UA-220 User Manual Manufacture: Woxu Wireless Co,Ltd.
Copyright Notice Copyright © 2020 Woxu Wireless Co., Ltd. and its license all rights reserved, all rights reserved. Without prior written permission of the company, any unit or individual shall not be allowed to extract and copy all or part of the contents of this book, and shall not in any form of communication. This manual is likely to change as a result of product version upgrade or other reasons. Our company reserves the right to modify the contents of this manual without any notice or prompt.
Preface Location Anchor is a kind of anchor based on UWB manufactured by Woxu Wireless Co.,Ltd., which is for human and goods indoor location with high precision. This document introduces the method to use and configure the anchor. Contents:Reader, Appointment , Technical support Reader This manual is mainly applicable to the following engineers: 0. Students and teachers and developers 0.
IMPORTANT NOTE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CONTENT Preface.................................................................................................................................................... 3 CONTENT ............................................................................................................................................. 5 1 Configuration ...................................................................................................................................... 6 1.1 WEB .................................
1 Configuration 1.1 WEB Web information in default is as below: Device information list IP address User name Key Device information 192.168.1.9 woxuwireless woxuwireless note Changeable NOT Changeable Changeable Attention 1. If you change the key, please save the key, if you really forgot it, please contact us or your seller. Log in Web as below step (1) Connect device and PC Connect the PC to the device’s network over cable.
(3) Start up the browser and input log-in information, Start up the browser in PC, input the device’s IP address in address bar, (default IP is 192.168.1.9),you can log in the Web pages, Input user name “woxuwireless”,Key“woxuwireless”, click . 7 Woxu Wireless Co.,Ltd. www.woxuwireless.
Login display page 1.2 About page Function selection Function Page list About web page, there are three regions: 1. Function selection, select the different function item, in the main function region, will display the corresponding item. 2. Function, Web pages are mainly presented and operated, such as status display, network configuration, etc. 3. Status and configuration 1.3 status In this item, includes"WLAN","Statistics""Network","Device", display different information. 1.3.
1.3.2 Statistics The wired part and the wireless part respectively count the number of packets received and sent and the number of errors. 1.3.3 Network information Display device network information 1.3.4 Device information Display hardware and software information. 9 Woxu Wireless Co.,Ltd. www.woxuwireless.
Device display Friendly name: the device name you defined, in this device, it is displayed as “UWB Gateway”. Hardware version:current hardware version Software version: current running version Release time: the version released time Serial Number: current device serial number Wired MAC : current device wired physical address Wireless MAC:current device wireless address System time:current system time Uptime:current system running time 1.4 Set Wi-Fi network 1.4.
record. 2.Select wireless network scan.
1.4.2 Wi-Fi scan You can see that the Peer MAC address has been entered in the MAC of the destination AP, if the authentication & encryption mode does not enter the authentication & encryption mode of the destination AP, manually modify, click the application, and the binding can be generated. The device will scan the AP or router that can be searched to display its MAC address, SSID, authentication and encryption mode, signal intensity, working channel and mode.
Attention When modifying the device IP, note that the IP of PC is in the same network segment as device IP, but it cannot be the same. For example, the device IP is 192.168.1.3, and the IP of PC can be set to 192.168.1.1,192.168.1.254,192.168.1.3,Among them, 192.168.1.X represents the network segment and needs to be consistent. Modify IP address Modify the IP address IP address:it’s IP address about LAN port,default is 192.168.1.9, Subnet mask:it’s for LAN,default is 255.255.255.
Device name and updated time interval Modify device name and amend status updated time interval. Device name:the device name Status updated time interval: device status update time interval After configuration, click application, the result can be checked in the status page. Key management Amend user and password. Default user name is woxuwireless,Key is : woxuwireless. According to this page, you just need to input new key, click “application”.
Click
Restore factory configuration: click, the configuration about the device will restored as default data. 1.6.4 System log Enable system logs to display important information about the system., select to clear the log content. Enable remote system log, set server IP address and server port, can get the remote system log information. 1.6.5 System service Four parts: SNMP、NTP management、allow management HTTP port and enable TELNET 16 Woxu Wireless Co.,Ltd. www.woxuwireless.
Enable SNMP:is used to set up SNMP(simple network management protocol); NTP management: manual and NTP,to set system time; Allow management HTTP port :default allow, default port is 80; Enable TELNET: default is enable, default port is 23. 1.6.6 Reboot Click , the system will reboot. 1.7 UWB Five parts :Basic settings, Advanced, Statistics,UWB Upgrade,RF Gateway 17 Woxu Wireless Co.,Ltd. www.woxuwireless.
1.7.1 Basic settings Display current device’s UWB version about H/W and software , set its ID, others are set off from the server. It can be selected from 0 dBm, but it is not for end users, it is for technical personnel. When it sell to end users, it has been locked. 1.7.2 Advanced Used to set up sub-anchor list and team number. 18 Woxu Wireless Co.,Ltd. www.woxuwireless.
1.7.3 Statistics It is used to count the data of sending packets, sending successful data, and receiving message data. 1.7.4 Upgrade Upgrade step: (1)Open the Upgrade page, as below: 19 Woxu Wireless Co.,Ltd. www.woxuwireless.
(2) Click “select file” and import bin file, such as UA220 APP V3.0.18.bin (3) Open the management page and click restart. (4) Open UWB page, check whether it is the updated version information. If it fails, restart the device and check UWB status, if it is not successful, repeat the above steps. If it always fails, please contact us. The whole software bundle is upgraded. Common users cannot modify the software. The software can be obtained by the website www.uwbleader.com or Woxu support team.
Woxu Wireless Co.,Ltd. www.woxuwireless.