User's Manual

Contents of Air Swimmers Killer Whale Box
1 x Air Swimmers Killer Whale balloon
1 x Tail fin
1 x Tail motor unit
2 x AA batteries
3 x Elastic bands
4 x Double sided sticky pads
1 x Pod 1 x Controller
1 x Putty holder
Spare part included:
1 x Elastic band
1 x Putty
4 x Clear tape tabs
4. 5.
7.
8.
9.
11.
12. 13. 14.
10.
6.
1 x AAA battery
1. To fill the Air Swimmer with helium, lay the Air
Swimmer balloon (1) out flat on the ground and
insert the helium tank nozzle into the valve at
the back of the balloon.
2. Release the helium
slowly so that the
balloon starts to inflate
and increase it gradually
until the balloon is full
and firm.
Warning: Do not over-
inflate the balloon.
The balloon’s valve
does not require
sealing after inflation.
Warning: DO NOT OVERINFLATE THE BALLOON. Only inflate with helium. Do not use any other type of gas.
Do not use any other inflation devices such as a foot pump.
For easy-to-follow video instructions go to www.wowstuff.com/airswimmers
You can store your Air Swimmer by attaching the
hook on the end of the remote control (7) to one
of the loops on the bottom of the Air Swimmer.
Pod
The pod (11) requires 1 x AAA battery (13).
Remote Control
The remote control (7) requires 1 x AA batteries (12).
5. Fold over the fastening clips on the tail motor unit
to secure.
6. Place the tail motor
unit (8) on the back
of the Air Swimmer
balloon and attach
the three elastic
bands to the hooks
on the motor unit.
Make sure the plug
connection on the
tail motor unit faces
downwards.
plug
connector
Attaching the Pod
clips
clips
1. Attach the pod track (11), by hooking the hooks
through the holes at the front of the underside
of the Air Swimmer.
2. Make sure the hooks are hooked through as shown.
The front of the pod (the fan should always be at the
front), closest to the nose of the Air Swimmer.
1. Remove the liner of the double-sided sticky pads
(9). Attach each fin in place on the Air Swimmer
balloon (marked ‘place fin here’), as shown.
2. Place clear tape tabs (6) over the fin tabs
to secure.
Attaching the Fins
3. Loop the electric wire from the pod through the
hoops underneath the Air Swimmer balloon.
4. Plug the electric wire into the tail motor unit as shown.
Note: Ensure the electric wire has the correct orientation
to the tail motor unit, as pins on tail motor unit can
become bent and damaged.
1. Turn the power
switch to “ON”
on the pod (11),
and the red
LED will
illuminate.
Flying your Air Swimmer
Attaching the Putty Holder
1. Attach the putty holder (14) to the holes on the under side of the back of the Air Swimmer. Add small bits of
putty (10) until the Air Swimmer floats at roughly 5 feet (1.5m), neither rising or falling. If it starts to descend,
remove some of the putty.
NOTE: The putty holder may not need to be used, if the Air Swimmer floats at roughly 5 feet (1.5m)
before the putty holder is attached. This is dependant on your altitude.
3. To move the Air Swimmer up, press
up on the remote. To move the Air
Swimmer down, press down on
the remote.
1. If you fly more than one Air Swimmer in close proximity
each Air Swimmer needs to be changed to a different
channel. To do this push the switch on the handset to
either A, B or C.
Please note: You do not need to complete this
instruction unless more than one Air Swimmer are
being swam in close proximity.
5. To turn your Air Swimmer, press and hold the
button in the direction you wish to turn. This
will give you a tight turning circle, but the Air
Swimmer will move slowly. To find out different
ways of turning your Air Swimmer visit
www.wowstuff.com/airswimmers.
Please note: You cannot turn and swim your
Air Swimmer forwards at the same time.
Changing The Frequency Channel
www.wowstuff.com
• 2 x AA batteries for remote controller (Included)
For more troubleshooting please go to www.wowstuff.com/airswimmers
1. Thread one of the elastic bands (5)
through the hole situated on the top
of the Air Swimmers back (as shown).
2. Thread the elastic band through itself
to create a loop.
3. Loop a second and third elastic band through
the hole situated underneath the Air Swimmer
in the same way. (Both through the same hole,
as shown).
4. Attach the tail fin (4) to the tail motor unit (8) by slotting
the rods into the tail motor unit arms, as shown.
Assembling the Tail Motor Unit
KILLER
WHALE
AAx2
www.wowstuff.com/airswimmers
4. To get your Air Swimmer moving, you will need to move the tail up and down by pressing up, down, up,
down in a constant rhythm. Experiment with faster and slower rhythms to find the best speed.
2
1 8
9
4
6
7
5
ON
OFF