Wolverine 35mm Film to Digital Converter Model F2D USER MANUAL Version 1.
TABLE OF CONTENTS DESCRIPTION PAGE Table of Contents 1 Before Using the F2D Converter 3 FCC Certifications 3 Warning 4 Help Phone Line 6 Features 6 Fast Track Guide 8 ~ 14 1. Clean Converter Camera 8 2. Attach Power 8 3. Place Film Into Cartridge 9 4.
DESCRIPTION PAGE 5. Insert Memory Card 10 6. Insert Cartridge 10 7. Power On/Off Converter 10 8. Flip Image 10 9. Convert Image 11 10. Edit Image Options – Flip, Mirror, Rotate 11 11. Transfer Digital Images to Computer 12 12. Convert Slides or B&W Images 13 13. Message – Memory Full 13 14.
Before Using the F2D Converter This section provides important safety information that you should read before using your F2D Converter. FCC Certifications This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Warning: Warranty will be void if mishandled. Please take care in handling the Wolverine Device: ?? Do not drop or handle too aggressively as it may cause damage to the device. ?? Do not allow the device to come into contact with water or other liquids. In the event that water or other liquids enters the interior, immediately turn off the device.
?? Do not open the outer case. This unit does not require or have batteries. ?? Do not move or disconnect the device from the computer while the device is reading/writing data. This may cause damage to the data and/or the device. ?? Under no circumstances should the user try to repair the device. Doing so may cause electrical shock and void the warranty. WOLVERINE DATA IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES, INCLUDING LOSS OF DATA. ALWAYS BACK UP ALL DATA.
Wolverine Data is not responsible for any data stored on the returned Product, please backup any data prior to shipping the unit. All OUT OF WARRANTY repairs maybe subject to a normal repair fee. Please contact your dealer or Wolverine Data for current charges. Having difficulty using this product? Wolverine Data is here to help. Please try the following options before returning the product to the store: ?? Many problems can be resolved by reading this manual ?? Visit www.wolverinedata.
simple to use device to convert all your 35mm film negatives and slides into a 5 mega pixel digital images in seconds. So simple to use, it only requires a push of button - NO computer or software is needed. Use it right out of the box to convert all your 35mm films by simply plugging it into an AC outlet or any USB port. All images are saved directly on your SD memory card for your convenience to instantly play them on the unit, or through your Digital Picture Frame, or upload them to your computer.
Fast Track Guide This Fast Track Guide takes you through the steps involved in setting up your Converter and using it. 1. CLEAN CONVERTER SCANNER 2. ATTACH POWER For best results we highly recommend cleaning the inside of the Converter using the included cleaning brush before every new use. Insert the brush face down in the Converter base opening and gently dry-clean the inside as shown in picture. Either the included AC power adapter or computer USB port can power the Converter.
3. PLACE FILM INTO FILM CARTRIDGE 4.
5. INSERT MEMORY CARD 6. INSERT CARTRIDGE SD Card Insert cartridge into Right Side of the F2D Converter with Insert your SD memory card Upside Down in the card reader of the back of the unit. The Gold Contacts will be facing up.
7. POWER ON/OFF 8.
9. CONVERT IMAGES 10. EDIT IMAGE OPTIONS 1 2 3 4 On screen red blinking dot is an indication that the Converter is ready to convert. Press the button once and wait for five seconds. 5 Highlighted icon in yellow is current selected option. Use the < / FLIP > or < / MIRROR > buttons to choose other options. Press < OK > to select option. 1. 2. Save Rotate image clockwise 3. 4. 5.
11. TRANSFER DIGITAL IMAGES TO COMPUTER Images can be uploaded to a computer through a computer’s built-in SD card reader or any external SD memory card reader. Images can be transferred to a computer using the Converter acting as a memory card reader by following these steps: 1. Insert memory card into Converter Gold Contacts Facing Up 2. Plug Converter into a computer USB port 3. Turn on Converter 4. Press < /FLIP> button until USB icon is in yellow 5. Press < OK > button to select USB mode.
12. CONVERT SLIDES or B&W IMAGES 13. MESSAGE - MEMORY FULL Source The unit is always defaulted to convert negative film. To convert slides or B&W images turn on the unit. Press / FLIP> button two times until the “Source” option is highlighted in yellow. Press < OK > button to select. Negative Slides B&W Use the < / FLIP> button to choose from: 1. Negatives 2. Slides 3. B&W Insert Slides or B&W cartridge into the Converter. Follow steps 7 & 8 in this manual to convert image.
14. PLAYBACK Play The Converter can be used to view images saved on the SD memory card. To play a slide show of the images from the “Home” screen Select the “Play” mode. Converter defaults to auto slide show play mode To pause at an image press < OK > button. To resume slide show play mode press < OK > button. Use the directional arrow buttons < Flip > or < Mirror > to highlight “EXIT” icon in yellow. Press < OK > to resume Playback.
Technical Support For technical support, warranty service, or paid service please contact Wolverine Data at Support@wolverinedata.com or by calling 949-458-9888 M-F 9:00-5:00 Pacific Time Specifications Image Sensor: Lens: LCD Memory Slot Focus Range: Exposure Control: Color Balance: Scan Quality Data Conversion Scan Method Light Source Interface: USB Configuration Power: Dimensions Weight 1/1.8” inch 5 mega pixel CMOS sensor F no.= 2.0, 4 Glass elements, 1.
One-Year Limited Warranty (United States Only) Wolverine Data manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry-standard practices. Wolverine Data warrants that the hardware products it manufactures will be free from defects in materials and workmanship. The limited warranty term is one year beginning on the date of invoice, as further described in the following text.
During the one-year period beginning on the invoice date, Wolverine Data will repair or replace products returned to Wolverine Data's facility. To request limited warranty service, you must contact Wolverine Data's Customer Technical Support within the limited warranty period. Refer to the section titled TECHNICAL SUPPORT to find the appropriate telephone number for obtaining customer assistance. If limited warranty service is required, Wolverine Data will issue a Return Material Authorization Number.
LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS LIMITED WARRANTY STATEMENT. ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER SUCH PERIOD.
