MODEL PORTI-SM40 (Mobile Printer) WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com http://www.woosim.
Copyright Porti-SM40 Mobile printer operator’s manual. Copyright ⓒ2008 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity.
Introduction The Porti-SM40 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of Porti-SM40 printer are as follows: X Pocket size(80.5×113.
Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
CONTENTS Copyright .....................................................................................................................................2 Trademark ....................................................................................................................................2 Caution.........................................................................................................................................2 Operating Precautions ..............................................
. Consumable Parts. .......................................................................................................................25 6.1. Recommended paper. ..............................................................................................................25 6.2. Printing position......................................................................................................................25 http://www.woosim.
1. Outline. 1.1. Model classifications. ( PORTI–SM40 ) ( ) Model Interface None: UART/Bluetooth Power None : DC 8.4V 1.2. Product Part Number System. Model name S40 SC30 W25 . . . / Interface Spec. Wired Wireless A RS-232C 1 Bluetooth B TTL 2 IrDA C USB 0 None D RS-485 E Parallel Z None Example) 1. Porti-S40 Serial/Bluetooth Part No. ⇒ S40/A1 2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported.
1.3. Specifications. Item Specifications Print method Direct thermal line printing Characters per line 42cpl (MAX) Character size Eng. : 9×24dots, 12×24dots Kor. : 16×24dots, [24×24dots] Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek, Optional Characters Japanese, Persian, Latin9 and Others upon request. Resolution 203dpi, 8dots/mm Print width 2-inch (48mm, 384dots) Print speed 80mm / sec (MAX) Dimension 80.5×113.
Item Environment conditions MCBF(Mean Cycle Between Failure) Specifications Temperature -20°C ~ 55°C (operating) Humidity 0% - 95% (operating) Mechanical Head 37,000,000 lines Approximately 50 Km http://www.woosim.
2. Setting up the printer. 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Battery Pack Paper Roll PORTI-SM40 Battery Charger ▼ OPTIONAL Extra Charger Communication Cable http://www.woosim.
2.2. Printer Features ▶ Part Name http://www.woosim.
▶ Dimensions http://www.woosim.
2.3. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover by placing your fingers under the paper cover lock and pull a paper cover lock open. 3. Insert a new paper roll as shown. 4.
2.4. Power supply 2.4.1. Specified power supply. The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the battery NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer. CAUTION : Risk of explosion if battery is replaced by an incorrect type.
2.4.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer or the extra charger. Insert the Battery Charger to the charge connector of the printer or the extra charger. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
2.5. Set operation mode. 1. Change the mode and option using the mode Code (Table1). z MODE button : changing Printer MODE status. z FEED button : changing OPTION status. 2. [Example] The defaults of the printer are : UART/ 9600 BPS/8 DATA BIT/ NO Parity/1 STOP BIT/ Density LOW If a user wants to modify the defaults with Bluetooth/38400 BPS/7 DATA BIT/Even Parity/2 STOP BIT/Density HIGH X Press MODE Button until Error Lamp twinkles 5 times. → You will see present COMMUNICATION mode in the LCD.
X Press FEED button one time. → You will see present STOP BIT mode in the LCD. → Press MODE Button one time. (The stop bit has set to 2 stop bit.) X Press FEED button one time. → You will see present DENSITY mode in the LCD. → Press MODE Button two times. (The density has set to high.) If all the mode have set, press the FEED Button and the MODE Button at the same time after then release the buttons at the same time. The printer will print out the mode status which has modified.
Mode No. 1 2 3 4 5 6 7 8 Printer Mode Option Option No.
3. Interface. 3.1. UART(RS-232C or TTL) The Porti-SM40 printer has a RS-232C or TTL interface and is connected by means of a 4 pin mini USB socket. In the following table, the signals present on the MiniUSB socket are listed: Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 CTS - 4 GND - Ground * Applicable connector : SUNG KYUNG (CM-720) NOTE : ● When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.
3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth V2.1 / Class2 (10m) Frequency Range 2.4GHz ISM BAND (2.402~2.480GHz) Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. 3.2.
4. Smart Card Module 4.1. General Spec. X Contact Smart Card Reader Module for ISO/IEC-7816 X Support Asynchronous Protocol T=0,T=1 X Smart Card Connection - Short Circuit Current Limitation - 6KV ESD Protection on whole Smart Card Interface - Connector : Friction Type with Smart Card presence detection X 2 SAM (Security Application Module) X EMV Level 1 Certified http://www.woosim.
4.2. Communication Protocol Sequence 4.2.1. Regular Operation Host Command Module Execution Response 4.2.2. Irregular Operation (Communication Error) 500ms timeout Host Command Command Module Host Command Command is Command Executio Command Error Module CheckSumEr http://www.woosim.
5. Using the printer. 5.1. Control panel. X Button - FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - MODE Button : MODE Button is for use to change communication mode. (Refer to 2.5. Set operation mode for details about mode conversion) X Panel lamp -POWER (Green) : Printer is ON and ready to receive data. -ERROR (Red) : Indicated a fault condition or a printer error. (i.e : no paper, paper cover opened. etc.
5.2. The self test. The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set.
6. Consumable Parts. 6.1. Recommended paper. Type : Thermal Paper Paper width : 57mm Paper thickness : 60±5㎛ Outer diameter : Ø40mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃. Pay attention to heat, humidity and sun light. 4.
FCC ID : QDDPORTI-SM40-ABC THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition. http://www.woosim.