d TERMINAL PAYMENT DEVICE XCL_AT-100 SERIES INSTALLATION GUIDE xCL_AT-100 series: - xCL_AT-100-R3-18U xCL_AT-100-R3-18E
1 This symbol is intended to alert the user before starting using the POS. Before using the Device. Please do the full charge (0% ~ 100%) once to get the best battery performance. Please ensure the unit was not stored for over one month without charging. Battery life will depend on different use-cases and the battery manufacturer recommends replacing it with a new one every 2 years. Caution: Do not attempt to open and disassemble the device, that will cause device tamper. 1.
FRONT AREA REAR AREA 1 Printer Paper Cover 2 4” Display 3 Magnetic Strip Reader (MSR) slot 4 Power Button (Press > 3 seconds to power on/off) 5 Smart Card Reader (SCR) slot 6 Charging contact points 7 USB port (type C) for charging 8 Camera for 1D/2D barcode scanning (Optional) 9 Battery Compartment ■ AT-100 Power spec: Input: 5V DC, 2A ■ Power Adapter spec: Input: 100 ~240 Vac Output: 5V DC, 2A Caution: Use only the AC adapter approved and provided by XAC Automation Corporation for use
. USING THE MAGNETIC CARD READER Swipe the card through the slot with magnetic stripe side facing the same direction as the display. (Figure 3) Figure 3 5. USING THE IC CARD READER Insert an IC card into the slot (Figure 4) with the chip side facing the same direction as the touch panel (Figure 5).
6. USING THE KEY PAD After inserting the chip card, Press the numeric key as below keypad (Figure 6) to enter the desirable numbers. Press Cancel (X) key to terminate any current function and press the Enter (O) key to confirm a value or an option. Figure 6 7. USING THE CONTACTLESS CARD READER Tap the contactless card on top of the contactless logo (Figure 7).
8. REPLACE THE BATTERY 8-1 REMOVE THE BATTERY STEP 1: Push the latch to pull the battery cover from AT-100 as Figure 8. STEP 2: After removing the battery cover, pull up the battery connector as below Figure 9 to change a new battery. Figure 8 Figure 9 8-2 INSTALL THE BATTERY STEP 1: Insert the battery connector into AT100 with correct direction as Figure 10. STEP 2: After install the battery, close the bottom cover as Figure 11.
Bottom Cover Removal Warning When removing the bottom cover and screws for the purposes of changing battery, remember to put back the cover and screws before power on the POS. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Warning for internal battery pack To reduce risk of fire or burns: 1. Do not attempt to open, disassemble, or service the battery pack. 2.
10. LOADING THE PAPER Gently pop the printer cover’s latch; then pull the cover (Figure 13). Load a roll of thermal paper into the printer. Load it so that the print-side of the paper will feed out facing the operator. Close the cover by pressing on the center of the printer cover. Use the serrated bar to tear off any excess paper.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT (Only for xCL_AT-100-R3-18U) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
XAC Automation Corporation 886-3-577-2738 www.xac.com.tw The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed, distributed or reproduced without permission of XAC Automation Corporation. XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of his material.