AT-iMG634 – R2 USER MANUAL
AT-iMG634 – R2 User Manual This User Manual covers the following product: AT-iMG634 – R2 For a description of detailed functionality please refer to the Reference Manual. For installation and safety instructions please refer to this User Manual. 613-000480_A Copyright © 2008 Allied Telesis Holding K.K. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis.
1 IMPORTANT SAFETY INSTRUCTIONS DO NOT OPEN the product, remove screws or cover. To prevent ELECTRIC SHOCK during normal use, the plastic chassis of the product must be kept closed. This unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified technician. DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING ACTIVITY to avoid ELECTRIC SHOCK. Do not use the telephone to report a gas leak in the vicinity of the leak.
This could lead to fire or electric shock. Take care when handling the power cable and plug: • Do not strain the power cable • Do not place near a heater or stove • Unplug the power cable using the plug Keep the product free away from dust and maintain it clean. Unplug before cleaning. Only the power adapter supplied with this unit is guaranteed to function correctly with it. Do not drop the unit, handle with care. If really dirt, clean using a soft, damp cloth with a neutral detergent.
3 CONTENTS OF THE PACKAGE The following items are included in the package. Contact your sales representative if any items are damaged or missing. 1. One AT-iMG634 – R2A or AT-iMG634 – R2B 2. One AC/DC power adapter 3. One CD user manual Power Adapter AT-iMG634WA/B CD User Manual PLEASE NOTE THAT THE PACKAGE DOES NOT CONTAIN SCREWS.
4 PRODUCT DETAILS Top view of unit WLAN Tel 1 Tel 2 PPP ADSL LAN Power/System Rear view of unit Antenna POWER (AT-iMG634W Only) LAN ADSL Tel
LED description Led Power/ System PPP LAN WLAN ADSL State Green light on The device is receiving power; voltage is within the acceptable range Red light on temporarily after power on Boot phase Red light on continuous An abnormal operating condition Red light flashing Software upgrade in progress Red light off The system is working normally Green light on PPP Link up Red light off No PPP link established Left Green light on Link up Left Green light off Link down Left Green light fla
Rear panel ports and button description Function Tel Port Connects analog telephone and fax through a telephone cord Used to reset the unit; it causes the default configuration to be loaded with the static IP address value of 192.168.1.1. Default Button To reset, press the ‘default’ reset button through the ‘default’ hole. Then power the unit while keeping the button pressed. When the system red light flashes to signal the starting of boot phase, wait another 15 seconds and then release the button.
5 UNIT INSTALLATION
6 CONNECTING THE AT-IMG634 – R2 ADSL cable connection Plug the ADSL cable into the ADSL port until you hear a “click” and make sure it is correctly fixed by lightly pulling the ADSL cable. In the same way, Connect the plug on the other end of the ADSL cable to the terminator. LAN Cable connection Push in the plug of the UTP cable to the LAN port until you hear a “click” and make sure it is correctly fixed by lightly pulling the UTP cable.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Appendix - Technical Specifications Interface ADSL port LAN port TEL port WiFi 1 ADSL (6 pin RJ11 connector for Annex A, 8 pin RJ45 connector for Annex B) 4 10/100BASE-TX (8 pin RJ45 connector) 2 FXS (6pin RJ11 connector) 802.11b/g Power Input voltage DC input current Average power 12V DC 1.25A (DC 12V) 12.