XGuard IntelliSwitch User’s Guide Copyright 2021 XGuard RC.
XGuard IntelliSwitch ! ! LIABILITY DISCLAIMER This device is for use exclusively on a radio controlled (RC) model. RC models are not toys. Moving parts can present a hazard to operators, bystanders and anyone or anything that could be reached by the RC model. Improper operation, maintenance or assembly can potentially cause an RC Model to pose a danger to persons or objects including but not limited to the possibility of causing serious physical injury and even death.
XGuard IntelliSwitch CONTENTS PORTS DIAGRAM...................................................................................... 4 CORRECT BATTERY CONNECTOR POLARITY.................................... 5 CONNECTION FOR HIGHER CURRENTS............................................. 6 MOUNTING THE SWITCH....................................................................... 7 LOCATOR ALARM SWITCHED ON BY RADIO SWITCH.................... 8 SWITCH OPERATION.......................................................
XGuard IntelliSwitch PORTS DIAGRAM Input Port: Red is Positive (MAX 9 Volts DC) Black is Negative (GND) Do not use higher voltage than 2S LiPo batteries. Overvoltage or Reverse voltage damage is not covered by warranty ON/OFF Pushbutton ← Output 1 & Locator Switch (TOP) ← Output 2 (BOTTOM) High-Current Output Port Buzzer/Alarm Page: 4 Page: 4 Copyright 2020 XGuard RC.
XGuard IntelliSwitch CORRECT BATTERY CONNECTOR POLARITY EC3 Connector (Not Included) Solder the wires to the connectors and slide them into the housing A) Polarity for an EC-3 Connector Positive wire (Red) Positive side of EC3 connector (Flat Side) B) Polarity for an XT60 Connector Solder the wires and add heat shrink tubbing Warning: Overvoltage or Reverse voltage damage is not covered by warranty XT60 Connector (Not Included) Positive wire (Red) Positive side of EC3 connector (Flat Side) Page: 5 Wa
XGuard IntelliSwitch CONNECTION FOR HIGHER CURRENTS Tighten the screws firmly to secure the wires to the terminal block. *WARNING* Do not use solder on the cable ends that connect into the terminal block. Connect AWG 14 wires to the screw terminal block as shown. Page: 6 Copyright 2020 XGuard RC.
XGuard IntelliSwitch MOUNTING THE SWITCH A) Double-Sided Tape Use two pads of double-sided tape 1mm or thicker on the buzzer side to attach to a clean surface of your aircraft B) Panel Mount Make sure that your panel mounting hole dimensions are at least the size of the ones in this diagram. Mount the switch using the supplied screws and carbon fiber cover plate. WARNING: Do not overtighten the screws or you will break the plastic thread. Page: 7 Add two pieces of thin doublesided tape 13mm x 6.
XGuard IntelliSwitch LOCATOR ALARM SWITCHED ON BY RADIO SWITCH Program an unused channel like AUX1 to be controlled by a switch. Use this channel to turn on or of the locator buzzer by plugging it to the top port as shown below.
XGuard IntelliSwitch SWITCH OPERATION A) WHEN BATTERY IS FIRST CONNECTED TO THE SWITCH Wait until the switch is armed and ready which is indicated by alternating blinking GREEN and RED LEDs. Once it’s armed you can click once and the switch will turn on and send power to the output ports. The selected battery mode of operation is indicated by a series of beeps from 1 to 6 depending on what is programmed as the mode of operation. If not clicked ON withing 3 seconds it will go to standby.
XGuard IntelliSwitch PROGRAMMING THE UNIT The switch comes pre-programmed from factory for 2S LiPo with audible warnings and switch active. If you want to change the settings you can program the switch for other battery types and to ignore the channel that activates the locator if so wanted.
XGuard IntelliSwitch ENTERING PROGRAMMING MODE To enter programming mode: Starting from a disconnected Battery state power-up the switch and click once the ON-button and quickly once again and hold for at least three seconds then release and listen to the musical tone that indicates program mode entered. Right away after the musical tone you will hear one beep then two beeps and so on until 6 beeps.
1 XGuard IntelliSwitch MUSICAL TONES MEANING NORMAL OPERATION: CLICK ON BOXES TO LISTEN • 1) Power UP tones (number of beeps (1-6) reflect programmed type of battery) 1 • 2) Power Down Tone (Musical tone) PLAY SOUND 2 3 4 5 6 LOW VOLTAGE WARNING TONES: • 1) Warning, battery voltage is low PLAY SOUND • 2) Emergency, battery too low do not operate aircraft.
XGuard IntelliSwitch WEIGHT Switch itself without wires:.......................12.2 grams (0.43 oz) Pair of 8 inch 14 AWG wires:...................10.9 grams (0.38 oz) Unit with wires:.........................................23.1 grams (0.81 oz) (Note: Wires can be shortened to match your specific need) INSTALLATION HOLE PATTERN Page: 13 Copyright 2020 XGuard RC.
