MODEL WSP-R242 (2inch Mobile Printer) Rev. 1.0 WOOSIM SYSTEMS Inc. (#501, Daerung Technotown 3th) 115, Gasan digital 2-ro, Geumcheon-gu, Seoul, 153-772 Rep. of KOREA Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
WSP-R242 Rev. 1.0 Copyright WSP-R242 2inch mobile printer operator’s manual. Copyright ⓒ2015 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
WSP-R242 Rev. 1.0 Introduction The WSP-R242 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of WSP-R242 printer are as follows: Compact size (79.2 x 123 x 45.6mm) Light weight(231g) for true mobility Very silent printing thru direct thermal printing method High speed (100mm/sec, MAX) High resolution(203dpi : 8dots/mm). USB, Bluetooth Ver3.
WSP-R242 Rev. 1.0 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
WSP-R242 Rev. 1.0 Federal Communications Commission Radio Frequency Interference Statement FCC ID : QDDWSP-R242 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WSP-R242 Rev. 1.0 CONTENTS 1. Outline. .........................................................................................................................................8 1.1. Model classifications. .......................................................................................................8 1.2 Product Part Number System ..........................................................................................8 1.3. Specifications. ........................................................
WSP-R242 Rev. 1.0 5.2. The self test ......................................................................................................................27 5.3. Using the Belt clip ..........................................................................................................27 6. Consumable Parts. ...................................................................................................................28 6.1. Recommended paper. ........................................................
WSP-R242 Rev. 1.0 1. Outline. 1.1. Model classifications. ( WSP-R242 ) ( ) Model Interface C1 : USB/Bluetooth (Standard) Power None : DC 8.4V 1.2 Product Par t Number System Model name / Interface Spec. Wired S40 SC30 W25 . . . Example) 1. Porti-S40 Wireless A RS-232C 1 Bluetooth B TTL 2 IrDA C USB 3 Wireless LAN D RS-485 0 None E Parallel Z None Serial/Bluetooth Part No. ⇒ S40/A1 2. Porti-SC30 Bluetooth Only Part No.
WSP-R242 Rev. 1.0 1.3. Specifications.
WSP-R242 Rev. 1.0 Item Specifications Battery Rechargeable 7.4V DC, 1100mAh (Li-ion) Battery duration 1 hour continuous printing Battery charger Environment conditions MCBF (Mean Cycle Between Failure) Input (100~250V AC, 50~60Hz) Output(8.4VDC/0.8A), 4hours full charge time Temperature Humidity Head -10°C ~ 50°C (operating) -10°C ~ 70°C (storage) 30% - 80% (operating) 10% - 90% (storage) Approximately 100Km < Table 1 > http://www.woosim.
WSP-R242 Rev. 1.0 2. Setting up the printer. 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Communication cable Battery charger adaptor WSP-R242 Battery Pack Thermal roll paper Belt clip ▼ OPTIONAL Smart Card Reader 2 SAM http://www.woosim.
WSP-R242 Rev. 1.0 2.2. Printer Features ▶ Part Name http://www.woosim.
WSP-R242 Rev. 1.0 2.3. Dimensions http://www.woosim.
WSP-R242 Rev. 1.0 2.4. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the picture. 3. Insert a new paper roll as shown. 4.
WSP-R242 Rev. 1.0 2.5. Power supply 2.5.1. Specified power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.5.2. Installing the batter y NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer.
WSP-R242 Rev. 1.0 2.5.3. Recharging the batter y pack For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
WSP-R242 Rev. 1.0 2.6. Set operation mode In keeping on pressing the Feed and Power button simultaneously until after the LCD Backlight(blue) blinks 5 times, the printer comes out at the circumstance to change the printer mode. (refer Table 2) FEED button : changing Printer MODE status. POWER button : changing OPTION status. *Note No additional mode settings are required to connect Android or iOS devices.
WSP-R242 Rev. 1.0 [Example] The defaults of the printer are : USB / Density Low / Mark No Use / Sensor High / PWDN 5 min slp If a user wants to modify the defaults with Bluetooth / Density High / Mark Use / Sensor Low / PWDN No Use Press FEED & POWER Button during the LCD backlight flickers 5 times. You will see present COMMUNICATION mode in the LCD. (USB) Press the POWER Button twice. And then, interface mode has set to Bluetooth mode. When you press FEED button once.
WSP-R242 Rev. 1.0 2.6.1. GAP/HOLE SENSOR SETTING 1. Set Mark as GAP / HOLE on mode setting. 2. If feed button keeps being pressed during self “SENSOR SETTING” appears on LCD window and paper keeps coming out “SENSOR SETTING”. 3. If feed button is not pressed after printing more than 3 pages of label 4. Setting is completed as Green and Red LED flash and “COMPLETE” appears on LCD window. ** Caution : Sensor setting stops if the feed button is not pressed during self test. http://www.woosim.
WSP-R242 Rev. 1.0 2.7. Memor y switch table Mode 2 3 4 Etc. Mode Option 1 USB 1 No use 2 USB(Pro) 2 1min Sleep 3 Bluetooth 3 2min Sleep 4 Bluetooth(Pro) 4 3min Sleep 5 Bluetooth(iAP) 5 4min Sleep 1 Low 6 5min Sleep 2 Medium 7 1min Off 3 High 8 2min Off 1 No use 9 3min Off 2 Use 10 4min Off 3 Gap / Hole V 11 5min Off 4 Back V 1 Low Sensor 2 Medium1 sensitivity 3 Medium2 4 High Communi1 Option cation Port Density Mark V 5 Power Down Etc.
WSP-R242 Rev. 1.0 3. Interface 3.1. USB The WSP-R242 printer has a USB interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: Pin No. Name Function 1 VCC +5V 2 DM DATA “-” 3 DP DATA “+” 4 NC. - 5 GND Ground NOTE : ● If you connect the printer interface cable is converted to USB mode. ● When data receiving, when it removes the communication cable, it loses a data. 3.2.
WSP-R242 Rev. 1.0 3.3. Magnetic Card Reading ▶ Check the direction of the magnetic stripe card and reading. ▶ Cards can be read in both directions. ▶ If the reading is successful, the card buzzer once, beep three times if it fails. http://www.woosim.
WSP-R242 Rev. 1.0 4. Smar t Card Reader Module 4.1. General Spec. Contact Smart Card Reader Module for ISO/IEC-7816 Support Asynchronous Protocol T=0,T=1 Smart Card Connection - Short Circuit Current Limitation - 6KV ESD Protection on whole Smart Card Interface - Connector : Friction Type with Smart Card presence detection 2 SAM (Security Application Module) EMV Level 1 Certified 4.2.
WSP-R242 Rev. 1.0 4.3. Inser ting the IC card ▶ Check the contact IC chip and the card in the direction of the arrow insert. http://www.woosim.
WSP-R242 Rev. 1.0 4.4. Communication Protocol Sequence 4.4.1. Regular Operation Host Command Module Execution Response 4.4.2. Irregular Operation (Communication Error) 500ms timeout Host Command Command Module Host Command Command is Executio canceled n Command Command Error Module CheckSumEr Executio r n http://www.woosim.
WSP-R242 Rev. 1.0 5. Using the printer 5.1. Control panel. BUTTON - FEED Button : Use to feed paper continuously. - POWER Button : ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions.
WSP-R242 Rev. 1.0 5.2. The self test Self-Test prints out the current setting value of printer. The way of self-test is as follows. 1. Insert proper paper into the printer. 2. Power on while pressing feed button to start self-test. 3. Printer will print out the current status. (F/W version and set contents) 4. And then pattern of characters will be printed out. 5. Self-test will be finished automatically and turned to the standby status.
WSP-R242 Rev. 1.0 6. Consumable Par ts. 6.1. Recommended paper. Type : Thermal Paper Paper width : 58mm Paper thickness : 60±5㎛ Outer diameter : Ø40mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃.
WSP-R242 Rev. 1.0 7. Revision Histor y Date Version Oct. 13. 2015 1.0 Comments Initialize http://www.woosim.