*** USER’S MANUAL *** FCC ID : SRKWPBT77X
The Federal Communication Commission Statement This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication.
Bluetooth GPS Receiver Contents 1. INTRODUCTION..........................................................................................................................1 1.1. OVERVIEW ...............................................................................................................................1 1.2. MAIN FEATURES.......................................................................................................................1 2. TECHNICAL SPECIFICATIONS ..............................
1. Introduction 1.1. Overview The BT-77 Bluetooth GPS receiver is a Global Position System Receiver with Bluetooth wireless technology. This BT GPS receiver allows you to receive GPS data on mobile handhelds wirelessly. By sending GPS position data over Bluetooth, you can position the receiver for the best possible reception all without wires. The advent of Bluetooth GPS receiver will become the next level of GPS receivers. The BT GPS receiver integrates Bluetooth module into GPS device.
2.TECHNICAL SPECIFICATIONS General GPS technology NEMERIX GPS module Frequency L1, 1575.42 MHz C/A code 1.023 MHz chip rate Channels 16 channels all in view tracking Antenna (internal) Built-in low noise External Antenna Port active MMCX antenna Sensitivity to -147 dBm tracking, superior urban canyon performance Accuracy Position 3 meters CEP (50%), without SA (horizontal) 7 meters (90%) 0.
3.2. What do you get in the box? 9 BT GPS receiver 9 A Adapter , 5.3V/500mA output 9 A user’s manual ( CD disc ) 9 A Li-Polymer rechargeable battery 850mAh 3.3.1 Software Install - Pocket PC CE iPAQ Bluetooth fuction setup with Pocket PC software On the client, make sure the Bluetooth device is available. <1> Tap Bluetooth pop-up menu, Turn Bluetooth ON and select Bluetooth manager. <2> Established new connection , click .
<7> Select “SPP slave “ , click “Next” Ш“Finish “ And BT-GPS connection Established successfully. <9> Tap “ Bluetooth icon “ again , and select “ Bluetooth setting “. 3.3.2 Software setup – Navigator (PaPaGo! 5) <9> Tap “ Serial port “ , Enable service first , then , set up outbound COM port to be “8”.
<1.> Find Navigator software in programs , and tap PaPaGo! 5 Navigator <2.> Tap “tools” and select “setup”. The Navigator of map is Chinese version ,and shows as follow. The English version should be similar with Chinese. <3.> Tap “GPS” table , as following setup. <4.> Return to PaPaGo main screen . tap “tools” and select “GPS” Ш “ GPS position “ <5.> GPS position fixed ans start navigating.
Appendix A Test Reference for Only PC Bluetooth Setup with Widcomm BTW This software does belong to copyright reserved of Widcomm company and you have to get the authorized software to use it. The follow method is only for reference. The Bluetooth Serial Port service allows two Bluetooth devices to establish a wireless connection through virtual communications ports and then use that connection as if it were a hardwired serial cable between the devices.
<2> In the right pane of Entire Bluetooth Neighborhood, right-click anywhere except on a device name and select Refresh from the pop-up menu. <3> In the Folders pane of My Bluetooth Places, right-click the server you want to establish a connection with and select Discover Available Services from the popup menu to update the available services list. The available services will be displayed in the right pane of My Bluetooth Places.
<4> In the right pane of My Bluetooth Places, double-click Bluetooth Serial Port. A dialog box appears that contains the communications port number assigned to this connection by the client. The application that will use this connection must be configured to send data to this port.
To close a Bluetooth serial port connection , Connections are normally closed from the client: .. On the client, in the Folders pane of My Bluetooth Places, select (highlight) the device that is providing the Bluetooth Serial Port service. .. In the right pane of My Bluetooth Places, right-click Bluetooth Serial Port and then select Disconnect Bluetooth Serial Port from the pop-up menu.
