WyreStorm 4x4 Quick-Install Matrix/receiver pack (Version 2.0) 4 Input / 4 Output single-cable HD Matrix with IR Source control Part Number MX-0404-QI 4 x Single Cat5e/6/7 40m (131ft) HD Receiver supporting HDMI and IR Source control Part Number RX-1UTP-IR-40 Instruction Manual Thank you for choosing this WyreStorm product. Please read these instructions carefully before installing to avoid complications later.
CONTENTS AND INTRODUCTION Contents 1 Introduction 2 Features i. MX0404-QI ii. RX-1UTP-IR-40 3 Safety Precautions 4 Package Contents 5 Specification i. MX0404-QI ii. RX-1UTP-IR-40 6 MX0404-QI Panel Description 7 RX-1UTP-IR-40 Panel Description 8 Typical Application 9 Connection 10 Basic Operation 11 Advanced Operation i. IR Call-back and Third Party Control Systems ii. RS232 Control iii. COM CTL iv. LAN Control – NET CTL v. MX0404-QI - EDID DIP Switch settings vi.
• Protection against ESD (electrostatic discharge) included within the unit to further stabilise transmission. • LED indications for clear power and video signal selection. 2. MX0404-QI Features • Quick and easy installation – set up in seconds straight out of the box. • Simplified ports - Input: HDMI – Output: integrated RJ45 connectors for a single Cat5e/6/7 UTP cable to each display point for ease of installation.
PACKAGE CONTENTS AND SPECIFICATION 4. Package Contents • 1 x MX0404-QI main unit • 1 x Printed instruction manual • 1 x Flash USB stick containing PC software and digital copy of instruction manual. Digital copy also downloadable from www.wyrestorm.com • 1 x Matrix mounting brackets (pair) • 1 x 12VDC power supply • 1 x IR Extension cable (IR RX) • 4 x IR TX Emitters (small for Input source) • 1 x MX0404-QI remote control incl.
MX0404-QI - Panel Description FRONT REAR 1 1 2 3 4 5 Mounting Brackets 2 Input select button (click to scroll numerically) Input selection per output (click to scroll numerically) 3 4 IR Receiver port (IR RX) 5 AC100 – 240V power input 6 7 8 PANEL DESCRIPTIONS 6.
TPYICAL APPLICATION 8.
01 Connection HDMI Source 02 Control System Additional control via RS232 12v DC power 03 IR TX jack plugged in to IR TX port of Matrix Screen MX0404-QI KEY LAN IR TX emitter placed over or near infrared sensor 04 08 Cat5e/6/7 up to 40m (131ft) IRTX Emitter IRRX Receiver 05 HDMI OUT MIN LAN MA X EQ UTP Cat5e/6/7 DIS TANC E HDMI 5v DC power 07 P /N:R X-QI-IR -40 RX-1UTP-IR-40 1 Connect your HDMI input sources (such as: HDDVD,PS3/, XBOX360, satelClass B/cable, Blu-Ray etc.
BASIC OPERATION Switch on the power to your input sources, displays, and any display receivers used. Finally, power up the MATRIX. Your MX0404-QI should now be fully connected and ready for use. Remember, always switch off the matrix before unplugging any inputs or outputs – follow last on, first off protocol. If there is electrical interference or cable bends/kinks within the set up the IR is one of the first functions to fail.
The MX0404-QI is not only a switcher and extender of multiple HDMI signals to multiple HDMI receivers located remotely, it also passes IR control signals through the IR call-back system to the matrix and HDMI sources for full, independent control of all connected inputs from output locations using your remote handset.
ADVANCED OPERATION HINT If problems are encountered controlling devices remotely, check IR TX Emitters and IR RX Receivers are correctly positioned and connected to sources, displays and display receivers, with all devices fully powered and the matrix set to IR callback enabled and IR TX Switch mode activated. See COM CTL section for Call-back enabling.
ADVANCED OPERATION 9 6 7 8 1 2 3 4 5 1 Receive Message Window – displays messages received from the matrix, such as input/output settings and command selections. You can view the current condition of all input/output ports by pressing the button. Pressing will delete the previous message received in the window.
ADVANCED OPERATION • Connected to ENABLE matrix communication • Disconnected to DISABLE matrix communication 4 Com Select 5 Connect/Disconnect 3 to manually input the IP address. 4 Click to complete the process or Click the Com Select dropdown to see all Com ports available. Select your chosen Com port number and press the CONNECT button. You will notice the button change to show ‘disconnect’ and CONNECT STATE change to green for ‘connected’.
ADVANCED OPERATION current settings of the IR Matrix viewable by pressing the button 4 9 Input/Output Switch – Switches connected inputs per output. COM CTL Input/Output selection Operation as with remote control handset – select the chosen input to be displayed on each output by either clicking the left/right arrow buttons to scroll through inputs numerically, or pressing the input number 1-4.
ADVANCED OPERATION Double click on the device name/default factory serial number (or right click and OPEN) and you will be directed to a web login page in your internet browser. Press the button to update your chosen matrix settings into the left hand display and your selection to take effect. B The lower section of the NETCTL controller screen is dedicated to IR Matrix settings.
ADVANCED OPERATION Click to assign the new IP address to the system and you will return to the previous screen or to return without changes taking effect. Now click for the Matrix to detect the new IP address, which will appear in the dialog box. Finally click to confirm IP settings Attention This ‘Assign IP’ process differs from the COM CTL ‘IP Set’ function. ‘Set IP’ in COMCTL saves/reads the IP address in flash and sets it as static IP.
1080p 5.1 Audio (using embedded D-series EDID) ADVANCED OPERATION When set to this DIP position the matrix will use embedded 1080p video with 5.1ch Audio. After setting the DIP switch, reconnect and turn on for EDID settings to take effect. 1080p 7.1ch Audio (using embedded G-series EDID) When set to this DIP position the matrix will use embedded 1080p video with 7.1ch Audio. After setting the DIP switch, reconnect and turn on for EDID settings to take effect.
Generally, the majority of HD distribution installation issues are either caused by minor connection errors, communication problems between devices, or when the transmission of high signal bandwidth is attempted using insufficient cable. Should you encounter any technical difficulties when installing and configuring the matrix, we are confident solutions can be found by working through the following troubleshooting checklist before seeking alternative technical support.
TROUBLESHOOTING terminations or excessive cable lengths. Try swapping the display adaptors from a location you know is functioning properly or swapping the outputs of the matrix switch used. If the problem remains on the same screen this may be caused by a connection problem between matrix and display – turn off all equipment and swap the signal carrying cables at both ends to ascertain if the cable or termination is at fault.
5) UTP Termination Issues - swap cables over at both transmitter and receiver ends to see if control is established. If so, a possible re-termination of the cable could remedy the problem. 6) Are you using WyreStorm emitters and receivers? The use of third party products/magic eyes may not be compatible. Always use WyreStorm components included with your purchase or check compatibility of third party control systems with your WyreStorm dealer.
MAINTENANCE, PROVIDED SERVICE AND MAIL-IN-SERVICE in generations 1.3, 1.4 etc. • STANDARD (or “category 1”) HDMI cables perform at speeds of 75Mhz or up to 6.75Gbps, which is the equivalent to a 720p/1080i signal. • All WyreStorm equipment support HIGH-SPEED (or “category 2”) HDMI cables that have been tested to perform at speeds of 340Mhz or up to 10.
Warranty Should you feel your product does not function adequately due to defects in materials or workmanship, we (referred to as “the warrantor”) will, for the length of the period indicated below (starting from the original date of purchase) either: a) Repair the product with new or refurbished parts. or b) Replace it with a new or refurbished product. Limited warranty period: All WyreStorm products are covered by a 2 year PARTS and LABOUR warranty.
INSTALLATION NOTES 18. Installation Notes WyreStorm MX0404-QI Installation Reference Log (INPUT) INPUT Input number on Matrix Source Location Source Details Source resolution & audio settings Cable Number 1 2 3 4 22 Technical Support: support@wyrestorm.
OUTPUT Output number on Matrix Output Location Display Details Display Resolution & Audio Settings Cable Number 1 2 3 4 Technical Support: support@wyrestorm.
www.wyrestorm.com WyreStorm Offices US Office: 6991 Appling Farms Parkway, Suite 104, Memphis, TN 38133 Tel: + 901 384 3575 Fax: + 901 384 3574 Unit 22, Ergo Business Park, Swindon, Wiltshire, SN3 3JW UK Tel: +44 (0) 1793 230 343 Fax: +44 (0) 1793 230 583 WyreStorm Technical Support US: +86 6677 0053 UK:- +44 (0) 1793 238 338 Email: support@wyrestorm.com We reserve the right to change specification or product dimensions at any time.
