MODEL PORTI-WC40 (4inch Mobile Printer) WOOSIM SYSTEMS Inc. Add : #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
Copyright PORTI-WC40 portable mobile printer operator’s manual. Copyright ⓒ2009 by Woosim System Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
Introduction The PORTI-WC40 is suitable designed for use with a growing variety of mobile devices Bluetooth/Serial interfaces make the PORTI-WC40 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of PORTI-WC40 printer are as follows: X Pocket size (138.4mm x 88.5mm x 45.7mm). X Light weight(314g without paper) for true mobility. X Very silent printing thru direct thermal printing method.
Operating Precaution Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
X Thermal Paper Handling ● Store the thermal paper in a cool, dry and dark place. ● Do not rub the paper with hard object. ● Do not leave the paper with hard object. ● Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. ● Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. ● Do not use chemical glue. ● Always use the clean thermal paper. http://www.woosim.
CONTENTS Copyright .............................................................................................................................2 Trademark ............................................................................................................................2 Caution.................................................................................................................................2 1. Outline .................................................................................
1. Outline 1.1. Model classifications PORTI-WC40 ( ) ( ) Model Name Interface None : Bluetooth/UART Power None : DC 8.4V 1.2. Product Part Number System Model name / Interface Spec. Wired S40 SC30 W25 . . . Example) 1. Porti-S40 2. Porti-SC30 Wireless A UART 1 Bluetooth B TTL 2 IrDA C USB 0 None D RS-485 E Parallel Z None UART/Bluetooth Part No. ⇒ S40/A1 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported.
1.3. Specifications Item Specification Printing method Direct thermal line printing Characters per line 92cpl Character size Eng. : 9*24dots, 12*24dots Kor. : 16*24dots, [24*24dots] Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek, Optional Characters Japanese, Persian, Latin9 and Others upon request. Resolution 203dpi, 8dots/mm Print width 4-inch (104mm, 832dots) Printing speed 50mm /sec Dimensions 138.4*88.5*45.
2. Setting up the printer 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Battery Pack Roll Paper PORTI-SWC40 Battery Charger ▼ OPTIONAL Extra Charger Communication Cable http://www.woosim.
2.2. Printer Features 2.2.1. Part name http://www.woosim.
2.2.2. Dimensions http://www.woosim.
2.3. Replacing paper roll Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover using finger on both side of printer, and remove the remaining paper. 3. Insert the paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.
2.4. Power supply 2.4.1. Internal power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the Battery NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer. CAUTION : Risk of explosion if battery is replaced by an incorrect type.
2.4.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer or the extra charger. Insert the Battery Charger to the charge connector of the printer or the extra charger. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
2.5. Set operation mode 1. Press the MODE Button until the Error Lamp twinkles 5 times. 2. Change the mode and option using the MODE Button according to the MODE (Table1). z MODE button : use for changing OPTION status. (Error Lamp) z FEED button : use for changing MODE status.
X Press FEED Button two time, Power Lamp twinkles six times and Error Lamp twinkles once. → Press MODE Button one time, Error Lamp twinkles twice after then press MODE Button again, the Error Lamp will twinkle three times. ( The Density has set to High) If all the mode have set, press the MODE Button and the FEED Button at the same time after then release the buttons at the same time. The printer will print out the mode status which has modified.
Communication Port Baud Rate Data Bit Parity Bit Stop Bit Density Mark Sensor POWER Lamp ERROR Lamp (Green) (Red) 1 2 3 4 5 6 7 8 Option 1 UART 2 Protocol UART 3 Bluetooth 4 Protocol Bluetooth 1 9600 bps 2 19200 bps 3 38400 bps 4 57600 bps 5 115200 bps 1 7 Data bit 2 8 Data bit 1 No Parity 2 Odd Parity 3 Even Parity 1 1 Stop bit 2 2 Stop bit 1 Density Low 2 Density Medium 3 Density High 1 No use 2 Use 1 Low 2 Medium1 3 Medium2 4 High htt
Power Down POWER Lamp ERROR Lamp (Green) (Red) 9 Option 1 No use 2 1 minute 3 2 minute 4 3 minute 5 4 minute 6 5 minute http://www.woosim.
3. Interface 3.1. UART(RS-232C or TTL) The PORTI-WC40 printer has an UART interface and is connected by means of a 4 pin mini USB socket. In the following table, the signals present on the Mini USB socket are listed: Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 CTS - - 4 GND - Ground * Applicable connector : SUNG KYUNG (CM-720) NOTE : ● When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.
3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth V2.1 / Class2 (10m) Frequency Range 2.4GHz ISM BAND(2.402~2.480MHz) Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. 3.2.
4. Using the printer 4.1. Control panel X Button - FEED : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - MODE : MODE Button is for use to change communication mode. Do not operate the mode button without instructions. X Panel lamp - Power : Printer is ON and ready to receive data. - Error : Indicates a fault condition or a printer error. (i.e : no paper, paper cover opened. etc.
4.2. Self test The Self-Test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. For Self-Test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting.
5. Consumable parts 5.1. Recommended paper Type : Thermal Paper Paper width : 113mm Paper thickness : 60±5㎛ Outer diameter : Ø38mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core, and the roll paper which has near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70 ℃. Pay attention to heat, humidity and sun light. 4.
FCC ID : QDDPORTI-WC40 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition. http://www.woosim.