MODEL WSP-i350 (3inch Industrial Printer) WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com http://www.woosim.
Copyright WSP-i350 3inch Industrial printer operator’s manual. Copyright ⓒ2009 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
Introduction The WSP-i350 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of WSP-i350 printer are as follows: X Pocket size (120× 130.5× 58.3mm) X Light weight(520g) for true mobility X Very silent printing thru direct thermal printing method X High speed (60mm/sec, MAX) X UART(RS-232C or TTL), IrDA Ver1.1, Bluetooth Ver2.0 interface Wireless LAN interface(IEEE802.
Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
CONTENTS Copyright .....................................................................................................................................2 Trademark ....................................................................................................................................2 Caution.........................................................................................................................................2 Operating Precautions ..............................................
1. Outline. 1.1. Model classifications. ( WSP-i350 ) ( ) Model Interface None: UART/Bluetooth A2 : UART/IrDA Power None : DC 8.4V 1.2. Product Part Number System. Model name . . 2. Porti-SC30 Interface Spec. Wired S40 SC30 W25 . Example) 1. Porti-S40 / Serial/Bluetooth Wireless A RS-232C 1 Bluetooth B TTL 2 IrDA C USB 0 None D RS-485 E Parallel Z None Part No. ⇒ S40/A1 Bluetooth Only Part No. ⇒ SC30/Z1 http://www.woosim.
1.3. Specifications. Item Specifications Print method Direct thermal line printing Characters per line 64cpl (MAX) Character size Eng. : 9× 24dots, 12× 24dots Optional Characters Kor. : 16× 24dots, [24× 24dots] Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek, Japanese, Persian, Latin9 and Others upon request. Resolution 203dpi, 8dots/mm Print width 3-inch (72mm, 576dots) Print speed 60mm / sec (MAX) Dimension 120× 130.5× 58.
2. Setting up the printer. 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Battery Pack Paper Roll WSP-i350 Battery Charger ▼ OPTIONAL Communication Cable Shoulder band http://www.woosim.
2.2. Printer Features ▶ Part Name http://www.woosim.
▶ Dimensions http://www.woosim.
2.3. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover by placing your fingers under the paper cover lock and pull a paper cover lock open. 3. Insert a new paper roll as shown. 4.
2.4. Power supply 2.4.1. Specified power supply. The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the battery and the belt strap NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer.
2.4.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases. (Warranty 6 month) ● If the printer is not used for a long time, unplug the power cord from the printer and outlet.
2.5. Set operation mode. 1. Change the mode and option using the mode Code (Table1). z POWER button : changing Printer MODE status. z FEED button : changing OPTION status. 2.
X Press FEED button one time. → You will see present STOP BIT mode in the LCD. → Press POWER Button one time. (The stop bit has set to 2 stop bit.) X Press FEED button one time. → You will see present DENSITY mode in the LCD. → Press POWER Button two times. (The density has set to high.) If all the mode have set, press the FEED Button and the POWER Button at the same time after then release the buttons at the same time. The printer will print out the mode status which has modified.
Communication Port POWER Lamp ERROR Lamp (Green) (Red) 1 Option 1 UART 2 Protocol UART 3 Raw IrDA ( Bluetooth / WLAN) Protocol IrDA 4 ( Protocol Bluetooth / Protocol WLAN) Baud Rate Data Bit Parity Bit Stop Bit Density Quality 2 3 4 5 6 7 1 9600 bps 2 19200 bps 3 38400 bps 4 57600 bps 5 115200 bps 1 7 Data bit 2 8 Data bit 1 No Parity 2 Even Parity 3 Odd Parity 1 1 Stop bit 2 2 Stop bit 1 Density Low 2 Density Medium 3 Density High 1 Low 2 High ht
Mark Sensor Power Down POWER Lamp ERROR Lamp (Green) (Red) 8 9 10 Option 1 No use 2 Use 1 Low 2 Medium1 3 Medium2 4 High 1 No use 2 1 minute 3 2 minute 4 3 minute 5 4 minute 6 5 minute http://www.woosim.
3. Interface. 3.1. UART(RS-232C or TTL) The WSP-i350 printer has a RS-232C or TTL interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the MiniUSB socket are listed: NOTE : ● Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 CTS - - 4 NC. - - 5 GND - Ground When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.
3.2. Infrared data communication The WSP-i350 has a serial interface for bi-directional data exchange. The infrared port is the right side of the front part. 1. To use the WSP-i350’s infrared port by a Computer or a Personal Digital Assistant (PDA) with IR port is required. 2. Position a PDA conforming to the specifications in point not more than 50 centimeter away from the printer’s infrared port. Make sure the two ports are in front of each other with an angle of not more than 15° on the four sides.
3.3. Bluetooth Category Specification Bluetooth Spec. Bluetooth V2.0/ Class2 (10m) Frequency Range 2.4GHz ISM BAND Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. Notice If the quantity of data which is printed at once is more than 10K byte on Bluetooth communication, it would cause the buffer to overflow and the data to get damaged. 3.4.
Infrastrcture mode Ad-hoc Mode http://www.woosim.
3.4.1 wLAN SETTING 1. wLAN Manager Program summary wLAN Manager is a utility program, which configures i-350 equipment settings wireless LAN. 2. wLAN Manager program function 2.1. The selection of the wLAN Manager Program operating mode You can select wLAN Manager program operating mode using [LOCAL] or [REMOTE] and Serial. Following is the screen shot of WSwLAN_Manager which is just launched. http://www.woosim.
2.2. Select Serial from the MenuÆConnection (default : Serial) 1) Click “Open” button after serial communication config. 2) Click “Get Info” button. 3) Complete setting and click “Set Info” button. http://www.woosim.
2.3. Select TCP/IP from the MenuÆConnection 1) Local Mode ① Remove serial cable in printer ② Click “Search” button ③ Click Searched MAC Address. ④ Complete setting and click “Set Info” button. http://www.woosim.
2) Remote Mode ① Remove serial cable in printer. ② Select “Remote” mode and Input after confirm allocated IP Address in printer LCD. ③ Complete setting and click “Set Info” Button. http://www.woosim.
2.4. Setup Item 1) TCP / IP Group TCP / IP Peer Address IP address or host name to connect in TCP Client mode IP address or host name to send in U2S mode Peer Port Port number to connect in Client mode Local Port Port number for waiting to be connected in T2S Client mode. Port number for UDP data in U2S mode.
2) Network Group Network Local IP Address Subnet Mask Gateway IP address DHCP Obtion DNS server address automatically User Class ID i350 IP address Subnet Mask Gateway’s IP address Decide whether to receive i350 IP address via DHCP If i350 IP address is set a dynamic IP(DHCP), it will automatically receive DNS server address. If this check box is not activated, the IP address designated in the [DNS IP Address] will be used as the DNS server address.
3) WLAN Basic Config Group WLAN Basic config WLAN Mode SSID Channel Network type to connect. ( Infrastructure / Ad-hoc ) SSID to connect (Maximum 32 bytes) Default value : woosim Channel number for ad-hoc (The channel number will be random in some case.) 4) WLAN Security Group ① None. ② WEP. XNote - WEP-64bit : Max key length is 5 byte, and store up to 4 keys. - WEP-128bit : Max key length is 13 byte, and store up to 4 keys. http://www.woosim.
③ WPA. X Note - WPA-PSK : Input more than minimum 8 byte. 2.5. Setting WEP key. Check the settings of AP to connect to (authenticate method – open, shared key; key length – 64 bits, 128 bits and key index). 1) Click the [WEP] menu 2) Select an Authentication method – [Open System] / [Shared Key] 3) Select a WEP key length – [64 Bits] / [128 bits] 4) Select a key index to use – [Key1] / [Key2] / [Key3] / [Key4] 5) Select key format to input – [HEX] / [ASCII] 6) Input the Key.
4. Using the printer. 4.1. Control panel. X Button - FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button : ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions. MODE functions are for use to change communication mode. (Refer to 2.5.
4.2. The self test. The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set.
5. Consumable Parts. 5.1. Recommended paper. Type : Thermal Paper Paper width : 80mm Paper thickness : 60±5㎛ Outer diameter : Ø50mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃. Pay attention to heat, humidity and sun light. 4.
FCC ID : QDDWSP-I350 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition. http://www.woosim.
