Quick Start Guide

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority
to operate the equipment.
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates
uses and can radiate radio frequency
energy and, if not installed and used in
FCC Statement IC Statement
Sensors
Red light
Sensor triggered
Wyze Sense Starter Kit
QUICK START GUIDE
IN THE BOX
Wyze Contact Sensor
(battery pre-installed)
Wyze Motion Sensor
(battery pre-installed)
Wyze Sensor Bridge
Quick Start Guide
Pin
x2
x1
x1
x1
x1
Wyze Sensor Bridge
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
-- Reorient or relocate the receiving
antenna.
-- Increase the separation between the
equipment and receiver.
-- Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced
radio/TV technician for help
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions (1)this device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
This device complies with Industry
Canada’s licence-exempt RSSs. Operation
is subject to the following two conditions:
(1) This device may not cause interference;
(2) This device must accept any
interference, including interference that
may cause undesired operation of the
device.
The term “IC: “ before the certification/reg-
istration number only signifies that the
Industry Canada technical specifications
were met. This product meets the
applicable Industry Canada technical
specifications.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicable aux
appareils radio exempts de licence.
L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement
STATUS LIGHT
Bridge
Solid yellow light
The Bridge is powered on, but
not connected. Remove the
Bridge, make sure the camera is
online, has the latest firmware,
and then reinsert the Bridge.
Flashing yellow/blue light
The Bridge is trying to connect. If
NEED MORE HELP?
Resources & Support
support.wyze.com
Community
forums.wyze.com
Wyze Motion Sensor
Wyze Contact Sensor
TROUBLESHOOTING
The Sensor Bridge isn’t connecting
Ensure your camera is online, has a
stable connection, and the latest
firmware. If problems persist, remove
it doesn’t turn solid blue after
several minutes check to ensure
your camera is online and has
the latest firmware. Remove the
Bridge, wait for camera
connection to be stable, then
reinsert the Bridge.
Solid blue light
The Bridge is working properly.
Flashing blue light
The Bridge is pairing to a sensor.
1 2 3 4
11 12 13 14
15 16 18 19
10
17
Pin
SETUP
1
Ensure your Wyze Cam or Wyze
Cam Pan is setup, online, and has
the most updated firmware.
5
CONTACT SENSOR
PLACEMENT
Ensure the two sections of the Contact
Sensor are at most 2 cm apart when closed.
2cm(max.)
2
Insert the Sensor Bridge into the
USB port of a Wyze Cam or Wyze
Cam Pan and wait for the Status
Light to turn solid blue.
3
Open the Wyze app and tap the
3 dots on the top right corner of
the Home Page. Select “Add a
Product” and then select the
Sensor type you want to setup
first. Follow the instructions in
the Wyze app to finish setup.
POWER
Wyze Sensor Bridge
4
Repeat Step 3 for each Contact
and Motion Sensor.
6 7 8
MOTION SENSOR
PLACEMENT
Place Sensor approximately 6 feet high and
ensure the Wyze Logo is in the top left corner.
9
the Bridge from your camera, wait 30
seconds, and then reinsert into the
camera.
A sensor won’t connect to the Bridge
Ensure the Bridge is solid or flashing
blue and the camera has a stable
connection. If problems persist, try
moving the camera closer to the
sensor (we recommend sensors are
placed on the same floor as the
Bridge).
A sensor isn’t working properly
Ensure your camera is online and has
a stable connection. Replace the
sensor’s battery if its status light
doesn’t blink when triggered.
( WHCS1)
( WHMS1)
( WHSB1)