COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 69 of 103 Exhibit 8: User’s Manual A copy of the user’s manual is enclosed below. The compliance statement for the 900 µHopper is located on page 15 of the manual. WWC MICRO HOPPER DATA RADIO USER’S GUIDE Corporate - 2441 South 385 West, West Valley City, UT 84120 • Tel. 801-575-6600 • Fax 801-575-6621 rd Engineering - 6750 West 93 Street, Overland Park, KS 66212 • Tel.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 70 of 103 TABLE OF CONTENTS Quick Start Guide…………………………………………………………………………………3-5 Contents of Developer Kit…………………………………………………………………….….3 Setting up the Radios………………………………………………………………………………3 Installing the Software…………………………………………………………………………….4 General Information………………………………………………………………………………..6 Configuring the Data Radio………………………………………………………………………7 Basic Commands………………………………………………………………………………….
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 71 of 103 Quick Start Guide Contents The World Wireless Communications Micro Hopper Developer Kit contains the following items: • User’s Guide with technical diagrams • Micro HopperRadios with RS-232 CIM Boards • 900 Megahertz Antennas • 9-volt, 0.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 72 of 103 Installing the Software You are now ready to install the software. 1. 2. 3. 4. 5. Turn on your computer and start Windows. Insert the first Install disk in your disk drive. Click the Windows “Start” button, point to “Run”. In the “Open” box type “a:setup” and press Return. Follow the instructions on your screen, inserting the remaining disk(s) when prompted.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 73 of 103 3. Click on the “Terminal” button to open the terminal test window. You should see the screen as shown below. 4. Go to the Settings… drop down box and select a baud rate of 19,200. Also select the New Line check box, this will cause the cursor to advance to a new line each time a carriage return is received. 5. Setup the second radio in the same manner. 6.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 74 of 103 WWC Micro Hopper Data Radio General Information The Data Radio is a frequency-hopping data transceiver operating in the 902-928 MHz ISM band. The transceiver is designed to operate under Part 15 of the FCC rules and regulations and is designed as an OEM module for professional integration into other products or field devices.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 75 of 103 v Programming and Configuring Selections Commands are accepted by the radio when it is in “configure” mode. On the figure of the main menu shown above, “Configure” toggles with “Disconnect.” Select “Configure”, make changes as desired, and select “Write.” Your radio is configured. Basic Commands Serial Port on PC Default to COM1. COM8.
COMMUNICATION CERTIFICATION LABORATORY (i) TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 76 of 103 Serial Number This unique number is predetermined by the manufacturer. (ii) Serial Baud Rate This is the baud rate the data radio uses to talk to a PC or external device. The default is 19,200 bits/second. Drop-down settings allow standard baud rates from 2400 to 19,200 bps.
COMMUNICATION CERTIFICATION LABORATORY (ix) TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 77 of 103 TX Assert The volume or amount of time the transmitting radio will collect or wait before it transmits. Default is 10 mS. (x) CD Level Carrier Detect level. Lets the scanning radio determine if there’s a valid signal to receive. This is a factory alignment setting. (xi) Group Code Lets you set any number of radios to the same group. There are 1400 available groups.
COMMUNICATION CERTIFICATION LABORATORY (xvii) TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 78 of 103 Test Frequency Lets you test the sending and receiving frequency of any two radios. The default is set to 915.0. Available frequencies are 902-928 MHz.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 79 of 103 Default Settings Serial Baud Rate…………………………………………………… 19,200 bits/second Preamble Length:…………………………………………………………………..180 mS RF Data Rate:………………………………………………………….……………… 50 uS RX buffer size:…………………………………………………………………… 64 bytes* TX buffer size:…………………………………………………………………… 50 bytes* CTS Assert:………………………………………………………………………… 32 bytes CTS De-assert:………………………………………………….
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 80 of 103 WWC Micro Hopper Data Radio Specifications General Specifications Power Source ………………………………………………………………..…. 5 VDC, 1.5 Watts Temperature …………………………………………………………………………. -40 to +80 °C Antenna Impedance ……………………………………………………… 50 Ohms unbalanced Antenna Connection …………………………………………………………………… SMA female Operation Mode …………………………………… Frequency Hopping Spread Spectrum Frequency Control ……………………………………..
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 81 of 103 WWC Micro HopperData Radio Radio Hardware Interface Mechanical Overview Molex 20 pin 2mm Connector P/N 87332-2020 2.470" 2.300" 20 19 TP1 P1 1.535" 2 1.705" 1 J1 Standard SMA Female 3 x 0.125" diameter holes World Wireless Communications, Inc.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 82 of 103 WWC Micro Hopper Data Radio Hardware Interface Pin Definitions for Connector J1 The following pin out summary is achieved through a 20 pin 2mm connector J1 (Molex P/N 87332-2020).
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 83 of 103 Mechanical Overview Molex 20 pin 2mm Connector P/N 87332-2020 2.470" 2.300" 20 19 Model: 900 uHopper T E L E M E T R Y & S C A D A DI V I S I O N P1 FCC ID: NQE-900UHOPPER 1.535" This device complies with Part 15 of the FCC rules.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 84 of 103 WWC Micro Hopper Data Radio Hardware Interface FCC Compliance Warning Changes or modifications to the Micro Hopper Data Radio not expressly approved by World Wireless Communications could void the user’s authority to operate this product. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 85 of 103 Glossary Baud CD Measurement of the signaling speed of a data transmission device. Carrier Detect level. Used to tell the scanning radio if a receiving radio is present. Communication (COM) Ports Designation of serial communications channels. COM port designations for this radio are COM1 through COM8. Configuration Default Operating characteristics of this data radio.
COMMUNICATION CERTIFICATION LABORATORY TEST REPORT: 73-6907 FCC ID: NQE-900UHOPPER Page 86 of 103 RF Data Rate How fast the transmitting radio sends data across the RF channel. RSSI RTS Receive Signal Strength Indicator. Indicates signal strength on any given frequency. Request to Send. A control signal used in conjunction with Clear to Send (CTS) to perform data flow control. RX Buffer Size Number of bytes in the receive buffer.