C-5000/RT-5000
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Chelton Avionics Inc., dba Wulfsberg Electronics Division, a Cobham Avionics & Surveillance Group Company, hereafter referred to as Cobham Avionics, is located in Prescott, Arizona. Wulfsberg Electronics designs and manufactures the Wulfsberg Electronics C-5000 suite of products, including the FLEXCOMM, FLEXCOMM I and FLEXOMM II.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Record of Revisions Rev No. Rev Date A 10/04/2001 B 07/24/2008 C 11/19/2008 D 06/19/2009 E 07/29/2010 Date Inserted Publication No. 150-041102 Rev E By Rev No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Record of Revisions Rev No. Rev Date Date Inserted Publication No. 150-041102 Rev E By Rev No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual TABLE OF CONTENTS Section Page 1. Applicability .......................................................................................................................................... 9 2. Glossary ...............................................................................................................................................9 3. Introduction ...............................................................................................
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual TABLE OF CONTENTS (CONT’D) Section Page 6. CPS Software Description and Programming .................................................................................... 32 A. Before you Begin.......................................................................................................................... 32 B. CPS Code PMA File Details ........................................................................................................ 32 7.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual TABLE OF CONTENTS (CONT’D) Section Page 10. Trunking.............................................................................................................................................. 66 A. Trunking Configuration................................................................................................................. 66 B. Trunking System ...................................................................................................
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual This page intentionally left blank. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual 1. Applicability This manual describes how to configure and use Cobham C-5000 Communication Management Controllers with part numbers in the 31300-1X02-XXXX series (where X can be any digit), and the civil support software configuration. Although this manual is largely applicable to previous software versions, some recently added features may not be available, and minor operational changes in previously available features may exist. 2.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Flexcomm I – First generation of Flexcomm control heads and transceivers. This includes the C-1000 control head and RT-30, RT-138(F), RT-450, RT-406F transceivers. Flexcomm II – Second generation of Flexcomm control heads and transceivers. This includes the C5000 control head and RT-5000 multi-band transceiver. FM – Acronym for “Frequency Modulation”.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual OTAR – Acronym for “Over The Air Re-key”. Method by which the Encryption Key is transmitted over the radio channel, hence “over the air”. P-25 – Digital Modulation Standard. Page – The contents of the display, sometimes called a screen or view. PL – Acronym for “Private Line”, also known as CTCSS or sub-audible tone. Preset Channel – A channel that has been programmed into the memory of a control head or transceiver. Private – Another name for encryption.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual 3. Introduction The Cobham C-5000 Communication Management Controller (CMC) is a microprocessor-based control head device that controls one or two Cobham transceivers. The C-5000 supports the full line of Cobham FLITECOMM, FLEXCOMM I, and FLEXCOMM II transceivers. This manual is intended to quickly instruct the user on the basic operations of the C-5000 and also outline the advanced operations that set the C5000 apart from any other communication device.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual 3. FLITECOMM This product line is no longer manufactured, but remains in wide use. It consisted of the RT-7200, RT- 9600, and RT-9600F transceivers. They were available with a two-channel, crystal-controlled, Guard Receiver that could be user-specified for any Guard frequency between 138.000 and 173.9950 MHz (RT-7200) or between 150.000 and 173.9975 MHz (RT-9600/9600F). They were equipped with CTCSS tones on both the Main and Guard Receivers. C.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (5) Using the CPS software, read the codeplug out of the ITM. Save this first as a back-up in case you need to return to the factory setting. (6) Modify system settings for your application. Program the personalities and assign Zone/Channels. It is important to use good channel identifiers so CPS operators can efficiently determine the purpose of the channel.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual 4. Configuration Availability RT-5000 P/N options (with embedded XTS-3000 ITM modules) PN 400-015525-XXXX -0611 Internal 138-174 -02 Transceiver 403-470 M M Module 450-520 P P P P (MHz) 764-806 T T T T Y Y Y Y S S S S X DES.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual RT-5000 P/N options (with embedded XTS-3000 ITM modules) cont’d PN 400-015525-XXXX -2811 -2911 -3011 -3111 -3211 -02 -12 E E E E Internal 138-174 Transceiver 403-470 M M M M Module 450-520 P P P (MHz) 764-806 T T Y Y A.E.S. Encryption E -13 -14 Y X D.E.S. / XL / OFB Encryption T S D.V.I.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual RT-5000 P/N options (with embedded XTS-5000 ITM modules) (cont’d) PN 400-015525-XXXX -6111 -8211 -9999 E ITM Frequency 380-470 450-520 -10 -10 806-870 M P -27 T -28 A.E.S. Encryption X X X X D.E.S./XL/OFB Encryption X X X X D.V.P./XL Encryption Y S D.V.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual 5. Configuring the C-5000 A. Configuring the C-5000 Although Cobham highly recommends using the PC based Remote Programmer software to specify the C-5000’s configuration, it can be specified from the front panel. The process is as follows. (1) Ensure you are on the HOME PAGE. (2) Press the PROG button. You will be prompted to enter a password, as follows. E N T E R # = . . P A S S WO R D . .
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (8) Use the cursor/value knobs to input the last four digits of your C-5000’s part number. Press the MODE button to display the next menu page. S E T U P : 2 = N E X T E N T E R = S E T U P 3 = B A C K R A D I O # 1 (9) You can press the ENTER button to configure radio 1. Refer to the sections on configuring RT-5000 and non-RT-5000 radios for details on these sub-menu pages. Press the MODE button to display the next menu page.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual S Y S T E M S E T U P H O M E = E X I T M O D E 2 = R E V I E W (14) Press the HOME button to exit system configuration, or the MODE button to review current settings. B. Configuring the C-5000 to Control an RT-5000 This section covers the radio setup sub-menu pages. Refer to the section on configuring the C-5000 for details on how to reach these menu pages.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual S Y S # 1 : 2 = N E X T R A D I O M O D E = 3 = B A C K 1 (4) This page will only display if the RT-5000 part number entered indicates an ITM is present. Use the cursor/value knobs to select a value of 1 or 2. Mode 1 indicates that the ITM should act as part of the main transceiver, i.e. the two transceivers appear to be a single unit. Mode 2 indicates that the ITM should not act as part of the main, i.e. it should behave as a Guard receiver.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual S E T U P R A D I O H O M E = E X I T # 1 2 = R E V I E W (8) Press the HOME button to exit the radio setup menu pages, or press the MODE button to review the current settings. C. Configuring the C-5000 to Control A Non RT-5000 This section covers the radio setup sub-menu pages. Refer to the section on configuring the C-5000 for details on how to reach these menu pages.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual S Y S # 2 : 2 = N E X T R T - 1 3 8 F 3 = B A C K P R E S E N T - N O (5) Use the cursor/value knobs to tell the C-5000 if an RT-138F is present. Press the MODE button to display the next menu page. S Y S # 2 : 2 = N E X T R T - 4 5 0 3 = B A C K P R E S E N T - N O (6) Use the cursor/value knobs to tell the C-5000 if an RT-450 is present. Press the MODE button to display the next menu page.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual S Y S # 2 : 2 = N E X T G U A R D # 1 3 = B A C K P R E S E N T - Y E S (11) Use the cursor/value knobs to tell the C-5000 if a Guard is present. Press the MODE button to display the next menu page. S Y S # 2 : 2 = N E X T E N T E R = S E T U P 3 = B A C K G U A R D # 1 (12) This page only appears if a guard is present. Press the ENTER button to configure the first Guard channel.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (16) Use the cursor/value knobs to tell the C-5000 if an internal DCS tone board is present. (Represented by a “3” in the C-5000 part number, i.e. 31300-XXXX-X333). Press the MODE button to display the next menu page. S E T U P R A D I O H O M E = E X I T # 2 2 = R E V I E W (17) Press the HOME button to exit the radio setup menu pages, or press the MODE button to review the current settings. D.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual E. Setting Miscellaneous Configuration Options This section covers the miscellaneous setup sub-menu pages. Refer to the section on configuring the C-5000 for details on how to reach these menu pages. We pick up at the following display page: S E T U P : 2 = N E X T E N T E R = S E T U P 3 = B A C K M I S C . (1) Press the ENTER button to begin configuring miscellaneous options.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual S E T U P : 2 = N E X T C - 5 0 0 0 3 = B A C K D E E M P H - N O (6) This page only appears if system encryption is available. Use the cursor/value knobs to tell the C-5000 if it should use de-emphasis. Press the MODE button to display the next menu page. M I S C H O M E = E X I T S E T U P 2 = R E V I E W (7) Press the HOME button to exit the miscellaneous configuration menu pages, or the MODE button to review current settings. F.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual The 3-digit hexadecimal number to the right of the display on the lower line will increment from 000 to 2FF while the download is in progress. When the download is complete, the C-5000 will automatically restart. H. Uploading a Configuration from the C-5000 into RpWin The C-5000’s current configuration can be uploaded into the RpWin software as follows: (1) From the HOME page, press the PROG button, and enter the appropriate password.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual I. Entering CPS Load Mode Digital RT-5000’s must have the ITM(s) loaded with Motorola CPS before being able to TX/RX on digital channels. Enter into CPS Load Mode by doing the following: (1) From the HOME page, press the PROG button, and enter the appropriate password.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual P R O G : 2 = N E X T < E N T E R > = 3 = B A C K K V L L O A D (3) Press ENTER button to enter the KVL LOAD screen: S T A R T K V L R A D I O = 1 L O A D I T M = V H F 1 3 8 (4) Use the cursor to select either Radio 1 or 2 (if available), and between VHF or UHF ITM depending on RT-5000 model number: S T A R T K V L L O A D R A D I O = 1 I T M = U H F 8 0 0 (5) Press START to open the KVL data lines and load the encryption keys into the RT-
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual P R O G : 2 = N E X T < E N T E R > = K E Y 3 = B A C K E R A S E (3) Press ENTER button to enter the KEY ERASE screen: S T A R T K E Y R A D I O = 1 E R A S E I T M = V H F 1 3 8 (4) Use the cursor to select either Radio 1 or 2 (if available), and between VHF or UHF ITM depending on RT-5000 model number: S T A R T K E Y R A D I O = 1 E R A S E I T M = U H F 8 0 0 (5) Press START to erase the encryption keys.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual resident archive stored in the RT-5000 ITM from the factory. Add more channels once the first one is proven. Alternatively, the ITM comes from the factory with all the necessary information loaded in it for basic operation. The user only needs to load system information such as USER ID’s, personalities, and zone/channel allocation. Once an archive for an ITM is established, it can be cloned to other ITM’s in other RT-5000’s of the same flavor.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual A. General – This menu contains the model number, serial number, FLASHcode version, and an assignable codeplug alias. B. Tracking – Allows you to view information regarding the last programmed date, time, and source of CPS and FLASHport. C. Versioning – Allows you to view the latest software versions applied to the codeplug and ITM. D. Feature Set – Allows you to view the feature set that is installed in the ITM. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual 8. Radio Configuration – Menu contains elements that affect the overall operation of the radio. A. Radio Wide – These menus allow you to modify settings that affect the overall operation of the radio. Note: These are necessary to allow integration of the ITM with the C-5000/RT-5000 system. (1) General – This menu contains general elements of the ITM. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Note: DO NOT change any of these settings from the defaults. (2) Emergency –This menu is for setting up the emergency features of the ITM. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (3) TPS – This menu allows you to modify Tactical Public Safety (TPS) elements. (4) Alert Tones – This menu allows you to modify alert tone elements radio wide. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (5) Time-Out Timers – This menu allows you to modify port timing elements. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (6) Home Mode – This menu allows you to change Home Mode elements radio wide. Note: DO NOT enable this option. (7) Advanced II – This menu allows you to change advanced elements radio wide. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (8) RX Audio Control – This menu allows you to change received audio control elements radio wide. (9) Surveillance Mode – This menu allows you to change Surveillance Mode elements. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (10) Data – This menu allows you to modify the Radio Wide Data used for the Trunking Systems. (11) TX Audio Control Per Mode – This menu allows you to chance transmit audio control elements radio wide. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (12) Digital Audio Options – This menu allows you to enable the feedback indication of the received audio quality. (13) Advanced - These are necessary to allow integration of the ITM with the RT-5000 system. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual B. NAT List – This allows you to configure the Network Address Translation. C. Controls – This contains the Display and Menu options. Settings should be as follows: (1) Buttons – These are set at the factory level and should remain as follows: Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual . (2) Hand Held Control Head - ALL entries should remain set to UNPROGRAMMED. (3) Switches – Settings should be as follows: Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual D. Display and Menu (1) General – This menu allows you to modify basic elements of the radio’s display. Here you can also change the zone and channel text size. (2) Menu Items - This menu sets up some very critical items in order for the RT-5000 to communicate with the ITM. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual ****VERY IMPORTANT****: THESE SETTINGS MUST BE EXACTLY AS SHOWN !!!!! For ITM’s with encryption set up as follows: Conv Item Trunk Item ZONE ZONE CHAN CHAN MUTE MUTE KEY ERAS REKY DIR DIR DIR For ITM’s without encryption set up as follows: Conv Item Trunk Item ZONE ZONE CHAN CHAN MUTE MUTE DIR DIR DIR DIR DIR (3) Radio Lock – This menu allows you to modify the radio’s security elements. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (4) Advanced – This menu allows you to modify the radio’s display elements. E. Phone – Contains menus to configure the system to use DTMF codes. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (1) Phone Configuration – This menu allows you to modify the radio’s Phone configuration settings applied to Conventional and Trunking personalities. (2) DTMF Codes – This menu allows you to configure the codes used by the radio when utilizing a Phone System. (3) Phone Number – This menu allows you to select the DTMF number for the Phone Number used by the radio. F.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (c) MDC OTAR –This page controls all radio settings specifically applicable to MDC (Analog) OTAR operations. (d) Multikey Options – This screen controls the number of User Selectable Encryption Keys, the CKR (Common Key Reference) and Key Names. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (e) Multikey –This page controls additional items necessary for the OTAR and secure functions to operate properly. These are necessary to allow integration of the ITM module with the RT-5000 Flexcomm system. DO NOT make changes to these unless instructed. (f) Advanced – This menu allows you to modify the Advanced options that apply to the Secure Configuration. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (2) Secure Multikey List – This allows you to modify multiply encryption keys for Secure communication. (3) Secure KMF Profile – This menu allows you to modify the Secure Key Management’s elements. (a) ASTRO OTAR Information – This menu allows you to modify ASTRO and OTAR elements. (b) Data Transport – This menu allows you to modify elements used in sending Key Management Messages. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (c) Secure Hardware Encryption Key Reference List – Allows you to modify the set of Common Key References (CKR) the Key Management Facility (KMF) can attain. 9. Conventional - All the aspects of any given channel are assigned to a personality numbered 1 through 255. These menus allow the user to modify the settings for the Conventional Personalities. A. Conventional Configuration – These menus are used to configure the conventional personalities.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual B. MPL – Allows you to configure the Multiple Private Line setting. (1) MPL Configuration – This menu allows you to modify the General MPL configuration settings. (2) MPL List – This menu allows you to select a MPL from the current available MPL entries. Note: DO NOT enable this option. C. Conventional Personality – Contains the assigned personalities and the configurations for each.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual This box is normally DISABLED. The user may also designate the RX Voice/Signal Type as either ASTRO, Non-ASTRO, or Mixed Mode which will allow you to RX in both ASTRO and Non-ASTRO mode. Utilize the Squelch (Fine Tune) to adjust the squelch level. (2) TX Options – This menu allows you to modify the Conventional Personality’s TX settings.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (3) Signaling - This menu allows you to modify the Conventional Personality’s Signaling System. The Signaling Type may be None, MDC, Quick-Call II, or DTMF. (4) MDC – This menu controls Selective Calling and Paging features of the radio, along with control of the transmit function when other signals are present on the frequency. Please note these options are only available if MDC is selected as the Signaling Type in the Signaling menu.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (5) Secure – This menu allow you to modify the Conventional Personality’s Secure options. The user may select Clear or Secure in the Secure/Clear Strapping option and may select either DES-XL, OTAR, or ASTRO OTAR. (6) Secure II – This menu allows you to modify the Conventional Personality’s secure TX and encoded RX operations. The user may select a key in the Voice Key Selection as well as select Strapped in the Key Strapping option.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (11) Advanced – This menu allows you to modify complex features of the Conventional Personality. These options are left DISABLED. (12) ASTRO – This menu allows you to modify the Conventional Personality’s ASTRO parameters. (13) ASTRO Call – This menu allows you to modify the Conventional Personality’s ASTRO System functions. (14) ASTRO Talkgroup Options – This menu allows you to modify the Conventional Personality’s ASTRO System Talkgroup List functions.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual E. Status Alias List – This is used to configure various short status messages to send via the radio. This feature is currently not used in the FLEXCOMM System. F. MDC – This is used to configure the MDC operations of the radio. (1) MDC Call List - This allows you to modify MDC call list menus. (2) MDC Repeater ID List – This allows you to modify IDs for repeaters. (3) MDC System – This menu controls the setup for MDC (Analog) operations.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (c) Emergency Revert – Allows the user to select a preset used to TX data in Emergency Mode for the Conventional Personality. This menu is only available when Emergency Enable is ENABLED in the Emergency Menu. (d) Emergency – Allows the user to enable the Emergency Enable for the Conventional Personality. Normally set to DISABLED. (e) Repeater Access – Allows the user to enable Repeater function for the Conventional Personality.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual G. Quick-Call II – This is used to configure the Quick-Call II call alert and selective call for each personality. (1) Quick-Call II Call List – This allows you to select which Quick-Call II Call List to be used for the Conventional Personalities. (2) Quick-Call II System – These menus allow you to modify the settings for the Quick-Call II System. (a) General – This menu allows you to modify the General settings of the Quick-Call II System.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (b) Advanced - This menu allows you to modify the Advanced settings of the Quick-Call II System. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual H. DTMF – This is used to configure the DTMF (Dual Tone Multiple Frequency) options. (1) DTMF Call List – This allows you to select which DTMF Call List to be used for the Conventional personalities. (2) DTMF System – These menus allow you to modify the settings for the DTMF System. (a) General – This menu allows you to modify the General settings of the DTMF System. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (b) Advanced – This menu allows you to modify the Advanced settings of the DTMF System. I. Singletone – This is used to configure the Singletone frequency options. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (1) Singletone Frequency List – This allows you to select which Singletone Frequency is to be used for the Conventional Personality repeater access. This is only available when the Repeater Access Type is set to Singletone in the Conventional Personalities. (2) Singletone System – These menus allow you to modify the settings for the Singletone System. PTT Sidetone: RAB Sidetone: Tone Pretime (ms): Tone Duration (ms): ENABLED ENABLED 250 500 J.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (f) Soft ID – This menu allows you to modify the Soft ID feature used whenever the PTT button is pressed. Soft ID Feature: ENABLED (2) ASTRO System – These menus allow the user to modify the settings for ASTRO Digital operations. All of the settings should remain as depicted EXCEPT the Individual ID. This is the ASTRO ID assigned to the radio by serial number when it is first brought on line in the radio network. It must be unique to the radio.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Limited Patience Time (sec): Polite Retries: Impolite Retries: TX Multiplier: Global TX Multiplier: Silent Override w/Mon: 0 5 15 0 DISABLED DISABLED (d) Advanced – This menu allows you to modify the Advanced settings for the ASTRO System. (e) ARS – This menu allows you to modify the ARS (Automatic Registration Service) settings.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual A. Trunking Configuration – This is used to configure the trunking system and all trunking personalities. (1) General – This menu allows you to modify the General options that apply to Trunking Personalities. (2) Common Air Interference – This menu allows you to change elements of the data sent utilizing the CAI protocol. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (3) SMARTZone – This menu allows you to modify elements of the SMARTZone functions that can be utilized for all Trunking Personalities. Note: Older Archive CPS files contained “Display Site Trunking” ENABLED. However this must be DISABLED in order to function properly with customer trunking systems. (4) RSSI Thersholds – This menu allows you to modify elements of the Received Signal Strength Indication (RSSI) utilized for all Trunking Personalities.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (5) Filter Constants – This menu allows you to modify Filter Constants used in conjunction with the RSSI Thresholds that can be applied to all Trunking Personalities. (6) Phone – This menu allows you to modify the Trunking Personality’s Phone Interconnect for land-to-portable calls. B. Trunking System – This is used to set-up the advanced options of the trunking system.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (a) General – This menu allows you to modify the General settings of the Trunking System. (b) Type II – This menu allows you to modify the Type II Trunking Setting when Type II is selected in the General menu. (c) DTMF- This menu allows you to modify the DTMF settings for the Trunking System. (d) Aliasing – This menu allows you to modify the Aliasing setting for the Trunking System.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (i) ASTRO 25 Channel ID - This menu allows you to view the Channel ID settings for the Trunking System. (j) 700_800 ASTRO Control Channels – This menu allows you to modify the Control Channel settings for the ASTRO 25 mode. (k) Data – This menu allows you to modify the Data Settings for the Trunking System. (l) ASTRO 25 Omnilink – This menu allows you to modify the Omnilink settings for ASTRO 25 mode.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (o) Dynamic Regrouping – This menu allows you to modify the Dynamic Regrouping settings. Enable Dynamic Regrouping: DISABLED (p) ASTRO 25 – This menu allows you to modify the ASTRO 25 settings for the Trunking System. (q) Digital – This menu allows you to modify the Digital settings used for digital communications. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (r) Multikey- This menu allows you to assign Multikey fuctions. C. Trunking Personality – This is used to set-up individual trunking personalities, as well as select Type II or ASTRO 25 Trunking. (1) General – This menu allows you to modify the General settings of the Trunking Personality. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (2) Emergency - This menu allows you to modify the Emergency settings of the Trunking Personality. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (3) Secure – This menu allows you to modify the Secure settings of the Trunking personality. (4) Scan – This menu allows you to modify the Scan features of the Trunking Personality. Please note that Scan is not currently available in the FLEXCOMM II System. Scan List Selection: None (5) Phone – This menu allows you to modify the Phone settings for the Trunking Personality.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (8) Talkgroup – This menu allows you to select the Talkgroup for the Trunking Personality. (9) Call/Page – This menu allows you to select the Call and Page Operation for the Trunking Personality. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual (10) Preferred Sites – This menu allows you to select the Preferred Sites for the Trunking Personality. (11) Emergency Revert – This menu allows you to modify and select the Emergency Revert function for the Trunking Personality. D. Trunking Call List – This is used to create trunking call lists. E. Type II Trunking Call List – This is used as an advanced feature of the trunking system which allows talkgroups to be set-up as trunking channels. 11.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual 12. Zone Channel Assignment – These menus are used to assign any of the possible 255 Personalities to a specific zone and channel, as well as enter the TX and RX frequencies, and assign the Personality Type as either Conventional (Cnv) or Trunking (Trk). Please follow the CPS programming notes outlined in Section 3 of this manual. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual This page intentionally left blank. Appendix A – CTCSS (PL) Tone Codes Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual C-5000 TONE CODE TONE FREQ (HZ) EIA TONE CODE C-5000 TONE CODE TONE FREQ (HZ) EIA TONE CODE 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 N/A N/A 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 N/A N/A 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 N/A N/A 156.7 162.2 167.9 173.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual This page intentionally left blank. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Appendix B – Mode 2 Operation Overview The C-5000 has the capability to control the RT-5000 in such a way that the user can monitor both the main and the Guard (ITM) channel at the same time. This mode of operation is more difficult to use than MODE 1. The Home Page The only visible difference in the HOME PAGE from Mode 1 operation is in the Main/Guard status fields.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Setting the Active Transceiver You can toggle the active transceiver for a radio between Main and Guard by pressing the soft keys. The UPPER SOFT KEY toggles the active transceiver for radio 1. The LOWER SOFT KEY toggles the active transceiver for radio 2. The following sequence of illustrations demonstrates this process for radio 1. The Main transceiver is currently active. 1 1 2 2 1 2 3 . .
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Appendix C – Single Microphone Operation Overview Starting with software modification 11 (SWID 11), the C-5000 has the ability to control both radios with a single microphone/headset. This feature, hereafter called single-mic mode, is useful for installations where audio panel space is limited, or it is otherwise impractical to dedicate two ports to the C-5000.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Setting the Active RT You can change the active RT by pressing the soft keys. If radio 1 does not already contain the active RT, pressing the UPPER SOFT key will make radio 1’s active transceiver the active RT. If radio 1 already contains the active RT, pressing the UPPER SOFT key toggles the active RT between radio 1’s Main and Guard. The LOWER SOFT key performs the same operations for radio 2.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Muting Inactive Receivers The C-5000 can be configured such that the DIM key invokes the MUTE function rather than the DIM function. When MUTE is active, the audio from all non-active transceivers will be muted. Muted transceivers are indicated by an ‘M’ character in their status fields. See depiction below. . 1 5 M M . . .
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual This page intentionally left blank. Publication No.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Appendix D – Equivalent Part Numbers Because RT-5000’s and C-5000’s are maintained as separate products, there can be circumstances when a new flavor (part number) of RT-5000 is released, but the C-5000 is not yet aware of its existence. This problem manifests itself as rejected part numbers in the C-5000 configuration pages for RT-5000 radios.
FLEXCOMM II C-5000 (P-25 Capable) Operator’s Manual Appendix D – Equivalent Part Numbers (cont’d) -5411 -5511 -5611 -5711 -5811 -5911 -6011 -6111 Publication No.