MODEL WSP-R240 (2inch Mobile Printer) Rev. 6.1 WOOSIM SYSTEMS Inc. (#501, Daerung Technotown 3th) 115, Gasan digital 2-ro, Geumcheon-gu, Seoul, 153-772 Rep. of KOREA Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
WSP-R240 Rev. 6.1 Copyright WSP-R240 2inch mobile printer operator’s manual. Copyright ⓒ2014 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
WSP-R240 Rev. 6.1 Introduction The WSP-R240 is suitable designed for use with a growing variety of mobile devices. Bluetooth/Serial interfaces make the WSP-R240 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of WSP-R240 printer are as follows: Pocket size (79.5 X 114.3 X 43.5mm) Light weight (201g) for true mobility. Very silent printing thru direct thermal printing method.
WSP-R240 Rev. 6.1 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
WSP-R240 Rev. 6.1 Federal Communications Commission Radio Frequency Interference Statement FCC ID : QDDWSP-R240X This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WSP-R240 Rev. 6.1 CONTENTS 1. Outline ................................................................................................................................... 7 1.1. Model classifications .................................................................................................... 7 1.2 Symbol ............................................................................................................................ 7 1.2. Product Part Number System........................................
WSP-R240 Rev. 6.1 1. Outline 1.1. Model classif ications WSP-R240 ( ) ( ) Model Interface A1:UART/Bluetooth Power None : DC 8.4V 1.2 Symbol Standby symbol IEC 5009, the standby symbol(line partially within a broken circle), Indicates a sleep mode or low power state. Direct current symbol This symbol is found on many electronic devices that either require or produce direct current. http://www.woosim.
WSP-R240 Rev. 6.1 1.2. Product Par t Number System Model name S40 SC30 W25 Example) 1. Porti-S40 / Interface Spec. Wired Wireless A RS-232C 1 Bluetooth B TTL 2 IrDA 0 None . C USB D RS-485 . E Parallel . Z None UART/Bluetooth Part No. ⇒ S40/A1 2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported.
WSP-R240 Rev. 6.1 1.3. Specif ications.
WSP-R240 Rev. 6.1 Item MSR [option] Specification Triple tracks (1&2&3 Tracks Reading) *Supports 3DES & AES encryption Battery Rechargeable 7.4V DC , 1130mAh (Li-ion) Battery duration 1 hour continuous printing Battery Charger Environment Conditions MCBF (Mean Cycle Between failure) Input (100~250V AC 50~60Hz) Output(8.4VDC/0.
WSP-R240 Rev. 6.1 2. Setting up the printer 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Battery Pack Thermal roll paper WSP-R240 Belt Clip Battery charger adaptor Communication cable ▼ OPTIONAL External Battery Cradle MSR http://www.woosim.
WSP-R240 Rev. 6.1 2.2. Printer Features ▶ Part Name None MSR Model MSR Model http://www.woosim.
WSP-R240 Rev. 6.1 ▶ Dimensions [Unit : mm] None MSR Model MSR Model http://www.woosim.
WSP-R240 Rev. 6.1 2.3. Replacing the paper roll Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the picture. 3. Insert the paper roll as shown. 4.
WSP-R240 Rev. 6.1 2.4. Power supply 2.4.1. Internal power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the Batter y NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer.
WSP-R240 Rev. 6.1 2.4.3. Recharging the batter y For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. Insert the Battery charger adaptor to the charge connector of the External Battery Cradle. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
WSP-R240 Rev. 6.1 2.5. Set operation mode In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode. (refer to Table 2) *Note No additional mode settings are required to connect Android or iOS devices. ** If you want to change the Bluetooth Mode of printer, you need to disconnect the Bluetooth function of the current paired Smartphone. ** Methods : 1.
WSP-R240 Rev. 6.1 POWER button : use for changing OPTION status. (Error Lamp) FEED button : use for changing MODE status.
WSP-R240 Rev. 6.1 When you press FEED Button once again, Power Lamp flickers 5 times and Error Lamp flickers once. Press POWER Button once, Error Lamp flickers twice. And then the density has set to 2 stop bit. When you press FEED Button once again, Power Lamp flickers 6 times and Error Lamp flickers once. Press POWER Button twice, Error Lamp flickers 3 times. And then the density has set to Density high.
WSP-R240 Rev. 6.
WSP-R240 Rev. 6.1 MODE Power Down POWER Lamp ERROR Lamp (Green) (Red) 9 Option 1 No use 2 1 minute 3 2 minute 4 3 minute 5 4 minute 6 5 minute < Table 2 > Notice : Bluetooth(iAP) is the mode which is used in iPod, iPhone and iPad Whole aspect. http://www.woosim.
WSP-R240 Rev. 6.1 3. Inter face 3.1. UART (Fig.3.1) The WSP-R240 printer has a UART interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: UART Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 GND - Ground 4 NC. - - 5 GND - Ground NOTE : ● If you connect the printer interface cable is converted to UART mode.
WSP-R240 Rev. 6.1 3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth Ver3.0 / Class2 (10m) Frequency band 2402~2480 MHz Protocol L2CAP, RFCOMM, SDP Profile GAP, SDAP, SPP 3.3. Card Reading Please take notice that Magnetic Stripe Card should be swapped in direction of arrow. Card can be read in both http://www.woosim.
WSP-R240 Rev. 6.1 4. Using the printer 4.1. Control panel (Fig.4.1) Button - FEED Button: When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button: ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions.
WSP-R240 Rev. 6.1 LAMP - Power : Printer is ON and ready to receive data. (GREEN) - Error : Indicates a fault condition or a printer error. (RED) (details: no paper, paper cover opened. etc.) - Bluetooth : Indicates a Bluetooth connection status. (BLUE) - Battery Power : These lamps(Green) indicated the battery power remaining. (GREEN) The battery gain in quantity and these lamps are on the decrease. If so, you must recharge the battery by using the battery charger. 4.2.
WSP-R240 Rev. 6.1 4.3. Using the Belt clip Following the instruction of the arrow, please put the belt clip in the hole and turn and fix the screw to the right by using a thing like a coin. Afterward, you can use it like the picture below http://www.woosim.
WSP-R240 Rev. 6.1 5. Consumable Par ts 5.1. Recommended paper Type : Thermal Paper Paper width : 58mm Paper thickness : 60±5㎛ Outer diameter : Ø40mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core, and the roll paper which has near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70 ℃.