Specifications

ManualsBrandsXCATH ManualsElectronicsRFID Reader

RF Protocol

Document No.: XCT-RFP-EV100

Revision No.: 1

Date of revision: 2020-11-06

Summary of content (27 pages)

PAGE 1
RF Protocol Document No.: XCT-RFP-EV100 Revision No.
PAGE 2
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) Contents Specification ··································································································· 3 Configuration of IS-4500C1 ················································································ 3 2.1 Connect ········································································································ 3 2.
PAGE 3
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev.
PAGE 4
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) Specification Category RF Frequency Power Supply Supply Current Dimensions RF Protocol Host Interface Antenna RF Power Read Range Anticollision Contents 13.56MHz 4.5 to 5.5V DV Operation 40mA @ 5V 43*35*6 mm ISO 14443-A TTL232, USB To Serial(FTDI USB Chip) 50-ohm Internal antenna 150mW @ 5V 50mm internal ant Support(1tags) ⚫ The RFID Reader is used after being mounted inside the equipment. Configuration of IS-4500C1 2.
PAGE 5
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) • PCB Bottom 2.2 USB Driver HID USB KeyBoard o Automatically recognized without the need for driver installation. USB To Serial Driver o USB Chip : FTDI230x o Download site : http://www.ftdichip.com/Drivers/VCP.
PAGE 6
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev.
PAGE 7
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) Usage of ISReaderPro V3.0 Enable NTAG. Authenticate NTAG. Change the value of the authentication key for the NTAG. Retrieves block data from NTAG (16 bytes) Write block data from NTAG. (4Byte) Write the 16 Byte size to the NTAG at once. Check the version and type of NTAG. Reads the Sign ECC value of the NTAG.
PAGE 8
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) Enter the block address to set up protection. - Available after authentication processing. You can set the AUTH0 block data Write/Read Protect. - (2) Can be used after authentication processing - See the NTAG datasheet for more information. You can view the current AUTH0 block address and Write/Read Protect settings information. - Available after authentication processing. Reads the 24 Bit Counter value. You can enable and disable the 24 Bit Counter.
PAGE 9
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) Protocol Format 5.1 Request (Target , PC → IS-4500C1) ITEM BYTE STX 1 0x01 Hex Start Data Command1 1 Command Hex High rang command Command2 1 Command Hex Low rank command Hi Byte Hex Low Byte Hex Data Length Data Length 2 DESC REMARK Packet Lens Data N Hex Request Data Check Sum 1 Hex See “Check method” ETX 1 Hex End Data 03 Sum calculation A buzzer beep command when successful after Command2 is performed.
PAGE 10
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev.
PAGE 11
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) Protocol (NTAG) 7.1 NTAG Active Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x20 Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 12
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.3 NTAG Authenticate Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x30 Hex 0x00 Hex 0x04 Hex Data Length Data Length 2 Packet Lens Data 4 Hex Authenticate Key Value Check Sum 1 Hex See “Check Sum calculation method” ETX 1 Hex End Data 03 7.
PAGE 13
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.5 NTAG Authenticate Key Value Change Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x3B Hex 0x00 Hex 0x04 Hex Data Length Data Length 2 Packet Lens Data 4 Hex Authenticate Key Value Check Sum 1 Hex See “Check Sum calculation method” ETX 1 Hex End Data 03 7.
PAGE 14
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.7 NTAG Block Read 16 Byte Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x22 Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 15
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.9 NTAG Block Read 4 Byte Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x22 Hex 0x00 Hex 0x02 Hex Data Length Data Length 2 Packet Lens Data 1 Hex Start Block Address Data 1 Hex End Block Address Check Sum 1 Hex See “Check Sum calculation method” ETX 1 Hex End Data 03 7.
PAGE 16
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.11 NTAG Block Write 4 Byte Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x23 Hex 0x00 Hex 0x04 Hex Data Length Data Length 2 Packet Lens Data 4 Hex Block Data Check Sum 1 Hex See “Check Sum calculation method” ETX 1 Hex End Data 03 7.
PAGE 17
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.13 NTAG Block Write 16 Byte Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x23 Hex 0x00 Hex 0x10 Hex Data Length Data Length 2 Packet Lens Data 16 Hex Block Data Check Sum 1 Hex See “Check Sum calculation method” ETX 1 Hex End Data 03 7.
PAGE 18
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.15 Version Read Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x32 Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 19
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.17 Sign ECC Read Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x33 Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 20
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.19 AUTH0 Write Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x35 Hex 0x00 Hex 0x01 Hex Data Length Data Length 2 Packet Lens Data 1 Hex AUTH0 Data Check Sum 1 Hex See “Check Sum calculation method” ETX 1 Hex End Data 03 7.
PAGE 21
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.21 Access Protect Write Request (Target , PC → IS-4500C1) ITEM BYTE DESC STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x35 Hex STATE 1 0x01, 0xFF Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 REMARK 0x01 : success 0xFF : failure Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 22
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.23 AUTH0, Access Protect State Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x37 Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 23
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.25 24Bit Read Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x31 Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 24
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.27 24bit Enable Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x38 Hex 0x00 Hex 0x01 Hex 0x00, 0x01 Hex Data Length Data Length 2 Packet Lens 0x00 : Disable Data 1 Check Sum 1 ETX 1 03 0x01 : Enable Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 25
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.29 24bit Protect Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x38 Hex 0x00 Hex 0x01 Hex 0x00, 0x01 Hex Data Length Data Length 2 Packet Lens 0x00 : Protect Disable Data 1 Check Sum 1 ETX 1 03 0x01 : Protect Enable Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 26
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) 7.31 NTAG 24bit Counter Enable, Protect State Request (Target , PC → IS-4500C1) ITEM BYTE DESC REMARK STX 1 0x01 Hex Start Data Command 1 1 0x05 Hex 0x05 : NTAG, Ultralight Command Command 2 1 0x3A Hex 0x00 Hex 0x00 Hex Data Length Data Length 2 Check Sum 1 ETX 1 03 Packet Lens Hex See “Check Sum calculation method” Hex End Data 7.
PAGE 27
Title: RF Protocol Doc.#: XCT-RFP-EV100 (Rev. 1) Related Document • IS-4500C1-Reader-NTAG_Manual (IKSUNG ELECTRONICS) 9. FCC Statement and User Information • This module satisfies the Part15C rule, and when integrated into the host, it must be verified that it meets the Part 15B standard. • This device complies with part 15 of the FCC Rules.