MODEL PORTI-SW40 WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
Copyright PORTI-SW40 portable printer operator’s manual. Copyright གྷ2007 by Woosim System Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity.
Introduction The PORTI-SW40 is suitable designed for use with a growing variety of mobile devices. IrDA/Serial or Bluetooth/Serial interfaces make the PORTI-SW40 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of PORTI-SW40 printer are as follows: X Pocket size (107.5mm x 88.5mm x 45mm). X Light weight(360g) for true mobility. X Very silent printing thru direct thermal printing method.
Operating Precaution Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer Ɣ Be careful not to drop or bump the printer on a hard surface. Ɣ Do not install the printer in direct sunlight or such areas.
X Thermal Paper Handling Ɣ Store the thermal paper in a cool, dry and dark place. Ɣ Do not rub the paper with hard object. Ɣ Do not leave the paper with hard object. Ɣ Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. Ɣ Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. Ɣ Do not use chemical glue. Ɣ Always use the clean thermal paper.
CONTENTS 1. Outline ............................................................................................................................................7G 1.1. Model classifications ............................................................................................................7G 1.2. Product Part Number System................................................................................................7G 1.3. Specifications..............................................................
1. Outline 1.1. Model classifications ( PORTI-SW40 ) ( ) Model Name Interface None : IrDA/Serial BT : Bluetooth/Serial Power None : DC 8.4V 1.2. Product Part Number System Model name 2. Porti-SC30 Interface Spec. Wired S40 SC30 W25 . . . Example) 1. Porti-S40 / Serial/Bluetooth Wireless A RS-232C 1 Bluetooth B TTL 2 IrDA C USB 3 HPIR D RS-485 0 None E Parallel Z None Part No. ൽ S40/A1 Bluetooth Only Part No. ൽG SC30/Z1 http://www.woosim.
1.3. Specifications Item Specification Printing method Direct thermal line printing Characters per line 64cpl Character size Eng. : 9*24dots, 12*24dots Resolution 203dpi, 8dots/mm Print width 3-inch (72mm, 576dots) Printing speed 40mm / sec Dimensions 107.5 * 88.5 * 45 mm Weight 360g Interface RS-232C or TTL / Bluetooth Paper supplied Thermal roll paper (80mm wide, 38ø) Barcode supplied Receive buffer size Note Kor.
2. Setting up the printer 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Battery Pack Roll Paper PORTI-SW40 Battery Charger ̷G OPTIONAL Extra Charger Communication Cable http://www.woosim.
2.2. Printer Features 2.2.1. Part name 2.2.2. Dimensions http://www.woosim.
2.3. Replacing paper roll Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover using finger on both side of printer, and remove the remaining paper. 3. Insert the paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.
2.4. Power supply 2.4.1. Internal power supply The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the Battery G NOTE : Ɣ Before installing or removing the battery pack, ensure the printer is G OFF. G Ɣ If the printer is not used for long period of time, remove the battery G pack from the printer.
2.4.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer or the extra charger. Insert the Battery Charger to the charge connector of the printer or the extra charger. ٻ ٻ NOTE : Ɣ While charging the printer, turn off the printer power. Ɣ Do not remove the battery during charging. Ɣ The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
2.5. Set operation mode 1. Press the MODE Button until the Error Lamp twinkles 5 times. 2. Change the mode and option using the MODE Button according to the MODE (Table1). z MODE button : use for changing OPTION status. (Error Lamp) z FEED button : use for changing MODE status.
X Press FEED Button one time, Power Lamp twinkles 3 times and Error Lamp twinkles 2 times. o Press MODE Button one time, Error Lamp twinkles one time. (The Data Bit has set to 7 data bit) X Press FEED Button one time, Power Lamp twinkles 4 times and Error Lamp twinkles 1 time. o Press MODE Button one time, Error Lamp twinkles 2 times. (The Parity bit has set to even parity bit) X Press FEED Button one time, Power Lamp twinkles 5 times and Error Lamp twinkles 1 time.
tvklG Communication Port Baud Rate Data Bit Parity Bit Density POWER Lamp ERROR Lamp (Green) (Red) 1 2 3 4 5 Protocol 6 Mark 7 Option 1 RS-232C 2 Protocol IrDA / Protocol Bluetooth 3 Standard IrDA / Bluetooth 1 1200 bps 2 2400 bps 3 4800 bps 4 9600 bps 5 19200 bps 6 38400 bps 7 57600 bps 8 9600 bps 1 7 Data bit 2 8 Data bit 1 No Parity 2 Even Parity 3 Odd Parity 1 Density Low 2 Density Medium 3 Density High 1 Default Protocol 2 Lotte Protocol 1
3. Interface 3.1. RS-232C The PORTI-SW40 printer has a RS-232C interface and is connected by means of a 4 pin mini USB socket. In the following table, the signals present on the Mini USB socket are listed: Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 CTX - - 4 GND - Ground * Applicable connector : SUNG KYUNG (CM-720) NOTE : Ɣ When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.
3.2. Infrared data communication The PORTI-SW40 has a serial interface for bi-directional data exchange. The infrared port is the right side of the front part. 1. To use the PORTI-SW40’s infrared port by a Computer or a Personal Digital Assistant (PDA) with IR port is required. 2. Position a PDA conforming to the specifications in point not more than 50 centimeter away from the printer’s infrared port. Make sure the two ports are in front of each other with an angle of not more than 15° on the four sides.
3.3. Bluetooth 3.3.1. Bluetooth Spec. Category Specification Bluetooth Spec. Bluetooth V1.1 / Class2 (10m) Frequency Range 2.4GHz ISM BAND Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. Notice If the quantity of data what printed at once is more than 20K byte on Bluetooth communication, it would cause the buffer to overflow and the data to get damaged. 3.3.2.
4. Using the printer 4.1. Control panel X Button - MODE Button MODE Button is for use to change communication mode. (Refer to 2.5. ADJUSTMENT AND SETTING for details about mode conversion) If you want to set to RS-232C Mode, just connect the communication cable to connector of the printer and then the mode will be changed automatically. - FEED Button Press the FEED Button once to advance paper one line. You can also hold down the FEED Button to feed paper continuously.
4.2. Self test The Self-Test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. For Self-Test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting.
4.3. Driver installation The driver installation instruction were written for the printer to be used with the Infrared port and serial port(RS-232C). Make sure that your PC has built-in infrared device(IrDA Ver1.0). Printer driver can download by Internet(http://www.woosim.com). Installing the PORTI-W Printer Driver on Windows 98/ME/2000/XP. 1) You must install new driver after deleting old driver.
3) Select printer model to install, and press “Next”. (Fig.4.3.2) 4) Select the port connected to printer, and press “Next” (Fig.4.3.3) http://www.woosim.
5) If the installation has done successfully, press “OK”. (Fig.4.3.4) 4.4. Bit-image download The PORTI-SW40 Printer supports bit image download to the internal Flash ROM. The bit image download require the Porti_Download application and PCX file. - Porti_Download Application : The Porti_Download application can download by internet( http://www.woosim.com). - PCX file : The picture must be black or white PCX file and the width of picture must be x8 pixel.
4. 5. Troubleshooting Check the following points before you make a request for repair. X The power does not turn on. ● AC adapter or battery pack being used? ● AC cable and AC adapter or batter pack is connected. ● AC adapter is connected to the printer correctly? ● Battery pack is fully recharged? X The printer does not print.
X Error Lamp of the power Lamp is blinks. ● Paper end or cover open ? ● Battery is almost exhausted? (Recharge the battery by using the power supply.) X The battery pack is not installed. ● Battery pack correctly oriented? ● Correct battery pack being used? ● Battery pack case damaged? X The battery runs out soon even if recharged. ● Battery been recharged correctly? ● If the battery is recharged correctly, but does not take a long time, it is almost dead. Replace if with a new one. http://www.woosim.
5. Consumble parts 5.1. Recommended paper Type : Thermal Paper Paper width : 113mm Paper thickness : 70±5 Mm Outer diameter : Ø38mm or less Recording side : Outside of roll Cautions : 1. Do not paste the paper to the core, and the roll paper which has near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70 C. Pay attention to heat, humidity and sun light. 4.