SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Random orbit sander WU651 WU651L
Component list 2 1 1 On/off witch 8 2 Soft grip handle 3 Cyclonic dust box 3 4 Latching lever 4 5 Dust extraction outlet 6 Outer base plate 5 7 Inner base plate 6 8 Motor housing 9 a: Inner spot paper* (See Fig A) 7 b: Outer ring paper* (See Fig A) 10 Dust extraction adaptor(See Fig E) * Not all the accessories illustrated or described are included in standard delivery.
General power tool safety warnings will reduce risk of electric shock. b Avoid body contact with earthed or grounded surfaces, such as Warning: Read all safety warnings and all instructions. pipes, radiators, ranges and refrigerators. There is an increased Failure to follow the warnings and instructions may result in electric risk of electric shock if your body is earthed or grounded. shock, fire and/or serious injury. c Do not expose power tools to rain or wet conditions.
at the rate for which it was designed. protection. Protective equipment such as dust mask, non-skid b Do not use the power tool if the switch does not turn it on and safety shoes, hard hat, or hearing protection used for appropriate off. Any power tool that cannot be controlled with the switch is conditions will reduce personal injuries. c Prevent unintentional starting. Ensure the switch is in the dangerous and must be repaired.
Additional safety instructions for your sander tool for operations different from those intended could result in a hazardous situation. 5. Service 1 a Have your power tool serviced by a qualified repair person using Harmful/toxic dusts will arise from sanding e.g. lead painted only identical replacement parts. This will ensure that the safety of surfaces, woods and metals. Contact with or inhalation of these the power tool is maintained. dusts can endanger the health of operator and bystanders.
cables and pipes. • Lead from lead-based paints. 10 After long working periods external metal parts and accessories • Crystalline silica from bricks and cement and other masonry could be hot. products. 11 If possible, ensure the work-piece is firmly clamped to prevent • Arsenic and chromium from chemically treated lumber. movement. Your risk from these exposures varies, depending upon how often 12 Your sander is a hand held tool, do not clamp your sander. you do this type of work.
Symbols To reduce the risk of injury, user must read instruction manual Warning Wear eye protection Wear dust mask Wear ear protection Double insulation Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.
Technical data • 8 Voltage WU651L WU651 110V-50Hz 230-240V~50Hz 280W 300W • Power input • No load speed • Base size 125mm • Orbital dia 3.0mm • Protection class • Weight 12000/min /II 1.
Noise and vibration data WU651 WU651L Vibration total values (triax vector sum) determined according to EN 60745: • A weighted sound pressure 83dB(A) • KpA: 3dB(A) Typical weighted vibration • A weighted sound power 94dB(A) Vibration emission value ah = 9.35m/s2 Uncertainty K = 1.
and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period. Help to minimize your vibration exposure risk. Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate) If the tool is to be used regularly then invest in anti vibration accessories. Avoid using tools in temperatures of 100C or less Plan your work schedule to spread any high vibration tool use across a number of days.
Operating instructions note: Before using the tool, read the instruction book carefully. INTENDED USE The machine is intended for dry sanding of wood,plastic, metal and filler material as well as painted surfaces. Machines with electronic control are also suitable for polishing. KNOW YOUR RANDOM ORBIT SANDER vibrafree™ RANDOM ORBIT Sander are uniquely designed with two counter balanced sanding pads that always move in opposite directions to each other.
Make sure the sanding paper is even with the edges and that the sanding paper is taut on the pad. Remove the abrasive paper by pinching an edge and peeling off (See Fig B) 2 CYCLONIC DUST BOX (See Fig C) A) ATTACH THE CYCLONIC DUST BOX C Your sander is equipped with a cyclonic dust box. To attach, slide D.1 the box onto the outlet piece and take care that the latching lever engages.
hose of a vacuum cleaner. First please turn on the vacuum cleaner, and then turn on the sander. If you stop sanding, first turn off the sander, then turn off your vacuum cleaner. 4 OPERATING THE SWITCH (See Fig F) To start your sander, depress the protective cover over the switch at the position marked“I”. To stop your sander, depress the F protective cover at the position marked “0”. 5 ORBITAL SANDING Guide your sander parallel to the working surface and move it in circles or in a cross pattern.
Working hints for your random orbit sander start with a low grade of grit. (e.g. 60 grit) and change to a higher, finer grade (e.g. 120 or 180 grit) for finishing. If you use a fine grade for rough surfaces it will soon clog and need changing. • It is best to make a trial run on a scrap piece of material to If your power tool becomes too hot, especially when used at low determine the optimum grades of sandpaper for a particular job.
Accessory force you apply to the tool. Excessive force will reduce the sanding efficiency and cause motor overload. Replacing the sand paper regularly will maintain optimum sanding efficiency. • Cyclonic dust box 1 • Dust extraction adaptor 1 • 60 grit velcro sanding paper 5 • 120 grit velcro sanding paper 5 • 180 grit velcro sanding paper 5 We recommend that you purchase your accessories from the same store that sold you the tool.
Maintenance Remove the plug from the socket before carrying out any adjustment, servicing or maintenance. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots.
Plug replacement (UK & Ireland only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL BROWN = LIVE As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
EC DECLARATION OF CONFORMITY We, Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX Random orbit sander Type WU651 WU651L Function Removing surface material using an abrasive medium Complies with the following directives, • EC Machinery directive 2006/42/EC • EC Low voltage directive 2006/95/EC • EC Electromagnetic compatibility directive 2004/108/EC Standards conform to EN 55014-1 EN 60745-1 EN 61000-3-3 EN 61000-3-2 EN 55014-2 EN 60745-2-4 The p
Copyright © 2011, Positec. All Rights Reserved.