XETA4-TMFA User Manual Rev.
Table of Contents Warranty ............................................................................................................................. 1 FCC Notifications ................................................................................................................. 2 Federal Communications Commission ........................................................................... 2 Integration FCC ID ...........................................................................................
Warranty XetaWave LLC warrants your XetaWave wireless data transceiver against defects in materials and manufacturing for a period of two years from the date of purchase. In the event of a product failure due to materials or workmanship, XetaWave will, at its discretion, repair or replace the product. In no event, will XetaWave LLC, its suppliers or its licensors, be liable for any damages arising from the use of or the inability to use this product.
FCC Notifications Federal Communications Commission This device complies with Title 47 CFR Part 90 of the federal code. The device complies with 47CFR § 1.1310, Table 1, Limits for General Population/Uncontrolled Exposure for MPE (maximum permissible exposure) to electromagnetic fields, when installed and operated as described herein. This device must be operated as supplied by XetaWave LLC.
WARNING This radio module shall be installed by an RF/radio professional familiar with the applicable rules. Installation of antennas shall be performed in a manner that will provide at least the MPE Distance from any user or member of the public in the direction of maximum radiation. Professional installers receive radios with factory preset settings in compliance with the values and limits specified in the radio certification.
462.7375 – 467.5375 MHz 467.7375 – 470 MHz FCC Antenna Compliance Since professional installation is required, standard RF connectors are used. Adapters or custom coaxial cables may be required to connect the radio’s RF connector to the desired antenna. Any antenna from a reputable manufacturer with desired bandwidth, gain/pattern coverage, and a rated nominal impedance of 50 ohms, can be used.
delay between radios, and other factors. For the purpose of the MPED calculation, a worst case duty cycle of 100% will be assumed, although this duty cycle is not achieved in typical operation. Integrators are responsible for including RF exposure information statements in their final user manuals. The worst case MPED for any transmit frequency in the 450 - 470 MHz band is shown in the table in the following section. FCC MPE Calculation Use: General Antenna: 11.
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This device must be operated as supplied by XetaWave LLC. Any changes or modifications made to the device without the express written approval of XetaWave LLC may void the user’s authority to operate the device. Cet appareil doit être utilisé comme fourni par XetaWave LLC.
L'étiquette extérieure utilisera le libellé: 'Contient IC: 11169A-04003’. HVIN: XETA4-TMFA IC Exposure Compliance NOTE: Integrators are required to include RF exposure information in their product user manual. REMARQUE: Les intégrateurs doivent inclure les informations d'exposition RF dans leur manuel utilisateur. Innovation, Science and Economic Development Canada MPE Calculation Required separation distance for Canada is 257 cm.
Industry Canada Antenna Compliance The antenna used for this radio must be properly installed and maintained and must provide a separation distance of at least 257 cm (101 inches) from all persons and must not be collocated or operated in conjunction with any other antenna or transmitter. Never transmit if any person is closer than the specified distance to the antenna. L’antenne utilisée pour cette radio doit être correctement installée et entretenue.
Once power is applied to the radio, the following initialization information will be displayed in the RS-232 text display window on the user’s equipment: interrupt_init timer_init crc_init() spi_init(SPI_BUS_FLASH) flash_init() mfg_cals_init() mon_init() Xetawave Bootloader revision 1.53.19108 for Xeta4 board Booting . . .
After the initialization information appears, the operating menu will be displayed. Operating Menu Operating Menu XETA4-TMFA rev 0, firmware 1.53.19108, SN E50243FC Mode: Slave (8) to Master (1) Frequency Xmit mode Recv mode Fwd power Rev power Supply Amp temp Board temp 0 1 2 3 : : : : 450006250 32QAM 51 32QAM 51 10000 11 12000 32 29 Hz Kbps Kbps mW mW mV C C Link state RSSI Noise Xmit rate Recv rate Cur success Avg success up -78 -132 22.5 0.0 100.00% 100.
Configuration/Utilities Menu XETA4-TMFA rev 0, firmware 1.53.19108, SN E50243FC Mode: Slave (2) to Master (1) 0 : 1 : 2 : 3 : 4 : 5 : Esc: Serial port configuration menu RF and hopping menu Bit rate and modulation type menu Network menu Advanced menu Utilities menu Return to previous menu Enter selection: Serial Port Configuration To modify the data serial port, enter “0” to access the Serial Port Configuration menu.
this menu. In order to successfully communicate between the radio and another device, the device’s serial port must have the same configuration as listed in this menu. In the example shown above: Baud rate is set to 115200 bps. Data bits, parity, and stop bits are given by the three characters in the Data serial framing field. In this example, there are 8 data bits, no parity, and 1 stop bit. The flow control should always be set to hardware. Options: • Enter “0” to modify the baud rate.
Data Serial Bit Rate This parameter specifies the serial bit rate in bits/second for the data port.
RF and Hopping Menu Bandwidth: 0 : 1 : 2 : 3 : 4 : c : Esc: 12500 Hz RF band Maximum separation MAS transmit power MAS master transmit frequency MAS slave transmit frequency Error correction Return to previous menu MAS band 10 km 10000 mw 460000000 Hz 465000000 Hz Disabled Enter selection: RF Configuration Menu option “0” is non-adjustable and indicates that the radio is usable only in the 406.1 – 430 MHz and 450 – 470 MHz licensed frequency range.
Transmit Power This parameter specifies the desired transmit power in milliwatts. Current value = 10000 mW Enter new value (1 - 10000) or Esc to exit: Master Transmit Frequency (“MAS master transmit frequency”) RF Configuration Menu option “3” is used to set the master transmit frequency (in Hertz) of the radio within the limits of the radio certification. If the radio is a master, then this is the frequency that it will use to transmit all messages to the slave(s).
