0 1 2 3 4 8 9 10 11 12 13 14 15 16 17 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Rotary Hammer WU330 WU330.1 WU330.2 WU330.3 WU332 WU332.
General power tool safety warnings entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly.
Additional safety points for your rotary hammer 1 Symbols To reduce the risk of injury, user must read instruction manual Always wear a dust mask. Double insulation 2 Safety boots are recommended at all times especially when using the chisel actions. Warning 3 Proper safety gloves are also recommended. 4 The high torque machine should not be used, while standing on a Wear ear protection ladder. 5 Do not use damaged or worn Chisel bits.
Component list 9 4 5 6 7 8 9 10 11 8 7 { 2 3 On/Off Switch With Variable Speed Control Switch Lock-On Button Forward And Reverse Rotation Control Function Mode Selection Switch Auxiliary Handle Adjustable Depth Stop Replacement Drill Chuck Locking Ring (WU330.2) Tool Holder Locking Sleeve Dust Protection Cap Sds-Plus Type Chuck (WU330 WU330L WU330.1 WU332 WU332.1) Sds-Plus “Quik-Change” Chuck (WU330.2 WU330.3) 11 WU330.2 WU330.3 9 6 8 { 1 10 3 2 4 1 5 WU330 WU330.1 WU330L 4 WU332 WU332.
Technical data Noise and vibration data Type WU330 WU330.1 WU330.2 WU330.3 WU332 WU332.1 WU330L (330~359-designation of machinery, representative of Rotary Hammer drill) WU330L WU330 WU330.1 WU330.2 WU330.3 WU332 WU332.
Accessories accessories are used. And the tool is being used as intended by its design and these instructions. • • • • • • This tool may cause hand-arm vibration syndrome if its use is not adequately managed. Warning: To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job.
Operating instructions 12.2 7 1 note: Before using the tool, read the instruction book carefully. 2 Intended Use The machine is intended for hammer drilling in concrete, brick and stone as well as for light chiseling work. It is also suitable for drilling without impact in wood, metal, ceramic and plastic. 1 12.1 WU330.2 WU330.3 A1 CHANGING THE DRILL CHUCK (See fig. A) (WU330.
locking by pulling on the drill chuck. • Removing the drill chuck To remove the drill chuck (13), pull the locking sleeve (8) to the rear, hold in this position and remove the drill chuck from the tool holder. 3 INSERTING AND REMOVING DRILL BIT IN SDS Take care that the dust protection cap (9) is not damaged when changing tools. • Inserting Clean and lightly oil the bit before inserting. Insert the dust-free bit into the bit holder with a twisting motion until it latches. The bit locks itself.
B C1 5 MOUNTING OF BIT IN KEYLESS CHUCK (WU330.3) (See Fig.C2) Grip rear collar of keyless chuck and rotate front collar until chuck is open sufficient for tool to be inserted. Insert the tool into the chuck. Grip rear collar and manually rotate front collar until tight. The locking mechanism is automatically released when the front collar is rotate in the opposite direction in order to remove the tool. (See Fig. C2) 6 ON/OFF SWITCH WITH VARIABLE SPEED CONTROL WU330.
D E warning: Never change the direction of rotation while the tool is rotating, wait until it has stopped. 10 ADJUSTABLE DEPTH STOP Fit the drill bit into the chuck. Loosen the depth stop by rotating the handle anti-clockwise. Slide the depth stop until the distance between the depth stop end and the drill bit end is equal to the depth of hole/screw you wish to make. Then clamp the depth stop by rotating the handle clockwise. 15 F 11 FUNCTION MODE SELECTION (See fig.
manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. warning! The operating mode selector switch may be actuated only at a standstill. warning! Prolonged use will cause the aluminum housing to become hot, do not touch. Environmental protection Working hints for your drill (hammer) Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice.
Plug replacement (UK & Ireland only) If you need to replace the fitted plug then follow the instructions below. IMPORTANT The wires in the mains lead are colored in accordance with the following code: BLUE =NEUTRAL BROWN = LIVE As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored blue must be connected to the terminal which is marked with N.
Ec declaration of conformity We, Positec Power Tools (Europe) Ltd, PO Box 152, Leeds, LS10 9DS, UK Declare that the product, Description WORX Rotary Hammer Type WU330 WU330.1 WU330.2 WU330.3 WU332 WU332.
2PDH03QPK11000A2 Copyright © 2012, Positec. All Rights Reserved.