Operation Menu Version: 1.
Operation Menu FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Operation Menu Content 1. Power on 1 2. Mode button 2 3. User button 3 4. HTTP control panel 4 5.
Operation Menu 1. Power on There are three working modes after power on. Maintenance: The device is connected using the USB interface to a PC with specific software named NandPDT to perform firmware update, reset to factory operation to adjust/debug its behavior. This mode is activated by pushing the “Mode” button for 10 seconds with the USB plugged in to a computer. Please refer to section 5. Firmware upgrade.
Operation Menu 2. Mode button Pressing 1 second to turn the device to set the WiFi to be managed mode and try to establish a new link with WiFi AP named SBMAMA, the name/SSID of WiFi AP can be configured by field of SSID on HTTP control panel. If it failed to establish a link with the AP within 30 seconds, then it will switch to ad-hoc mode with SSID SBMAMA. Pressing the Mode button for 1 second will turn the device back to managed mode again.
Operation Menu 3. User button User button will act multifunction and its role is configured by HTTP control panel. Default to disable. Disable : the User button will be no function, no response to any touch. User Off : the photo frame backlight will turned off once the User button was touched, and keep it off as long as hours defined by the value of UserOff parameter on HTTP control panel.
Operation Menu 4. HTTP control panel Open the device HTTP control panel by http://the.device.ip.address on browser like Microsoft Internet Explorer. 4.1 System Parameters FW_Version A display only data field shows the firmware version on photo frame. Active_Mode A display only data field shows the active mode on photo frame. There are install, Operating and Maintenance modes. Networking_Mode A display only data field shows the Networking mode on photo frame.
Operation Menu 4.2 Networking Parameters IP_Select Radio buttons allow users to set IP address on either Auto (DHCP client) or Specific (Fix IP). Default to Auto mode. IP_Addr Text edit field allows users to set IP address under Specific IP mode, in format of xxx.xxx.xxx.xxx Mask Text edit field allows users to set Mask under Specific IP mode, in format of xxx.xxx.xxx.xxx Gateway Text edit field allows users to set Gateway address under Specific IP mode, in format of xxx.xxx.xxx.
Operation Menu Encryption Radio buttons allow users to select the encryption method on WPA and WPA2 mode. There are method TKIP and AES. Default to TKIP. Press Submit button to update the parameters to photo frame. 4.3 RSS parameters Sync_Policy Radio buttons allow users to select the RSS synchronization policy, on either Once or Online. User_button Radio buttons allow users to select the function on User Button. There are Disable, User Off, Select Feed, and Interaction modes. Default to Disable.
Operation Menu effect between slideshows. There are Random, Top down, Bottom up, Horizontal close, Horizontal open, Random Horizontal lines, Forward brick fill, Random brick fill, Backward brick fill, Whirlpool, Wave, Left to right, Right to left, Vertical close, Vertical open, Random vertical lines, Meet, Fade out and in and Fade in and out effects. Default to Fade in and out. Current_Feed_URL A display only data field shows the current Feed URL.
Operation Menu 5. Specification Specification Item Description 10.4inch LCD Type Digital TFT-LCD Support Color Full-colors Display Resolution Screen Ratio 800x600 4:3 Certification & Safety CE, FCC, RoHS Compliance Main Chip Type Operation System System Linux SDRAM 64MB(Byte) ARM11 System Internal Memory NAND Flash ROM WiFi 1GB optional(11n/g/b) Networking RJ-45 connection USB 2.0 Port – Host (For F/W upgrade) Type-A supported supported AC/DC Power Adapter:100~240V DC 5.3V/2.