Thank you for choosing Wu loo! The driveway alarm is one of our latest products.
1. What’s included in the box? 1.1 Sensor overview 1.2 Receiver overview 2. Getting Started 2.1 Connect with power 2.2 Setting the Sensitivity&Channel of sensor 2.3 Pairing 2.4 Charge for sensor 2.5 Installing the sensor(test before installing) 2.6 Setting the receiver 2.7 Usage Scenario 2.8 Notes 3. Advanced Settings 3.1 Volume Setting 3.2 Mute Mode 3.3 Melodies Setting 3.4 Time&Alarm Setting 3.5 Pairing 3.6 Power&Charge 3.6.1 Charge Sensor 3.6.2 Receiver connect with the power 4. Additional Notes 5.
at’ s included in box? 4x Small Screws & Screwdriver Blg Craws & Anchors AG Adapter & Cable 1.1 Sensor overview This sensor is designed for outdoor use. The sensor remains in sleeping mode throughout most of the day and is activated when it detects movement. The sensor’s eye will display a red light and send a signal to the receiver when it has been activated. Once the receiver obtains this signal, it will ring and light up to alert you to the detected motion.
— Sensitivity nestling Power port switch Ballpoint Shanna) chatting (Angle adjustment) switch i Mounting plate ON/OFF button (Click it by included screwdriver) 1.Setting the sensitivity of sensor—There are 4 sensitivity levels in the sensor. You can choose your preferred sensitivity level to avoid false alarms or missed alarms; 2.Channel Setting--You can set different channels that correspond to different indicator lights in the receiver; 3.
2. Getting Started The basic steps for installing and setting up your driveway alarm are as follows: 2.1 Connect with power 2.2 Setting the Sensitivity&Channel of sensor 2.3 Pairing 2.4 Charging the sensor 2.5 Install the sensor(test before installing) 2.6 Setting the receiver 2.1 Connect with power Sensor: The sensor’s default setting has finished the power connected. You will be able to easily connect or disconnect the power line inside the sensor. The sensor also has an ON/OFF button.
2.2 Setting the Sensitivity& Channel of sensor After you have connected to power, you will need to set the sensitivity& channel of the sensor. The sensor will arrive per-configured to a default setting if you buy the set which includes the sensor and the receiver together. You will only need to set the Sensitivity & Channel of the sensor if you want to change to a different setting, or if you only purchased the sensor without the receiver to expand it.
2.3 Pairing After turning on the sensor and configuring the sensitivity settings, press & hold the “PAIRED” button to enter PAIR mode and wave your hand slowly in front of the sensor. At this time, the sensor will detect the movement of your hands and display a red light. The receiver will also ring, indicating a successful pairing set up. The sensor will arrive per-configured to a default pairing setting if you buy the set of the sensor and receiver together.
2.5 Install the sensor(test before installing) After the sensor is fully charged, you can install the sensor in an outdoor setting where you want to detect motion. You can do this with the included screwdriver. For better security, you can adjust the angle of the sensor eye by moving the ball-joint after you’ve completed installation. Install it with the included screws and screwdriver. Ball joint. Adjust the angle of sensor. 2.
Press MENU button fourth time, indicator 1 flash, press UP/DOWN to set the hour of alarm; Press MENU button fifth ime, indicator 2 flash, press UP/DOWN te set the minute of alarm; Press MENU button sixth time, quit time&alarm setting. Note: when you choose OFF at third time, you will quit setting when press MENU button fourth time, it means no alarm you need.
2.7 Usage Scenarios 1.After you have received your package, open it, and install the sensor in an outside setting where you want to detect motion. (The sensor will be in its default setting when it leaves the factory.) 2. Once the sensor detects animals, people, or cars), the sensors eye will flash red and send a signal to the receiver. 3.
vanned Settings 3.1 Volume Setting The melody volume is adjustable. In the standby mode (indicated by a screen display of the current the UP/DOWN button to adjust the volume. There are 8 volume levels available. In standby status, press UP/DOWN button to adjust volume. 3.2 Mute Mode Press&Hold the “MUTE” button for 3 seconds to activate the device’s mute mode.
3.3 Melodies Setting This driveway alarm system can be expanded interconnected sensors. You can set a different melody for each of these sensors to help you judge which sensor has recently detected movement. In total, there are 36 melodies available. In standby mode, press the PARTED button, and the screen will show 4 characters. The first two characters (C1, C2, C3, etc.) stand for the channel number. There are 8 channels (C1-C8). The remaining 2 characters indicate the melody number (01-36).
3.4 Time& Alarm Setting The receiver also includes both clock and alarm functions. LED Indicator 1(Hour number} LED Indicator 2 (Minute number) LED Indicator 3 (Time mode) LED Indicator 4 (Alarm function on) Time Mode, LED Indicator 3 ON; Have alarm,LED Indicator 4 ON; no alarm, LED Indicator 4 OFF.
3.5 Pairing After turning on the sensor and configuring the sensitivity settings, press & hold the “PAIRED” button to enter PART mode and wave your hand slowly in front of the sensor. At this time, the sensor will detect the movement of your hands and display a red light. The receiver will also ring, indicating a successful pairing set up. At the time the sensor leaves the factory, it will already be configured with its default settings to enable you to use it immediately.
3.6 Power& Charge 3.6.1 Charge Sensor The sensor is equipped with a 1800mA rechargeable battery and solar panel, it can continue to work up to 24 months after it has been fully charged. However, sensors are only charged to about 20% power when they leave our factory, so you will need to charge it before installing. when charging Battery connected Please charge it before installing. We suggest that you turn off the sensor while it charges by pressing and holding the POWER button. 3.6.
4.Additional Notes 1. The sensor has 4 different sensitivity settings (Hi,Mid 1,Mid 2,Low). If you find that your sensor often has false alarms due to high sensitivity, you can lower the sensitivity for better results.Also, if you find that the sensor often misses the alarms, you can increase the sensitivity to a higher setting. 2. This sensor features our latest technology, which has been improved to avoid false alarms, like falling leaves or mosquitoes.
5.Troubleshooting Most issues that arise can easily be resolved by changing the settings on your products. Please read this user manual carefully before you use this machine. Use the table below to find your exact issue and the possible solutions for it.
6.Adding Additional Sensors If you want to build a larger detection range, you can expand your alarm system by adding more sensors. This alarm system can expand sensors all on the same receiver. How to add: 1.Buy an additional sensor in our store, and add it to your previously purchased alarm system; 2.Configure the new sensor using the steps above. Connect the new sensor to battery , configure the sensitivity level, and set the channel umber.
7.Questions & Answers Here we have sorted out some of the common problems encountered by our customers. We have provided detailed answers for your reference that can hopefully help you find all the solutions to your issues. Question 1: My alarm has not worked in several months, what should Ido? Answer 1: For this kind of problem, we suggest the following: 1: Check if the sensor is turned off. The sensor can work for up to 24 months after it has been fully charged.
Question 3: Sometimes the alarm works well and sometimes it doesn’t. Why? Answer 3: This issue is often caused by improper sensitivity settings. Please disassemble the sensor and adjust the sensitivity for improved results. If you have any additional concerns, please feel free to contact us via our customer service at: Email: Facebook : @Unofficial We will do our best to answer within 12 business hours.