Certification Exhibit FCC ID: VEYCN3200R1 FCC Rule Part: 15.247 ACS Project: 14-2096 Manufacturer: xG Technology, Inc. Model: CN3200 Manual 3998 FAU Blvd.
Dual Band Routing Modem - Quick Start Guide - G7603 - Release 0.
Product features and specifications are subject to change without prior notice. xG® and xMax® are registered trademarks of xG Technology, Inc. All other trademarks used herein are property of their respective owners. For the latest product documentation and software updates, please refer to our Web site at www.xGTechnology.com/support xG Technology, Inc. 240 South Pineapple Avenue, Suite 701 Sarasota, FL 34236 (941) 953-9035 www.xGTechnology.
Table of Contents Introduction ...............................................................................................................5 About this Product ......................................................................................................5 About this Book ..........................................................................................................5 Hardware Overview ....................................................................................................
THIS PAGE INTENTIONALLY LEFT BLANK 4 Dual Band Routing Modem - Quick Start Guide - G7603 - Release 0.
The CN3200 Dual Band Routing Modem is a ruggedized subscriber device. It is waterproof and made to handle wide temperature ranges. While primarily designed for use in fixed locations, it may also be used in vehicular applications. It enables any Internet-ready device to connect to the xMax network, when paired with a WiFi access point either wirelessly or through a wired Ethernet connection. This manual provides basic instructions for installation and configuration of the CN3200 Modem.
The CN3200 Modem is a Power-over-Ethernet (PoE+) device. The IEEE 802.3at PoE+ standard enables transmission of both data and the power to operate a device over a single Cat5/5e/6 cable connection. The CN3200 Modem REQUIRES a PoE++ adaptor, as supplied. The device will NOT operate with a low-power PoE switch or adaptor. Wireless Router or PC 110-240 VAC, 50-60 Hz TO CN3200 Modem PoE++ Power Supply ETHERNET DATA POWER plus DATA 6 Dual Band Routing Modem - Quick Start Guide - G7603 - Release 0.
These notices apply to the CN3200 Dual Band Routing Modem. Be sure to read, understand and follow these instructions. Heed all warnings. Only use accessories and attachments specified by xG Technology. Keep a copy of these instructions for future reference. The CN1300 xMax 2.4 GHz Access Point MUST only be installed by a professional installer.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 25 cm (0.82 ft) between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications to this device not expressly approved by xG Technology could void the user’s authority to operate the equipment and void the product warranty.
IMPORTANT Before you begin this step, it is assumed that the CN3200 Dual Band Routing Modem has been configured as described in the CN3200 Dual Band Routing Modem Installation Guide. This was completed by the device installer. These steps connect the CN3200 Modem to an xMax network. 1. Connect the PoE++ Power Supply power cable to a 110 to 240 VAC power source. 2. If the CN3200 Modem is within range of an xMax Network, it connects within 2 minutes. 3.
When within range of a WiFi router connected to the CN3200 Dual Band Routing Modem, any Internet-ready device has the ability to securely connect to the Internet through the xMax Network. These steps connect WiFi devices to the xMax Network. 1. Configure a WiFi-enabled device for Internet Protocol Version 4 (TCP/IPv4) and DHCP operation. 2. Enter the SSID and password to match that of the user-supplied WiFi router that is connected to the CN3200. This information should have been provided by the installer.
A properly configured device, such as a PC or laptop computer, can be wired directly to the CN3200 Dual Band Routing Modem for Internet access. 1. Configure the device network interface for DHCP operation. 2. Using an Ethernet cable, connect the device to the CN3200 Dual Band Routing Modem. The CN3200 Modem can be used to create a WiFi hotspot. 1. Using an Ethernet cable, connect a WiFi router to the CN3200 Modem. 2. Configure the WiFi router according to the manufacturer instructions.
xMax RADIO Tx Power Output AVG: Receiver Sensitivity RANGE: 5 to 24 dBm in 1 dB steps -100 dBm BPSK / -90 dBm QAM64 2.4 GHz RADIO Tx Power Output AVG: Tx PowerSensitivity Output AVG: Receiver 8.5 to 21 dBm in 1 dB steps -93 dBm BPSK / -74 dBm QAM64 SYSTEM OVERVIEW Frequency Band 1: Channel size: Modulation: Spectral Efficiency: PHY Protocol: Mobility: Raw Data Rate : 904.2 to 925.8 MHz 1.44 MHz Adaptive BPSK / QPSK / QAM16 / QAM64 Up to 4.
CN3200 Dual Band Routing Modem xG Technology, Inc.
Customer is responsible for shipment to xG (or authorized service provider) and assumes all costs and risks associated with this transportation; return shipment to the Customer will be at xG’s expense. Customer shall be responsible for return shipment charges for Product returned where xG determines there is no defect ("No Defect Found"), or for Product returned that xG determines is not eligible for warranty repair. No charge will be made to customer for replacement parts for warranty repairs.
OBTAINING SERVICE AND SUPPORT UNDER WARRANTY To obtain warranty service or technical support, please contact the party from whom you purchased the product. If you purchased the product directly from xG, contact your xG Sales Representative or call 754-206-4800. To take advantage of this Limited Warranty Purchasers are required to supply an original point of purchase receipt.
THIS PAGE INTENTIONALLY LEFT BLANK 16 Dual Band Routing Modem - Quick Start Guide - G7603 - Release 0.
© Copyright xG Technology, Inc. 2014. All Rights Reserved. Dual Band Routing Modem - Quick Start Guide - G7603 - Release 0.1 xG Technology, Inc. 240 South Pineapple Avenue, Suite 701 Sarasota, FL 34236 (941) 953-9035 www.xGTechnology.
G7604 - Release 1.
Product features and specifications are subject to change without prior notice. xG® and xMax® are registered trademarks of xG Technology, Inc. All other trademarks used herein are property of their respective owners. For the latest product documentation and software updates, please refer to our Web site at www.xGTechnology.com/support xG Technology, Inc. 240 South Pineapple Avenue, Suite 701 Sarasota, FL 34236 (941) 953-9035 www.xGTechnology.
Table of Contents Introduction ...............................................................................................................5 About this Product ......................................................................................................5 About this Book ..........................................................................................................5 Before You Begin ........................................................................................................
THIS PAGE INTENTIONALLY LEFT BLANK 4 CN3200 Dual Band Routing Modem - Installation Guide - G7604 - Release 1.
The CN3200 Dual Band Routing Modem is a ruggedized subscriber device. It is waterproof and made to handle wide temperature ranges. While primarily designed for use in fixed locations, it may also be used in vehicular applications. It enables any Internet-ready device to connect to the xMax network, when paired with a WiFi access point either wirelessly or through a wired Ethernet connection. This manual provides basic instructions for installation and configuration of the CN3200 Modem.
The CN3200 Dual Band Routing Modem provides any device connected to its Ethernet port access to the xMAX network and xMax modem. When paired with a WiFi hotspot it provides access to the xMAX network to WiFi enabled devices. Alternately, any Ethernet capable device can access the network via the Ethernet port. The CN3200 Modem is totally protected against dust and moisture. The CN3200 Modem is a Power-over-Ethernet (PoE+) device. The IEEE 802.
The CN3200 Modem features seven connectors (one is unused): Four external xMax antenna connectors (N-type / female) on the base A connector for an external 2.
• • • • • • The CN3200 Modem is a 2x4 MIMO device with four antenna connectors — two Tx/Rx and two Rx-only. All connectors are always used. The CN3200 Modem is mounted directly to the back of the xMax 900 MHz panel antenna using the supplied bracket. If the recommended configuration is not used, CN3200 Modem should be placed as close as possible to the antennas for optimum performance. The antenna cable lengths should be as short as possible. The installed 2.
This is a typical tower-mounted CN3200 Modem installation with a 2x4 MIMO Panel Antenna. xMax ANTENNA IMPORTANT Install the provided eight (8) ferrite beads, as shown by this marker in the wiring diagram. 2.4 GHz ANTENNA 110-240 VAC, 50/60 Hz Tx/Rx Tx/Rx PoE++ Power Supply PoE Surge Protector Rx ETHERNET DATA POWER plus DATA Wireless Router or PC PoE Surge Protector Grounded at Building Entry 9 CN3200 Dual Band Routing Modem - Installation Guide - G7604 - Release 1.
These notices apply to the CN3200 Dual Band Routing Modem. Be sure to read, understand and follow these instructions. Heed all warnings. Only use accessories and attachments specified by xG Technology. Keep a copy of these instructions for future reference. The CN3200 Dual Band Routing Modem MUST only be installed by a professional installer.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 25 cm (0.82 ft) between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications to this device not expressly approved by xG Technology could void the user’s authority to operate the equipment and void the product warranty.
These steps set up the CN3200 Dual Band Routing Modem for use. After completing these configuration steps, the CN3200 Modem will be fully functional and ready for operation. It will broadcast on the configured channel. The CN3200 Modem will provide any Internet-ready device the ability to connect wirelessly to the xMax network, using a secure connection on a connected WiFi router. Devices may also be connected to the xMax network through a wired Ethernet connection to the CN3200 Modem.
1. Use a laptop or desktop computer to configure the CN3200 Modem. Configure the computer network adapter to Internet Protocol Version 4 (TCP/IPv4) for a static IP address and subnet mask. BEFORE YOU CONTINUE Be sure to take note of the current settings to restore them after configuration. Computer Network Adapter Settings IP Address: 169.254.90.100 Subnet Mask: 255. 255. 255.0 2. Using an Ethernet cable, connect the computer to the Ethernet connector on the CN3200 Modem. 3.
NOTE Before clicking Save Changes, be sure to write down the new settings, and then keep them in a safe place for future reference: SSID: Security Key: 8. In the Wireless Settings area, enter a unique SSID for the device. 9. Select a security protocol: 1. Click the down arrow next to Security to display a drop down menu. 2. Click the desired security protocol. The best and most secure level of security is WPA2. 3. Enter the desired security key/passphrase in the Shared Key field. 4.
This checklist may assist you in assembling the parts needed to complete the installation. CN3200 Dual Band Routing Modem SUPPLIED BY xG Technology OBTAIN FROM YOUR PART SUPPLIER CN3200 Modem with Wall Mount Bracket Ethernet Cable (Length as required) Weatherproof Ethernet Kit Grounded PoE Surge Protector (CTC Union SP-POE-01 or equivalent) PoE++ Power Supply 900 MHz Panel Antenna with mounting bracket and 4 Cables (N-Female) 2.
These steps outline the basic tasks required to complete a successful installation. Your specific steps will depend upon the requirements of your system design. These initial steps prepare the CN3200 Dual Band Routing Modem for placement in a service location. Locate the supplied CN3200 Modem mounting bracket and secure the CN3200 Modem to the bracket with 4 hex-head screws, as shown.
1. Select an appropriate location and, using the supplied U-bolt mounting bracket, lightly secure the CN3200 Modem/xMax Antenna assembly to the antenna mast. 2. Orient the antenna towards the xMax Network station and then securely tighten the nuts on the U-bolt. 3. Using the supplied bracket and hardware, lightly secure the 2.4 GHz Panel Antenna to the antenna mast. 4. Orient the antenna towards the xMax Network station and then securely tighten the nuts on the U-bolt. 5.
13. Install the supplied PoE++ Power Supply near the PoE Surge Protector. 14. Using a short Ethernet cable, connect the PoE Surge Protector to the Power plus Data (OUT) port on the PoE++ Power Supply. 15. Connect the Ethernet cable from the customer premises to the Data (IN) port on the PoE++ Power Supply. 16. Attach two ferrite cores to the PoE Surge Protector end of the Ethernet cable, as shown in the wiring diagram. 17. Attach two ferrite cores to the device end of the Ethernet cable. 18.
IMPORTANT Before you begin this step, it is assumed that the CN3200 Dual Band Routing Modem has been configured as described in the steps shown in the topic: Configuring the CN3200 Dual Band Routing Modem for the First Time on page 12. These steps connect the CN3200 Modem to an xMax network. 1. Connect the PoE++ Power Supply power cable to a 110 to 240 VAC power source. 2. If the CN3200 Modem is within range of an xMax Network, it connects within 2 minutes. 3.
When within range of a WiFi router connected to the CN3200 Dual Band Routing Modem, any Internet-ready device has the ability to securely connect to the Internet through the xMax Network. These steps connect WiFi devices to the xMax Network. 1. Configure a WiFi-enabled device for Internet Protocol Version 4 (TCP/IPv4) and DHCP operation. 2. Enter the SSID and password to match that of the user-supplied WiFi router that is connected to the CN3200.
A properly configured device, such as a PC or laptop computer, can be wired directly to the CN3200 Dual Band Routing Modem for Internet access. 1. Configure the device network interface for DHCP operation. 2. Using an Ethernet cable, connect the device to the CN3200 Dual Band Routing Modem. The CN3200 Modem can be used to create a WiFi hotspot. 1. Using an Ethernet cable, connect a WiFi router to the CN3200 Modem. 2. Configure the WiFi router according to the manufacturer instructions.
xMax RADIO Tx Power Output AVG: Receiver Sensitivity RANGE: 5 to 24 dBm in 1 dB steps -100 dBm BPSK / -90 dBm QAM64 2.4 GHz RADIO Tx Power Output AVG: Tx PowerSensitivity Output AVG: Receiver 8.5 to 21 dBm in 1 dB steps -93 dBm BPSK / -74 dBm QAM64 SYSTEM OVERVIEW Frequency Band 1: Channel size: Modulation: Spectral Efficiency: PHY Protocol: Mobility: Raw Data Rate : 904.2 to 925.8 MHz 1.44 MHz Adaptive BPSK / QPSK / QAM16 / QAM64 Up to 4.
CN3200 Dual Band Routing Modem xG Technology, Inc.
Customer is responsible for shipment to xG (or authorized service provider) and assumes all costs and risks associated with this transportation; return shipment to the Customer will be at xG’s expense. Customer shall be responsible for return shipment charges for Product returned where xG determines there is no defect ("No Defect Found"), or for Product returned that xG determines is not eligible for warranty repair. No charge will be made to customer for replacement parts for warranty repairs.
OBTAINING SERVICE AND SUPPORT UNDER WARRANTY To obtain warranty service or technical support, please contact the party from whom you purchased the product. If you purchased the product directly from xG, contact your xG Sales Representative or call 754-206-4800. To take advantage of this Limited Warranty Purchasers are required to supply an original point of purchase receipt.
THIS PAGE INTENTIONALLY LEFT BLANK 26 CN3200 Dual Band Routing Modem - Installation Guide - G7604 - Release 1.
© Copyright xG Technology, Inc. 2014. All Rights Reserved. G7604 - Release 1.0 xG Technology, Inc. 240 South Pineapple Avenue, Suite 701 Sarasota, FL 34236 (941) 953-9035 www.xGTechnology.
