WONGKUO V2.
Introduction to the Product Contents Englisches —————————————— 1-27 WONGKUO Battery Camera is a high-definition security device specially designed for home users. It not only has the function of ordinary security devices to view the monitoring content online at any time, but also integrates many features such as visitor voice intercom, short video recording, remote active wake-up, real-time online multiplayer viewing, ultra-low power consumption, etc., to effectively protect your home..
Light Meaning List of Solar Version WONGKUO WONGKUO Battery Camera Stand Rechargeable 6000mAh Battery Pack Solar Panel + Mounting arm Anchor Packs Screw Packs User Manual Micro USB Part Characteristics 1. Microphone 2. Wide-angle lens 3. Indicator light 4. PIR motion sensor 5. Photosensitive sensor 6.
3. Both the red and blue lights on the top of the battery pack will be constant on while charging. When it is fully charged, the red light goes out and the blue light stays on, and the battery pack automatically enters the state of protection to accidents caused by overcharging; the first charge takes 6-8 hours. Set up the Battery Camera 1. Remove the battery cover.
3. Match the battery camera in the AiWit APP WONGKUO Battery Camera will start automatically and enter the network matching mode with a voice prompt when the fully charged battery pack is correctly installed and the insulation sticker is removed; to match the battery camera, follow steps (1) Open the Aiwit App on your mobile phone and log into the previously registered email account. (5) Go to your 2.
(7) Aim the lens of WONGKUO Battery Camera at the QR code displayed on the mobile phone APP, keep the lens about 0.33ft away from the phone’s screen, and don’t take it away until you hear the prompt tone of successful scanning; wait until the Wi-Fi installation is completed and select “OK” when you hear the tone of successful matching. At the same time, all matches have been completed.
4. Aim the camera bracket at the base of the bracket, rotate the threaded rubber cap on the bracket clockwise to fix the device on the base, adjust the lens angle of WongKuo Battery Camera, and tighten the threaded rubber cap. 2 1 3 4 5 5. If the lens control surface of WongKuo Battery Camera is found to be skewed after installation, loosen the rubber cap and readjust the angle until the angle is satisfied, then tighten the rubber cap again to fix it. Introduction to the Functional Interface 1.
(3) Battery Indicator icon (7) Device Sharing It is displayed in gray on the homepage; it will turn green on the real-time monitoring screen when charging, with an icon after unplugging the power cord, it will be displayed in white, and it will turn red when the power is short, and there will be an email reminder of power shortage.
(3) Resolution 2. Introduction of live video interface 1 2 It is the resolution of the video. The default resolution of Wongkuo Battery Camera is 1080P. 3 4 (4) Battery pack battery indicator 5 6 7 8 9 10 12 11 It turns green when charging with an icon; after unplugging the power cord, it will be displayed in white; and it will turn red when the power is short. Next to it, the number of remaining power will be displayed in percentage, and there will be an email reminder of power shortage.
(9) External sound play Click on the speaker to turn on/off the sound from your WongKuo Battery Camera. By default, it is off. Please turn on the speaker when using the intercom function or when you want to hear external sound. 3. Details of Device Sharing (10) Video playback Click to enter the page of Historical Events, view and playback videos recorded during PIR monitoring and real-time monitoring (same as the function button of “Historical Events” on the homepage.
4. Details of Detection Sensitivity (2) Sharing via QR Code There are two ways to share via QR code 1. When the master account and the sub-account are together, the sub-account opens the sharing page on the APP and selects the scan function. The master account clicks to open Sharing via QR Code on the sharing page. At this time, a QR code picture will appear on the mobile phone of the master account.
5. Details of Playback (4) List of video files recorded during PIR motion detection 1 12 Click here and only the videos recorded during PIR detection are displayed below. Each video is 15 seconds long. (5) List of video files recorded during real-time monitoring 11 2 10 3 9 4 5 8 Click here and only the videos recorded during real-time monitoring are displayed below. The duration is subject to what you record, but it is no more than 3 minutes.
(11) Play/Pause 2. How to reset network settings? Click to control the play and pause of the current playback video. (12) Return touch button Click here to return to the homepage directly from the playback function page. Help In case of any problems during the application installation process, try the following steps: 1. Check your WiFi password The most common problem during installation is an incorrect Wi-Fi password. The password is case sensitive. Please check your password carefully.
4. How many users can watch the video at the same time? Up to three users can watch live video, but only one user can use direct intercom. Both iOS and Android are compatible. 5. Does it support 5GHz WiFi network? No. WONGKUO Battery Camera only supports 2.4GHz WiFi network. 6. Why is the WiFi signal on my device so bad? Help Your device may be too far away from the wireless router, or there may be some obstacles between your device and the router, which will reduce the signal strength.
3. Drill You can use an electric drill to make holes at the location you marked earlier. For brick, concrete or plaster surfaces, plastic anchors must be used. Please use a hammer to install the anchor in place. Note: You can adjust the angle of the solar panel for better sunlight coverage. Simply loosen the adjusting screw on the mounting arm, adjust it to the desired angle, and then tighten the screw again.