Use and Care Manual

ManualsBrandsWorkforce ManualsAir Compressors, Tools & AccessoriesHeavy-Duty Pistol Grip Grease Gun with 12 in. Flex Extension

Loading Your Grease Gun

L1320 L1325

L1310 L1350, L1355 L1355FZ

Cartridge Loading Suction Loadng Filler Pump Loading

Pull follower rod from barrel

and lock into place.

Pull follower rod from barrel

and lock into place.

WARNING:

Do not load gun with air operated

grease pump. Damage to unit

will occur and warranty

will be voided.

Unscrew barrel from head. Unscrew barrel from head. Wipe bulk ﬁller nipple until clean.

Remove cap from end

of grease cartridge

Insert open end of gun barrel

two inches below surface of grease.

Insert bulk ﬁller nipple

into loader pump receptacle.

Insert cartridge into barrel,

open end down.

Slowly pull back follower rod

to draw in grease. Pull follower rod

back all the way and lock into place.

Pump grease until 8 inches of follower rod

is exposed.

(Between the follower rod handle and barrel

cap)

Remove pull tab from top

of grease cartridge.

Make sure cartridge is pushed

down completely.

Screw barrel back into head.

Pump grease until barrel is full.

(When barrel is full, rod can be pulled out

without spring tension)

Screw barrel into head until snug. Unlock follower rod and push into barrel. Release follower rod.

Unscrew barrel slightly.

(Approximately two revolutions)

If no bleeder valve is installed,

unscrew barrel slightly.

(Approximately two revolutions)

(Skip this step if bleeder valve is installed)

Push follower rod into barrel.

Release follower rod. Release follower rod.

Prime.

(see “Priming Your Grease Gun”)

Push follower rod into barrel. Push follower rod into barrel.

Screw barrel into head.

Depress bleeder valve to release air.

(If bleeder valve is installed)

Prime.

(see “Priming Your Grease Gun”)

Prime.

(see “Priming Your Grease Gun”)

Begin greasing.

Begin greasing. Begin greasing.

Owner’s Instructions

Manually Operated Grease Guns

Part No. : L1320, L1325, L1310, L1350, L1355, L1355FZ

Legacy Manufacturing Company

Marion, IA, U.S.A.

Ph: 319.373.7305

Fx: 319.373.7309

service@legacymfg.com

legacymfg.com

INS1000

Published 11/15/2013 Revised 5/27/2016

Summary of content (10 pages)

PAGE 1
Owner’s Instructions Part No. : L1320, L1325, L1310, L1350, L1355, L1355FZ L1320 L1325 Manually Operated Grease Guns L1310 L1350, L1355 L1355FZ Loading Your Grease Gun Cartridge Loading Suction Loadng Filler Pump Loading WARNING: Do not load gun with air operated grease pump. Damage to unit will occur and warranty will be voided. Pull follower rod from barrel and lock into place. Pull follower rod from barrel and lock into place. Unscrew barrel from head. Unscrew barrel from head.
PAGE 2
Priming Your Grease Gun Point outlet up at least 45 degrees. Using slow, complete strokes, stroke handle repeatedly until grease flows without air. (Should require 10 - 20 strokes) Re-Priming Your Grease Gun Unscrew barrel approximately 2 revolutions. (Barrel should be loose, but still attached to head) Pull follower rod out and push back into barrel to compress grease and expel air. Repeat several times. Screw barrel back into head. Prime. Greasing a Zerk (Grease Fitting) Press coupler onto zerk.
PAGE 3
Troubleshooting Your Grease Gun Problem Grease does not flow when handle is stroked. Grease leaks between gun head and extension or extension and coupler. Grease leaks from coupler body joint or between coupler jaws and grease fitting.
PAGE 4
PAGE 5
Instructivo del propietario Componente Núm. : L1320, L1325, L1310, L1350, L1355, L1355FZ L1320 L1325 Pistolas graseras operadas manualmente Cómo cargar la pistola grasera L1310 Instalación del cartucho L1350, L1355 Carga del aspirador L1355FZ Carga de la bomba de llenado ADVERTENCIA: No cargue la pistola con una bomba de grasa operada con aire. De hacerlo esto así se pudiera dañar la unidad e invalidar su garantía. Jale la varilla del cilindro y engánchela en su posición.
PAGE 6
Cómo cebar la pistola grasera Apunte la salida hacia arriba al menos 45 grados. Utilizando carreras lentas y completas, bombee la empuñadura repetidamente hasta que salga grasa sin aire. (Aproximadamente 10 a 20 carreras) Cómo volver a cebar la pistola grasera Desenrosque el cilindro aproximadamente 2 vueltas. (El cilindro debe estar suelto, pero enroscado en la cabeza) Tire de la varilla del impulsor y empuje dentro del cilindro para comprimir la grasa y expulsar el aire. Repita varias veces.
PAGE 7
Solución de problemas de la pistola grasera Problema La grasa no fluye al bombear la empuñadura: Fugas de grasa entre la cabeza de la pistola y la extensión o la extensión y el acoplador. La grasa se fuga de la junta del acoplador o entre las mordazas del acoplador y el engrasador. Causa(s) Remedio Es necesario volver a cebar la pistola (consulte "Cómo volver a cebar la pistola grasera") No le quitó la tapa al cartucho de grasa.
PAGE 8
Instructions d’utilisation Réf.: L1320, L1325, L1310, L1350, L1355, L1355FZ L1320 L1325 Manually Operated Grease Guns Chargement de la pompe à graisse Chargement de la cartouche L1310 Chargement par aspiration L1350, L1355 L1355FZ Chargement par pompe de remplissage Tirer la tige de poussée hors du corps et la bloquer. Tirer la tige de poussée hors du corps et la bloquer. AVERTISSEMENT : Ne pas charger le pistolet à l'aide d’une pompe à graisse pneumatique.
PAGE 9
Amorçage de la pompe à graisse Pointer la buse vers le haut d'un angle d'au moins 45 degrés. Actionner lentement le levier à fond de façon répétée jusqu'à ce que la graisse s'écoule sans air. (Nécessite normalement 10 à 20 coups de leviers) Réamorçage de la pompe à graisse Dévisser le corps de pompe de 2 tours environ. (Le corps doit être desserré, mais toujours attaché à la tête) Tirer la tige de piston hors du corps et la renfoncer pour comprimer la graisse et expulser l'air. Répéter plusieurs fois.
PAGE 10
Dépannage de la pompe à graisse Problème Cause(s) Mesure corrective La pompe doit être réamorcée. Il ne s'écoule pas de graisse lorsque la poignée est actionnée. Fuite de graisse entre la tête de pompe et la rallonge ou entre la rallonge et le coupleur.