Use and Care Manual

ManualsBrandsWorker ManualsTools & Hardware10-Amp 7 in. Corded Variable Speed Polisher/Sander

45134 03/2017

VARIABLE SPEED POLISHER

ALIFORNIA PROPOSITION 65

ARNING: You can create dust

hen you cut, sand, drill or grind

aterials such as wood, paint,

etal, concrete, cement, or other

asonry. This dust often contains

emicals known to cause cancer,

irth defects, or other reproductive

arm. Wear protective gear.

ARNING: This product or its

ower cord may contain

emicals, including lead, known

o the State of California to cause

ncer and birth defects or other

eproductive harm. Wash hands

fter handling.

mportant!

hen using equipment, a few safety

recautions must be observed to

oid injuries and damage. Please

ead the complete operating manual

ith due care. Keep this manual in a

afe place, so that the information is

ailable at all times. If you give the

uipment to any other person, give

hem these operating instructions as

ell. We accept no liability for

amage or accidents which arise due

o non-observance of these

nstructions and the safety information

erein.

SPECIFICATIONS

Motor: 120V ~ 60Hz, 9.2 Amp

No-Load Speed: 200 - 3,350 RPM

Buffing Diameter: 7

Keep this manual and receipt in

a safe and dry place for future

reference.

GENERAL SAFETY RULES

WORK AREA

KEEP THE WORK AREA CLEAN

AND WELL LIT. Cluttered benches

and dark areas increases the risk

of injury.

DO NOT OPERATE THE TOOL

IN EXPLOSIVE ATMOSPHERES,

such as in the presence of

flammable liquids, gases, or dust.

The tool may create a spark that

could ignite flammable liquids,

gases, or dust.

KEEP VISITORS AWAY. Do not

let visitors handle the tool. All

visitors should be kept safely

away from the work area.

NEVER ENGAGE IN

HORSEPLAY WITH THE TOOL.

Respect the tool as a working

implement.

PERSONAL SAFETY

OPERATORS AND OTHERS IN

WORK AREA MUST WEAR

SAFETY GLASSES WITH SIDE

SHIELDS. Safety glasses must

conform to ANSI Z87.1

specifications.

Models: 45134

For Customer Service, please call 1-800-348-5004 or

email feedback@natitools.com

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this

product. Observe all safety information to protect yourself and others. Failure to observe the instructions may

result in property damage and/or personal injury. Please keep instructions for future reference.

Important Operating Instructions

For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.

Summary of content (11 pages)

PAGE 1
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property damage and/or personal injury. Please keep instructions for future reference.
PAGE 2
ALWAYS WEAR EAR AND HEAD PROTECTION. Wear ear protection to protect your ears from loud noises. Wear head protection to protect your head from flying objects. USE SAFETY EQUIPMENT. A dust mask, non-skid safety shoes, and a hard hat must be used for the applicable conditions. Wear a full face shield if you are producing metal filings or wood chips. DRESS PROPERLY. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts.
PAGE 3
DISCONNECT THE PLUG FROM THE POWER SOURCE BEFORE MAKING ANY ADJUSTMENTS, CHANGING ACCESSORIES, OR STORING THE POWER TOOL. This will reduce the risk of accidental starting. USE THE POWER TOOL THE WAY IT WAS INTENDED. Use of the power tool for operations different could result in a hazardous situation. WARNING: The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.
PAGE 4
SETUP Installing the Auxiliary Handles WARNING: To prevent serious injury: Do not operate this tool without the auxiliary handle properly installed. OPTION 2: Using with a side handle (side handle not included) Workpiece and Work area set up This tool can be used with many standard angle grinder side handles which can be installed on either side. 1. Designate a work area that is clean and well-lit. The work area must be accessible by children or pets to prevent distraction and injury.
PAGE 5
4. Rotate the speed dial to select the desired speed between 1 & 4. Caution: Only use the slower speeds (1 through 4) for polishing. Otherwise, damage may occur to the paint being polished. NATI is not responsible for damage to the vehicle s finish due to improper use of this Polisher. 5. Plug the power cord into an electrical extension cord (not included). Then, plug the extension cord into a grounded, GFCIprotected, 120 Volt electrical outlet.
PAGE 6
CLEANING, MAINTENANCE, & LUBRICATION 1. Before each use, inspect the general condition of the tool. Check for: parts its safe operation 2. After use, wipe external surfaces of the tool with a clean cloth. 3. Periodically blow dust and grit out of the motor vents using dry compressed air. Wear ANSIapproved safety goggles and NIOSH-approved breathing protection while doing this. 4. Periodically recheck all nuts, bolts, and screws for tightness. 5.
PAGE 7
VARIABLE SPEED CAR POLISHER Model: 45134 FUNCTIONAL DESCRIPTION AND SPECIFICATIONS WARNING: Disconnect the tool from the power source before making any adjustments, changing accessories or storing the tool. Such precautionary safety measures reduce the risk of unintentional tool operation. For Customer Service, please call 1-800-348-5004 or email feedback@natitools.
PAGE 8
Troubleshooting Guide Symptom Possible Cause(s) Cord not connected Corrective Action Check that the cord is plugged in No power at outlet Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure the circuit is right capacity for tool and circuit has no other loads. Internal Damage or wear Replace carbon brushes and/or have technician service tool Excess pressure applied to workpiece. Decrease pressure, allow tool to do the work.
PAGE 9
North American Tool Industries (NATI) makes every effort to ensure that this product meets high quality and durability standards. NATI warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, or accidents, repairs or alterations, or a lack of maintenance.
PAGE 10
7 VARIABLE SPEED CAR POLISHER Model: 45134 Parts List For Customer Service, please call 1-800-348-5004 or email feedback@natitools.
PAGE 11
# Description QTY. # Description QTY.