MODEL WSP-R241 (2inch Mobile Printer) Rev. 1.0 WOOSIM SYSTEMS Inc. (#501, Daerung Technotown 3th) 115, Gasan digital 2-ro, Geumcheon-gu, Seoul, 153-772 Rep. of KOREA Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
WSP-R241 Rev. 1.0 Copyright WSP-R241 2inch mobile printer operator’s manual. Copyright ⓒ2014 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
WSP-R241 Rev. 1.0 Introduction The WSP-R241 is suitable designed for use with a growing variety of mobile devices. Bluetooth/Serial interfaces make the WSP-R241 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of WSP-R241 printer are as follows: Pocket size (79.5 X 114.3 X 43.5mm) Light weight (201g) for true mobility. Very silent printing thru direct thermal printing method.
WSP-R241 Rev. 1.0 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
WSP-R241 Rev. 1.0 Federal Communications Commission Radio Frequency Interference Statement FCC ID : QDDWSP-R241 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WSP-R241 Rev. 1.0 CONTENTS 1. Outline...........................................................................................................................................7 1.1. Model classifications ..........................................................................................................7 1.2. Product Part Number System ...........................................................................................7 1.3. Specifications. ....................................................
WSP-R241 Rev. 1.0 1. Outline 1.1. Model classifications WSP-R241 ( ) ( ) Model Interface A1:USB/Bluetooth Power None : DC 8.4V 1.2. Product Par t Number System Model name / Wired S40 SC30 W25 Example) 1. Porti-S40 Interface Spec. Wireless A RS-232C 1 Bluetooth B TTL 2 IrDA 0 None . C USB D RS-485 . E Parallel . Z None UART/Bluetooth Part No. ⇒ S40/A1 2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported.
WSP-R241 Rev. 1.0 1.3. Specifications.
WSP-R241 Rev. 1.0 Item MSR [option] Specification Triple tracks (1&2&3 Tracks Reading) *Supports 3DES & AES encryption Battery Rechargeable 7.4V DC , 1100mAh (Li-ion) Battery duration 1 hour continuous printing Battery Charger Input (100~240V AC 50/60Hz) Output(8.4VDC/0.8A), 4hours full charge time Temperature Environment Conditions Humidity Limited Warranty of Life Head -10°C ~ 50°C (operating) -10°C ~ 70°C (storage) 30% - 80% (operating) 10% - 90% (storage) 100Km < Table 1 > http://www.
WSP-R241 Rev. 1.0 2. Setting up the printer 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Thermal roll paper Battery Pack WSP-R241 Belt Clip Battery charger adaptor Communication cable ▼ OPTIONAL External Battery Car charger MSR Cradle http://www.woosim.
WSP-R241 Rev. 1.0 2.2. Printer Features ▶ Part Name [MSR Model] http://www.woosim.
WSP-R241 Rev. 1.0 2.3. Dimensions ▶ Standard Model http://www.woosim.
WSP-R241 Rev. 1.0 ▶ MSR Model http://www.woosim.
WSP-R241 Rev. 1.0 2.4. Replacing the paper roll Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the picture. 3. Insert the paper roll as shown. 4.
WSP-R241 Rev. 1.0 2.5. Power supply 2.5.1. Internal power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.5.2. Installing the Batter y NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer.
WSP-R241 Rev. 1.0 2.5.3. Recharging the batter y For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. Insert the Battery charger adaptor to the charge connector of the External Battery Cradle. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
WSP-R241 Rev. 1.0 2.6. Set operation mode In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode. (refer to Table 2) ** Only the printer which support iOS Bluetooth interface comes out at the circumstance to change the printer mode. (Bluetooth Mode or Boluetooth(iAP) Mode). ** Manipulation methods : 1.
WSP-R241 Rev. 1.0 POWER button : use for changing OPTION status. (Error Lamp) FEED button : use for changing MODE status.
WSP-R241 Rev. 1.0 When you press FEED Button once again, Power Lamp flickers 5 times and Error Lamp flickers once. Press POWER Button once, Error Lamp flickers twice. And then the density has set to 2 stop bit. When you press FEED Button once again, Power Lamp flickers 6 times and Error Lamp flickers once. Press POWER Button twice, Error Lamp flickers 3 times. And then the density has set to Density high.
WSP-R241 Rev. 1.
WSP-R241 Rev. 1.0 MODE POWER Lamp ERROR Lamp (Green) (Red) Power Down 9 Option 1 No use 2 1 minute 3 2 minute 4 3 minute 5 4 minute 6 5 minute < Table 2 > Notice : Bluetooth(iAP) is the mode which is used in iPod, iPhone and iPad Whole aspect. http://www.woosim.
WSP-R241 Rev. 1.0 3. Interface 3.1. USB (Fig.3.1) The WSP-R241 printer has a USB interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: USB Pin No. Name Function 1 VCC +5V 2 DM DATA “-” 3 DP DATA “+” 4 NC. - 5 GND Ground NOTE : ● If you connect the printer interface cable is converted to USB mode. ● When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.
WSP-R241 Rev. 1.0 3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth Ver3.0 + EDR / Class2 (10m) Frequency band 2.4GHz Protocol L2CAP, RFCOMM, SDP Profile GAP, SDAP, SPP 3.3. Card Reading Please take notice that Magnetic Stripe Card should be swapped in direction of arrow. Card can be read in both http://www.woosim.
WSP-R241 Rev. 1.0 4. Using the printer 4.1. Control panel (Fig.4.1) Button - FEED Button: When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button: ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions .
WSP-R241 Rev. 1.0 LAMP - Power : Printer is ON and ready to receive data. (GREEN) - Error : Indicates a fault condition or a printer error. (RED) (details: no paper, paper cover opened. etc.) - Bluetooth : Indicates a Bluetooth connection status. (BLUE) - Battery Power : These lamps(Green) indicated the battery power remaining. (GREEN) The battery gain in quantity and these lamps are on the decrease. If so, you must recharge the battery by using the battery charger. 4.2.
WSP-R241 Rev. 1.0 4.3. Using the Belt clip Following the instruction of the arrow, please put the belt clip in the hole and turn and fix the screw to the right by using a thing like a coin. Afterward, you can use it like the picture below http://www.woosim.
WSP-R241 Rev. 1.0 5. Consumable Par ts 5.1. Recommended paper Type : Thermal Paper Paper width : 58mm Paper thickness : 60±5㎛ Outer diameter : Ø40mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core, and the roll paper which has near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70 ℃.
WSP-R241 Rev. 1.0 6. Revision Histor y Date Version Oct. 20. 2014 1.0 Comments Initialize http://www.woosim.