Owner manual

ManualsBrandsWolo ManualsLighting7950-A Lookout Plus

LOOKOUT

PLUS LED LIGHT BAR

INSTALLATION MANUAL

Model 7950-A

Your purchase of a Wolo warning light is the perfect choice to complement your vehicle. Wolo’s warning lights are

manufactured with the ﬁnest materials. Before being packaged, each light is tested to meet our high standards

and ensure a perfect working light. Our quality workmanship and components are Wolo’s assurance that this

product will provide years of dependable service. If you need help using your new Wolo warning lights, our

technicians are available to answer your questions, Monday thru Friday, from 9 AM to 4 PM EST at 888-550-4676.

Before installation of the light bar is attempted, it is important to read these instructions completely. The lives of

people are dependent on a proper installation of the light bar to the vehicle. The person installing this light bar

must have advanced knowledge of the proper method for mounting and securing the light bar to a vehicle’s roof

or exterior, as well as knowledge of the vehicle’s electrical system. Again, read this manual completely and note

any messages marked “IMPORTANT” or “WARNING’’. A safe installation will prevent serious injury or damage

to the vehicle.

LOOKOUT comes completely wired and does not require any internal wiring by the installer. The power cable

has all the required wires with factory installed terminals and connectors for a successful installation.

Installation of the LOOKOUT Light Bar requires drilling into the vehicle. The installer must carefully inspect both

sides of the selected locations to ensure that there are no components, wires and/or any other vehicle part that

could be damaged by drilling. IMPORTANT: Always de-burr any drilled holes, ensuring that there are no sharp

edges. Install a rubber grommet into all metal holes that the wires are being routed through.

Always refer to the vehicle’s shop manual for deployment location of air bags. Never install the light bar’s switch

control panel, wires and or components in the deployment area of any air bag. Improper installation could

reduce the effectiveness of the vehicle’s air bag system and or project an object that could cause serious

personal injury or death to driver and passenger. The user/installer assumes all responsibility to properly

access a safe mounting location of the light bar’s control panel, to provide ultimate safety to the driver and

passengers inside the vehicle.

The vehicle operator and or maintenance department should inspect the light bar frequently to ensure all

brackets are securely attached to the vehicle and that all mounting hardware is free of corrosion.

The light bar’s control panel should be mounted in a location where the switches can be easily reached. Never

attempt to turn light bar on/off when driving under hazardous conditions.

These installation instructions should always be kept and stored in a safe location so that they can be referred

to when information, maintenance or reinstallation is required.

Failure to follow all safety precautions and installation procedures outlined in these instructions could result in

property damage to the vehicle, serious injury or death to you or others.

MOUNTING LIGHT BAR

1. Place the light bar on the selected location of the vehicle’s roof. A preferred mounting position on the roof

is close to the B-pillar, which is the strongest part of the roof. IMPORTANT: Make sure the light bar is facing

the correct direction. NOTE: there is a label on the light’s front lens indicating the forward facing work light.

Summary of content (5 pages)

PAGE 1
LOOKOUT® PLUS LED LIGHT BAR INSTALLATION MANUAL Model 7950-A Your purchase of a Wolo warning light is the perfect choice to complement your vehicle. Wolo’s warning lights are manufactured with the finest materials. Before being packaged, each light is tested to meet our high standards and ensure a perfect working light. Our quality workmanship and components are Wolo’s assurance that this product will provide years of dependable service.
PAGE 2
. Make sure the selected location of the light bar will allow the stainless steel straps to attach to the vehicle window ledge on both the driver’s and passenger sides. See fig 1. 3. A 1/2’’ hole is needed to be drilled in the roof to route both cables into the interior of the vehicle. Mark the desired hole location; remove the light bar from the roof and drill the hole.
PAGE 3
11. Tighten the two-(2) tension adjustment bolts evenly. While tightening the bolts make sure the light bar remains in the desired mounting position on the roof. Torque bolts to 10-12 ft-lbs. Failure to properly tighten the tension adjustment bolts and straps could result in damage to the vehicle and/or injury to driver or others. 12.
PAGE 4
19. Route the cable that has six-(6) colored wires to the switch controller. Match the cable’s colored wires to the same colored wires coming from the switch controller. Connect the wires together using the insulated bullet terminals’ that are factory installed onto the wires ends. Make sure the terminals rubber insulator fully covers the metal terminal. See fig. 8. WIRING POWER CABLE See fig 8 Cable that has two wires (red and black) 20.
PAGE 5
Traffic Advisory: There are three-(3) selectable traffic advisory light patterns to choose from. The pattern in use will display on the switch controller’s flash pattern indicator. • To turn on traffic advisory: press the switch button TRAFFIC FLASH. • Select the traffic advisory light pattern by using the THREE ARROWS. • To turn off traffic advisory: press the switch button TRAFFIC FLASH until you hear a beep. Rear Work Lights: There are two powerful clear lights, one in each corner of the light bar.