type” menu item, you can see the paper

type that can be recognized for the current printing. Short

press the setting key to switch the paper type. CONTINU-

OUS is continuous paper, and GAP is gap paper.

Basic Function

6、Reset

In the "Factory Reset" menu item, press and hold the

setting key until the screen displays "Down", the printer's

parameters have been restored to the factory mode, and

some parameters will take eﬀect after restarting.

7、Bluetooth address

In the "BT MAC" menu item, user can see the Bluetooth

MAC address.

8、Firmware version

In the "Version" menu item, you can see the version

number of the printer ﬁrmware.

9、Quit

In the "Exit Setting" menu item, short press the setting key

to exit the menu and display the main interface.

5、Paper learning

In the “Paper Adapt” menu item, short press the setting

button, the printer will start feeding paper and automati-

cally learn the paper type. The printer may pause paper

feeding during the learning process, and then the printer

will feed the paper back and forth again to conﬁrm the

paper type until the menu automatically exits to indicate

the completion of the learning.

Bluetooth connection and Instructions

Instructions for Android phone

1、Printer power on.

3、Open the corresponding APP and connect to the printer

to start printing.

2、Find the Bluetooth settings in the phone’s system

settings, search for the Bluetooth device named

356Print-P3-xxxx, click to connect and enter the pairing

password as 0000 or 1234 to complete the pairing.

Instructions for iPhone

2、Open the corresponding APP and connect to the printer

to start printing.

1、Turn on Bluetooth in settings.

Note

The suﬃx "xxxx" of the Bluetooth name represents the last

four digits of the printer's Bluetooth address, which is

used to distinguish the printer.

Maintenance and Maintenance

Daily maintenance of the printer

1、Cleaning the outside of the printer and the paper

compartment: Please wipe the surface of the printer

and the inside of the paper compartment with a damp

cloth that has been wrung out. Note that the damp

cloth must be wrung out completely.

3、If you do not use the printer for a long time, please turn

it oﬀ and store it.

2、Print head cleaning: Please use absorbent cotton

dipped in absolute alcohol to gently wipe the print head

to keep it bright and clean.

Printer usage and storage

2、The printed receipts should be stored at room tempera

ture (around 20°C) and protected from light, which can

eﬀectively extend the storage time of receipts.

3、If user receipts need to be stored for a long time, please

choose long-lasting thermal printing paper.

1、Please avoid storing the newly purchased printing

paper in a place exposed to direct sunlight or high

temperature. Please do not tear the wrapping paper

when storing.

Troubleshooting

Failure

Phenomenon

Cause of Issue Solution

The screen

displays "Out of

Paper"

Place the paper

correctly and close

the paper tray

cover. Or try the

paper learning

function.

Printer is out of

paper

The screen

displays "Lid Is

Open"

Close the paper

tray cover

The paper tray

cover is not closed

properly

The printer feeds

normally but prints

blank

Reinstall the paper

in the correct

direction, or

replace the thermal

paper.

The paper is

loaded upside

down or the paper

is not thermal

paper.

Blurred print

Use alcohol cotton

to wipe the print

head to make the

print head bright

and clean.

The print head is

not cleaned

The printed

receipts are

blurred in months

or even weeks

Please use

high-quality

thermal paper and

store it at room

temperature.

The quality of the

printing paper is

poor or the

temperature of the

environment

Printer shuts down

automatically

Please charge nowLow battery

Note

Using poor quality printing paper will cause the printer to

print blurry in a short time.

Appearance and Components

Upper Lid

PaperTray

USB, Power

Paper Tray

Back Paper Tray

Push Paper, Setting Button

Printer Stand

Power, Menu Button

Screen

Open Button

Thermal Printheads

Printer Charging

Insert the charger plug into the power socket, and the

charger DC plug into the printer charging port.

AC:100V～240V(50-60Hz)

Warning

If you use a charger that is not provided or approved by

our company, The printer may be damaged.

Note

You can print while charging.

Roll Paper Installation

1、Press the open

button, open the

paper tray.

2、Remove the seal on

the printing paper

and put the paper roll

into the printer in the

direction shown in

the ﬁgure (note the

orientation of the

paper roll).

3、Align the paper with

the cutting edge and

close the paper tray.

The paper position

can be adjusted by

the paper feed

button.

Folding Paper Installation

2、Open the paper tray

and feed the folded

paper into the rear

paper inlet. The

printer will automati-

cally take in the paper

(note that the paper

should be fed inside

as much as possible).

1、Make sure that there

is no paper in the

paper tray and close

the paper compart

ment cover.

Summary of content (2 pages)

PAGE 1
Content Preface 1 Preface Packing List About this manual After unpacking the box, please check whether the appearance of the product is intact and check all the accessories. If there is any defect, please contact the dealer! Packing List 2 This manual contains information about the product and installation. Before using the printer, please read this manual carefully and observe the use.
PAGE 2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.