User's Manual

ManualsBrandsXanboo ManualsElectronicsZIGBEE DOOR SENSOR

PRODUCT MANUAL

TITLE:

ZIGBEE DOOR QC101500

REVISION:

1.0

DATE:

3/17/08

ZigbeeDoor QC101500.doc 3/17/08 Page 1 of 5

Created by Marc Lindahl Last saved by Marc Lindahl

Created on 1/15/08 3:31 PM

Product Description

The Zigbee Door Sensor is a magnetic contact sensor. The Door/Window Sensor uses a

magnet to enable you to monitor the opening or closing of a door, window, cabinet, or

whatever else needs to be checked for movement.

How It Works

The sensor monitors the status of the magnetic contact.

When a change is detected with an opening or closing of

a monitored door or window because the magnet is too

far away or close by, the sensor sends a notice of the

event via Zigbee. The sensor can detect the magnet on

the left, right, or top side.

Installation

- Please familiarize yourself with the concepts of Zigbee Networking with the

“Understanding Sensor Networking” paper.

- The network Coordinator and any Routers must be set up before setting up this

sensor.

- Open the battery compartment and pull out the battery activation tab. The blue

LED should flash briefly indicating successful power up. Close up the unit.

Sensor Mounting

Please consider the following points when mounting the sensor:

 The Door/Window Sensor is constructed of UV resistant ABS plastic allowing for

indoor or outdoor use.

 The Door/Window Sensor is constructed of UV-resistant ABS plastic. If installing

the Wireless Door/Window Sensor outside, it should be shielded from the elements,

such as underneath a porch roof. Do not install the sensor where it is subjected

directly to the elements.

 Typically, the sensor's wireless reception is good to up to 250 feet from the zlosese

Zigbee Router, depending on indoor or outdoor use and the number of obstacles.

These can include metal framing, thick walls, etc. It is recommended that different

positions be tried for optimal results.

Summary of content (5 pages)

PAGE 1
PRODUCT MANUAL TITLE: REVISION: ZIGBEE DOOR QC101500 1.0 DATE: 3/17/08 Product Description The Zigbee Door Sensor is a magnetic contact sensor. The Door/Window Sensor uses a magnet to enable you to monitor the opening or closing of a door, window, cabinet, or whatever else needs to be checked for movement. How It Works The sensor monitors the status of the magnetic contact.
PAGE 2
ZIGBEE DOOR QC101500 1.0 The spacing between the sensor and the contact should be between 1/10 inch and ½ inch (.25 cm to 1.27 cm). Mount Your Door/Window Sensor 1. Mount Your Door/Window Sensor . The easiest way is to use the double sided foam tape supplied with the sensor. Make sure the contact area is clean and dry and apply pressure on the tape for at least 30 seconds. You can also mount the sensor more securely using the screws in the hardware kit.
PAGE 3
ZIGBEE DOOR QC101500 1.0 Operation In normal operation the user need not interact with the occupancy detector, as it is normally controlled remotely via Zigbee and automatically calibrates itself. Changing batteries The device uses standard AAA alkaline batteries. Always replace both batteries at the same time. Always use fresh new batteries of the same brand. The battery compartment is exposed by twisting a quarter in the slot at the end of the case, and then pulling apart.
PAGE 4
ZIGBEE DOOR QC101500 1.0 Zigbee Profile sample profile for a ZigbeeDoor device: freq bits: 0x8 caps bits: 0x0 repeatFilter: 1 mfg code: 0x1038 xfersiz: 0x0 bufsiz: 0x50 powersource: 0x4 user descr: QC101500 v0.1 last LQI: 117 avg LQI: 116.886977 powersources: 0x4 APS flags: 0x0 powerlevel: 0xc IEEE addr: 0x1d400000400000 user desc. avail: 0x1 registered: 0 servermask bits: 0x0 type bits: 0x2 complex desc.
PAGE 5
1.0 ZIGBEE DOOR QC101500 Block diagram Approvals FCC ID OU4-QC101500 / IC: 4576A-QC101500 INSTRUCTIONS TO THE USER: The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.