MODEL PORTI-SB50 (Mobile Printer) WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com All specifications are subjected to change without notice http://www.woosim.
FCC Compliance Statements Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Copyright PORTI-SB50 mobile printer operator’s manual. Copyright ཱྀ2006 by Woosim System Inc. All rights reserved. The information contained in this manual is the property of Woosim System Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim System Inc. Trademark a registered trademark of Woosim System Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity.
Introduction The PORTI-SB50 is suitable designed for use with a growing variety of mobile devices. RS232, IrDA(physical layer) and HPIR interfaces make the PORTI-SB50 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of PORTI-SB50 printer are as follows: X Pocket size (78mm x 131.5mm x 55mm). X Light weight(200g) for true mobility. X Very silent printing thru direct thermal printing method.
Operating Precaution Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer Ɣ Be careful not to drop or bump the printer on a hard surface. Ɣ Do not install the printer in direct sunlight or such areas.
X Thermal Paper Handling Ɣ Store the thermal paper in a cool, dry and dark place. Ɣ Do not rub the paper with hard object. Ɣ Do not leave the paper with hard object. Ɣ Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. Ɣ Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. Ɣ Do not use chemical glue. Ɣ Always use the clean thermal paper. http://www.woosim.
CONTENTS 1. Outline ..............................................................................................................................7G 1.1. Model classifications ...............................................................................................7G 1.2. Specifications ..........................................................................................................8G 2. Setting up the printer ...................................................................................
1. Outline 1.1. Model classifications PORTI-SB50 ( ) ( ) 㩷 Model Name Interface None : RS-232C IrDA / HPIR Power None : Dry Cell (AA size, 4EA) http://www.woosim.
1.2. Specifications Item Specification Print method Direct thermal line printing Characters per line 48cpl (MAX) Character size Eng. : 8×24dots , 9×24dots, 12×24dots, 16×24dots Resolution 203dpi, 8dots/mm Print width 2-inch (48mm, 384dots) Print speed 50mm / sec (MAX) Dimension 78 × 131.
2. Setting up the printer 2.1. Printer & Accessories When unpacking your printer box make sure it contains the printer and all accessories. If any accessories are missing or damage, please contact your dealer for assistance. ROLL PAPER PORTI-SB50 http://www.woosim.
2.2. Printer Features 2.2.1. Part name 2.2.2. Dimension http://www.woosim.
2.3. Replacing paper roll Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover using finger on both side of printer, and remove the remaining paper. 3. Insert a new paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.
2.4. Power supply 2.4.1. Internal power supply ̲ The following specification is requested for Power supply. Power supply : 4 X 1.2V Ni-MH 1600mAh, AA cells (Battery Charging : 9VDC/800mA) ̲ Use only power supplies stipulated specifically for your PORTI-SB50 printer. Using a different power supply may cause damage to the printer. 2.4.2. Installing the Battery GNOTE : ̻ G Before installing or removing the dry cells, ensure the printer is OFF.
2.4.3. Recharging the battery Before recharging the battery, install the battery in the printer. Insert the charger to the charge connector of the printer, as shown. ٻ ٻ NOTE : Ɣ While charging the printer, turn off the printer power. Ɣ Do not remove the battery during charging. Ɣ The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases. (Warranty 6 month) Ɣ If the printer is not used for a long time, unplug the power cord from the printer and outlet.
3. Interface 3.1. RS-232C The RJ-12 socket is provided for applications requiring RS-232C interface with connections as detailed below: Pin No. Signal I/O Definition 1 GND N/A Signal Ground 2 TxD O Transmitted data to host 3 RxD I Received data from host 4 N/C N/A No connection 5 N/C N/A No connection 6 N/C N/A No connection NOTE : Ɣ When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.
3.2. Infrared data communication The PORTI-SB50 has a serial interface for bi-directional data exchange. The infrared port is the left side of the front part. 1. To use the PORTI-SB50’s infrared port by a Computer or a Personal Digital Assistant (PDA) with IR port is required. 2. Position a PDA conforming to the specifications in point not more than 50 centimeter away from the printer’s infrared port. Make sure the two ports are in front of each other with an angle of not more than 15° on the four sides.
4. Using the printer 4.1. Control panel X Button - FEED : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - MODE : MODE Button is for use to change communication mode. Do not operate the mode button without instructions. X Panel lamp - Power : Printer is ON and ready to receive data. (Green) The status indicator will flash continuously to show the batteries are nearly exhausted and in need of re-charging.
4.2. Self test The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set.
4.3. Troubleshooting Check the following points before you make a request for repair. X The power does not turn on. ഘ Charger or dry cell(AA size, 4EA) being used? ഘ AC cable and Charger or dry cell is connected. ഘ Charger is connected to the printer correctly? ഘ Dry cell is fully recharged? X The printer does not print.
X Error Lamp of the power Lamp is blinks. ഘ Paper end or cover opened? ഘ Battery is almost exhausted? (Recharge the battery by using the AC adapter.) X The Dry cell is not installed. ഘ Dry cells correctly oriented? ഘ Correct dry cells being used? X The battery runs out soon even if recharged. ഘ Battery been recharged correctly? ഘ If the battery is recharged correctly, but does not take a long time, it is almost dead. Replace if with a new one. http://www.woosim.
5. Consumable parts 5.1. Recommended paper Type : Thermal Paper Paper width ٻPaper thickness : 57mm : 70±5༁ Outer diameter : Ø50 or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed characters may fade. 3. Change of paper color starts from approx. 70 ఁ. Pay attention to heat, humidity and sun light. 4.