MODEL WSP-i350 (3inch Rugged Mobile Printer) Rev. 4.1 WOOSIM SYSTEMS Inc. (#501, Daerung Technotown 3th) 115, Gasan digital 2-ro, Geumcheon-gu, Seoul, 153-772 Rep. of KOREA Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
WSP-i350 Rev. 4.1 Copyright WSP-i350 3inch Rugged Mobile printer operator’s manual. Copyright ⓒ2016 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
WSP-i350 Rev. 4.1 Introduction The WSP-i350 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of WSP-i350 printer are as follows: Compact size (120×130.5×58.4mm) Light weight(395g) for true mobility [standard] Very silent printing thru direct thermal printing method High speed (120mm/sec, MAX) High resolution(203dpi : 8dots/mm). UART, Bluetooth Ver3.0, Wireless LAN(IEEE802.
WSP-i350 Rev. 4.1 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
WSP-i350 Rev. 4.1 Federal Communications Commission Radio Frequency Interference Statement FCC ID : QDDWSP-I350X This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WSP-i350 Rev. 4.1 CONTENTS 1. Outline. .................................................................................................................................. 8 1.1. Model classifications. .................................................................................................. 8 1.2 Product Part Number System ..................................................................................... 9 1.3. Specifications. ......................................................................
WSP-i350 Rev. 4.1 5.1. Recommended paper. ............................................................................................... 30 5.2. Printing position. ....................................................................................................... 30 6. Revision History ............................................... 오류! 책갈피가 정의되어 있지 않습니다. http://www.woosim.
WSP-i350 Rev. 4.1 1. Outline. 1.1. Model classif ications. WSP-i350 ( ) ( ) Model Interface A1 : UART/Bluetooth (Standard) Power None : DC 8.4V 1.2 Symbol Standby symbol IEC 5009, the standby symbol(line partially within a broken circle), Indicates a sleep mode or low power state. Direct current symbol This symbol is found on many electronic devices that either require or produce direct current. http://www.woosim.
WSP-i350 Rev. 4.1 1.3 Product Par t Number System Model name / Interface Spec. Wired S40 SC30 A RS-232C 1 Bluetooth W25 B TTL 2 IrDA C USB 3 Wireless LAN D RS-485 0 None E Parallel Z None . . . Example) 1. Porti-S40 Wireless Serial/Bluetooth Part No. ⇒ S40/A1 2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported.
WSP-i350 Rev. 4.1 1.4. Specif ications.
WSP-i350 Rev. 4.1 Item Specifications MSR [option] 1&2 or 2&3 Track Reading LCD 128×32 Dots FSTN (Blue LED Backlight) Battery Rechargeable 7.4V DC, 1,800mAh /2200mAh (Li-ion) Battery duration 1 hour continuous printing Battery charger Environment conditions MCBF(Mean Cycle Between Failure) Input (100~250V AC, 50~60Hz) Output(8.4VDC/0.
WSP-i350 Rev. 4.1 2. Setting up the printer. 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Communication cable Thermal roll paper Battery charger adaptor Belt clip WSP-i350 Battery Pack ▼ OPTIONAL MSR Shoulder strap http://www.woosim.
WSP-i350 Rev. 4.1 2.2. Printer Features Standard model MSR model http://www.woosim.
WSP-i350 Rev. 4.1 2.3. Dimensions ▶ Standard model 120 58.4 130.5 http://www.woosim.
WSP-i350 Rev. 4.1 ▶ MSR model 120 58.4 132.5 http://www.woosim.
WSP-i350 Rev. 4.1 2.4. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the picture. 3. Insert a new paper roll as shown. 4.
WSP-i350 Rev. 4.1 2.5. Power supply 2.5.1. Specified power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.5.2. Installing the batter y NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer.
WSP-i350 Rev. 4.1 2.5.3. Recharging the batter y pack For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
WSP-i350 Rev. 4.1 2.6. Set operation mode In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode. (refer Table 2) *Note No additional mode settings are required to connect Android or iOS devices. ** If you want to change the Bluetooth Mode of printer, you need to disconnect the Bluetooth function of the current paired Smartphone. ** Methods : 1.
WSP-i350 Rev. 4.1 FEED button : changing Printer MODE status. (Power Lamp) POWER button : changing OPTION status.
WSP-i350 Rev. 4.1 When you press FEED button once. You will see present Quality mode in the LCD. (Low) Press POWER Button once. And then the quality has set to Quality high. When you press FEED button once. You will see present MARK mode in the LCD. (Use) Press POWER Button once. And then the mark has set to Mark no use. When you press FEED button once. You will see present SENSOR mode in the LCD. (High) Press POWER Button once. And then the sensor has set to Sensor Low.
WSP-i350 Rev. 4.1 MODE Communication Port OPTION Bluetooth WLAN UART UART Protocol UART Protocol UART Bluetooth WLAN Protocol Bluetooth Protocol WLAN Bluetooth(iAP) 9600 bps 19200 bps Baud Rate 38400 bps 57600 bps 115200 bps Data Bit 7 Data bit 8 Data bit No Parity Parity Bit Odd Parity Even Parity Stop Bit 1 Stop bit 2 Stop bit Density Low Density Medium Density Density High Density High+1 Density High+2 Quality Mark Low High No use Use Continue… http://www.woosim.
WSP-i350 Rev. 4.1 MODE OPTION Low Sensor Medium1 Medium2 High No use 1min Sleep 2min Sleep 3min Sleep 4min Sleep Power Down 5min Sleep 1min Off 2min Off 3min Off 4min Off 5min Off < Table 2 > Notice : Bluetooth(iAP) is the mode which is used in iPod, iPhone and iPad Whole aspect. http://www.woosim.
WSP-i350 Rev. 4.1 2.7. Conf irmation of the Wireless-LAN information 2.7.1. MAC Address printing MAC address which is set to the printer can be printed out in pressing the Power and Feed button simultaneously and taking off them shortly after the ERROR lamp blinks 2.7.2. Confirmation of the Wireless-LAN setting information Press the Power button in the printer turning on As the LCD backlight turns on, MAC Address is indicated.
WSP-i350 Rev. 4.1 3. Inter face 3.1. UART The WSP-i350 printer has a UART interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: ① UART Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 GND - Ground 4 NC. - - 5 GND - Ground NOTE : ● If you connect the printer interface cable is converted to UART mode.
WSP-i350 Rev. 4.1 3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth Ver3.0 / Class2 (10m) Frequency band 2402~2480㎒ Protocol L2CAP, RFCOMM, SDP Profile GAP, SDAP, SPP 3.3. Wireless L AN Category Specification Function Radio frequency transfer Module (IEEE802.11b/g/n standard conformity) Frequency band 2.4GHz Channel 1 to 13 channel Security WEP(64/128), WPA(TKIP), WPA2(AES) 3.4.
WSP-i350 Rev. 4.1 4. Using the printer 4.1. Control panel. BUTTON - FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button: ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions.
WSP-i350 Rev. 4.1 4.2. The self test Self-Test prints out the current setting value of printer. The way of self-test is as follows. 1. Insert proper paper into the printer. 2. Power on while pressing feed button to start self-test. 3. Printer will print out the current status. (ROM version and communication mode) 4. And then pattern of characters will be printed out. 5. Self-test will be finished automatically and turned to the standby status.
WSP-i350 Rev. 4.1 4.3.2. Using the Belt clip Following the instruction of the arrow, please put the belt clip in the hole and turn and fix the screw to the right by using a thing like a coin. Afterward, you can use it like the picture below http://www.woosim.
WSP-i350 Rev. 4.1 5. Consumable Par ts. 5.1. Recommended paper. Type : Thermal Paper Paper width : 80mm Paper thickness : 60±5㎛ Outer diameter : Ø50mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃.